- Book Chapter
- 10.1007/978-981-96-1945-0_23
When Sediments Meet Shells: A Promising Geotechnical Story
- Jan 01, 2025
- Claudia Vitone + 4 more +4
Publications from 2021 to 2026
Showing 10 of 10 papers
When Sediments Meet Shells: A Promising Geotechnical Story
Accelerated Direct Carbonation of Steel Slag and Cement Kiln Dust: An Industrial Symbiosis Strategy Applied in the Bergamo-Brescia Area.
The carbonation of alkaline industrial wastes is a pressing issue that is aimed at reducing CO2 emissions while promoting a circular economy. In this study, we explored the direct aqueous carbonation of steel slag and cement kiln dust in a newly developed pressurized reactor that operated at 15 bar. The goal was to identify the optimal reaction conditions and the most promising by-products that can be reused in their carbonated form, particularly in the construction industry. We proposed a novel, synergistic strategy for managing industrial waste and reducing the use of virgin raw materials among industries located in Lombardy, Italy, specifically Bergamo-Brescia. Our initial findings are highly promising, with argon oxygen decarburization (AOD) slag and black slag (sample 3) producing the best results (70 g CO2/kg slag and 76 g CO2/kg slag, respectively) compared with the other samples. Cement kiln dust (CKD) yielded 48 g CO2/kg CKD. We showed that the high concentration of CaO in the waste facilitated carbonation, while the presence of Fe compounds in large amounts caused the material to be less soluble in water, affecting the homogeneity of the slurry.
Read moreBriefing: Low-alkali cements as inhibitors of alkali–silica reaction
In this study, a compositional parameter, such as the maximum allowable total alkali content of cement (Matac) is proposed to identify the non-CEM I cements for their use as inhibitors of alkali–silica reaction in concrete. The Matac values for different types of Italian non-CEM I cements (cement type CEM III and CEM IV) were calculated using the authors' previously published experimental results. The Matac value is found to change significantly with the type of cement considered (blast furnace cement, pozzolanic cement made from coal fly ash or natural pozzolana). For cements of the same type (pozzolanic cements made with different natural pozzolanas), very similar Matac values are obtained. It is also demonstrated that the Matac value calculated for a CEM I cement is congruent with the limit of 0·6% as Na2Oeq commonly specified for the total alkali content of low-alkali Portland cements.
Read moreThe Calcium Looping Process for Low CO2 Emission Cement and Power
Modeling the Adsorption Behavior of Linear End-Functionalized Poly(ethylene glycol) on an Ionic Substrate by a Coarse-Grained Monte Carlo Approach
The rheology of cement pastes can be controlled by polymeric dispersants such as branched polyelectrolytes that adsorb on the surfaces of silicate particles. In the present work, we analyze the adsorption behavior of ad hoc-prepared end-carboxylated poly(ethylene glycol), or PEG, on CaCO(3) particles as a model of cement in an early hydration stage. The experimental adsorption isotherms form the base of a theoretical study aimed at unraveling polymer conformational aspects of adsorption. The study was carried out with Monte Carlo simulations using a coarse-grained bead-and-spring model of linear end-charged polymer chains adsorbing on a flat, continuous, uniformly charged surface. The adsorption driving force was introduced by a Debye-Hückel electrostatic screened potential to describe the interaction between the negatively charged end group of PEG and the positively charged CaCO(3) surface empirically. With a suitable length-scale conversion between real PEG and the coarse-grained model, the calculated and experimental adsorption isotherms can be semiquantitatively compared. The theoretical results reproduce the fundamental aspects of polymer adsorption, in essential agreement with analytical approaches relating the isotherm shape to the polymer conformational properties. The conformational transition mushroom-brush of the adsorbed polymer is located on the isotherm and is related to the molecular shape. The solvent quality effect and the solution ionic strength are also considered, and their implications on the isotherms are discussed.
