Bristol and Bath Science Park

There are two key areas of development across wind turbine blade lifecycles with the potential to reduce the impact of wind energy generation: (1) deploying lower-impact materials in blade structures and (2) developing low-impact blade recycling solution(s). This work evaluates the feasibility of using natural fibres to replace traditional glass and carbon fibres within state-of-the-art offshore blades. The structural design of blades was performed using Aeroelastic Turbine Optimisation Methods and lifecycle assessment was conducted to evaluate the environmental impact of designs. This enabled the matching of blade designs with preferred waste treatment strategies for the lowest impact across the blade lifecycle. Flax and hemp fibres were the most promising solutions; however, they should be restricted to use in stiffness-driven, bi-axial plies. It was found that flax, hemp, and basalt deployment could reduce Cradle-to-Gate Global Warming Potential (GWP) by around 6%, 7%, and 8%, respectively. Cement kiln co-processing and mechanical recycling strategies were found to significantly reduce Cradle-to-Grave GWP and should be the prioritised strategies for scrap blades. Irrespective of design, carbon fibre production was found to be the largest contributor to the blade GWP. Lower-impact alternatives to current carbon fibre production could therefore provide a significant reduction in wind energy impact and should be a priority for wind decarbonisation.

Fibre reinforced polymer (FRP) materials are well established in both the wind energy and aerospace industries, with the adoption of FRPs beginning to grow significantly in the automotive sector due to their favourable mechanical and physical properties. Their increased usage, coupled with the inherent complexity of forming FRP–FRP joints, has led to an increase in adhesives as a typical joining method. However, such adhesive joints pose a challenge when undertaking repair or at end-of-life (EoL). Separating the joint to facilitate recycling of the high-value FRP can be extremely labour- and time-intensive.Therefore, the introduction of debondable and reversible technologies into conventional structural adhesives such as acrylics, epoxies and polyurethanes has begun to attract interest within academia and industry which can overcome this challenge by demonstrating reversibility. Nevertheless, such adhesives are at various stages of technology readiness. The next step in adhesive materials development aims to meet current requirements and deliver an evolutionary advantage by enabling repair (when necessary), recycling, and transition towards a circular economy for FRP materials. For example, the use of reversible chemistries such as Diels-Alder or Covalent Adaptable Networks.This comprehensive review considers the latest literature for current debonding technologies including mechanical and thermal debonding, thermally expanding microspheres, induction heating, foaming agents and chemical degradation as well as a variety of reversible chemistries that could be introduced into adhesives for potential use in FRP-FRP joints, including how such reversibility might be activated and any consequences for practical application. The aim is to give readers a deeper understanding of their properties and potential application.

BackgroundA novel bi-exponential method has emerged to estimate critical speed (CS) and D-prime (D′) from a 3-min all-out test (3MT).ObjectivesTo compare CS analysis methods to determine whether parameter estimations were interchangeable. Reference values and relationships with key soccer match-play variables were explored.MethodsThirteen elite male youth (14–15 years old) players completed a 30 m shuttle run 3MT to estimate CS, D′, rate of speed decline time constant, maximal speed (Smax), time to Smax (tmax), and fatigue index (FI), using the traditional method and bi-exponential model on average (Bi-ExpAverage) and max speed settings (Bi-ExpMax-Speed). High-speed running (HSR) and sprinting distances and counts, and the number of accelerations were collected from two matches. Magnitude-based inferences (p < 0.05) with smallest worthwhile change of 0.2 effect sizes were used to analyse differences. Pearson’s and Spearman’s correlation coefficients were used to measure associations between CS model variables and match-play parameters.ResultsThere were significant differences between the traditional method and both bi-exponential models for CS and D′, as well as between the bi-exponential models for all variables except tmax. Using the Bi-ExpAverage model, strong correlations (r = 0.70–0.73; p < 0.05) were observed for D′ and FI with the number of standardised and individualised HSRs, respectively. With the Bi-ExpMax-Speed model, there were strong correlations (r/ρ = 0.64–0.68; p < 0.05) between D′ and the number of standardised HSRs and sprints, and the number of individualised sprints.ConclusionThere is a lack of interchangeability between analysis methods. It appears that D′ and FI from the bi-exponential models could be associated with high-intensity actions in soccer match-play.

Automated Fibre Placement requires accurate control of the heater power to deposit the material at appropriate temperatures throughout the process. This paper presents a simple semi-empirical thermal model of the process which correlates the heater power and the layup speed with the substrate surface temperature. The deposition temperature was measured over a range of heater powers and layup speeds. The experimental data is used to define and validate a semi-empirical thermal model for two classes of materials used in conjunction with a diode laser: carbon fibre reinforced thermoplastics and bindered dry fibres. This enables open-loop, speed dependent heater power control, based on defining and programming the speed dependent heater power function in the machine controls.

ABSTRACTThe aim of this study was to compare the physical and movement demands between training and match-play in schoolboy and academy adolescent rugby union (RU) players. Sixty-one adolescent male RU players (mean ± SD; age 17.0 ± 0.7 years) were recruited from four teams representing school and regional academy standards. Players were categorised into four groups based on playing standard and position: schoolboy forwards (n = 15), schoolboy backs (n = 15), academy forwards (n = 16) and academy backs (n = 15). Global positioning system and accelerometry measures were obtained from training and match-play to assess within-group differences between conditions. Maximum data were analysed from 79 match files across 8 matches (1.3 ± 0.5 matches per participant) and 152 training files across 15 training sessions (2.5 ± 0.5 training sessions per participant). Schoolboy forwards were underprepared for low-intensity activities experienced during match-play, with schoolboy backs underprepared for all movement demands. Academy forwards were exposed to similar physical demands in training to matches, with academy backs similar to or exceeding values for all measured variables. Schoolboy players were underprepared for many key, position-specific aspects of match-play, which could place them at greater risk of injury and hinder performance, unlike academy players who were better prepared.

Extant rhinos are the largest extant herbivores exhibiting dietary specialisations for both browse and grass. However, the adaptive value of the wear-induced tooth morphology in rhinos has not been widely studied, and data on individual cusp and tooth positions have rarely been published. We evaluated upper cheek dentition of browsing Diceros bicornis and Rhinoceros sondaicus, mixed-feeding R. unicornis and grazing Ceratotherium simum using an extended mesowear method adapted for rhinos. We included single cusp scoring (EM(R)-S) to investigate inter-cusp and inter-tooth wear patterns. In accordance with previous reports, general mesowear patterns in D. bicornis and R. sondaicus were attrition-dominated and C. simum abrasion-dominated, reflecting their respective diets. Mesowear patterns for R. unicornis were more attrition-dominated than anticipated by the grass-dominated diet, which may indicate a low intake of environmental abrasives. EM(R)-S increased differentiation power compared to classical mesowear, with significant inter-cusp and inter-tooth differences detected. In D. bicornis, the anterior cusp was consistently more abrasion-dominated than the posterior. Wear differences in cusp position may relate to morphological adaptations to dietary regimes. Heterogeneous occlusal surfaces may facilitate the comminution of heterogeneous browse, whereas uniform, broad grinding surfaces may enhance the comminution of physically more homogeneous grass. A negative tooth wear gradient was found in D. bicornis, R. sondaicus and R. unicornis, with wear patterns becoming less abrasion-dominated from premolars to molars. No such gradients were evident in C. simum which displayed a uniform wear pattern. In browsers, premolars may be exposed to higher relative grit loads, which may result in the development of wear gradients. The second premolar may also have a role in food cropping. In grazers, high absolute amounts of ingested abrasives may override other signals, leading to a uniform wear pattern and dental function along the tooth row, which could relate to the observed evolution towards homodonty.

Shelters such as leaf nests, tree holes or vegetation tangles play a crucial role in the life of many nocturnal mammals. While information about characteristics and availability of these resources may help in conservation planning, nest use gives an indication about a species’ social organisation. The northern giant mouse lemur (Mirza zaza) is threatened by habitat loss within its restricted range. Our aim was to examine nest site preferences of M. zaza and to explore the species’ social organisation by examining sleeping site aggregation size and genetic relatedness within and between such aggregations. In the Ankarafa Forest inside Sahamalaza – Iles Radama National Park, northwestern Madagascar, we radio-tagged five male and three female M. zaza and followed them for 2.5 months during the dry season. We identified sleeping trees and observed animals during emergence in the evening and return in the morning. We compared sleeping trees and microhabitats around nest sites to trees and habitat used during nightly activity and to random sites. We found that nests were well covered by canopy, even during the dry season, and were located near the tree trunk a few meters below the tree top. Nest sites were characterised by large (&gt; 30 cm DBH) and tall trees (&gt;16 m) with many lianas. Up to four animals shared one to three group-exclusive nests for up to 50 days. Two of the nest groups included two and three males with fully developed testes. Relatedness data revealed that the adult males sharing nests were either unrelated or closely related. These data suggest that M. zaza is sleeping in social nest groups including multiple males, which is unusual among nocturnal strepsirrhines. Apart from protecting suitable sleeping trees and discouraging selective logging of large trees, we recommend conducting further studies on the species’ social organisation throughout an entire season.