Read morePhotocatalytic Properties of Cement-Based Plasters and Paints Containing Mineral Pigments
Innovative cement-based premix products for surface coating of buildings that possess photocatalytic activity arouse great interest because of the results they can achieve in reducting air pollution and maintaining aesthetics. This photoactivity is induced by a photocatalyst, titanium dioxide, that can accelerate the oxidation processes of air pollutants, particularly nitrogen oxides and volatile organic compounds, which are mainly produced by incomplete combustion of fuel and are present in urban environments through the exhaust gases of motor vehicles. Surfaces that are coated with these products acquire a self-cleaning characteristic (maintenance of original color) because the decomposition of organic compounds significantly reduces the ability of atmospheric particles to adhere to treated surfaces, thus facilitating their removal and ensuring a more durable color. These products are particularly suited for use in highly congested areas (i.e., historical centers of cities, tunnels, roads), where air pollution reaches significant levels. This study describes the photocatalytic performances of a series of premix products containing mineral pigments. The tested products are based on hydraulic binders (natural hydraulic lime and cement), and the pigments are inorganic. A wide range of colors was chosen, and the performances of base products were investigated to provide a wider choice to the designers. After a brief introduction of the principles of photocatalysis, the results of a wide experimental work are described. Some consideration of methods of curing and natural exposure is also reported.
Read moreLocalization of sound sources by means of unidirectional microphones
This paper describes the results of a new approach devoted to the localization of ground borne acoustic sources. It is demonstrated that an array made of at least three unidirectional microphones can be exploited to identify the position of the source. Sound features extracted either in the time domain or in the frequency domain are used to localize the direction of the incoming sound. This information is then fed into a semi-analytical algorithm aimed at identifying the source location. The novelty of the method presented here consists in the use of unidirectional microphones rather than omnidirectional microphones and in the ability to extract the sound direction by considering features like sound amplitude rather than the time of arrival. Experimental tests have been undertaken in a closed environment and have demonstrated the feasibility of the proposed approach. It is believed that this method may pave the road toward a new generation of reduced-size sound detectors and localizers, and future work is described in the conclusions.
Read moreCross-Linking of Poly(vinyl alcohol) Chains by Al Ions in Macro-Defect-Free Cements: A Theoretical Study
The significant increases in flexural strength achieved in macro-defect-free cements have been attributed to a reduction in the density of defects in the materials as well as to chemical reactions occurring between the organic constituent, i.e., the poly(vinyl alcohol) (PVA) polymer, and inorganic ions coming from the hydration products of the cement. In particular, it has been suggested that PVA chains are partially linked together by Al ions. This phenomenon has been investigated here by studying the structure and the energetics of Al-PVA models with ab initio theoretical methods. The achieved results strongly support the existence of a cross-linking of PVA chains by Al ions, even in the presence of structural deformations of the PVA chains. The vibrational frequency of a stretching mode related to the O atoms bonded with Al has been also evaluated, which may represent a fingerprint for an experimental identification of cross-linking.
Read moreAnodic System for Cathodic Protection of New Reinforced Concrete Structures: Laboratory Experience
Abstract Cathodic Protection is presently a well proven and cost effective technique to stop chloride induced rebar corrosion on existing concrete structures. In the event that a new structure is likely to be exposed to an environment in which chloride induced corrosion is possible, then, as a means of preventive maintenance, cathodic protection can be applied during the construction phase, before concrete casting. This paper describes a new technique wherein an anodic grid, consisting of expanded titanium mesh strips, is installed on the rebar mat to be cathodically protected before concrete casting. Laboratory results are presented with particular emphasis on the current distribution and rebar polarization levels achieved.
Read moreSnap-back softening instability in high-strength concrete beams
Three-point bending tests on pre-cracked slabs of high-strength concrete are interpreted on the basis of a virtual crack propagation model. As theoretically shown by the model, a snap-back softening instability appears only for initial crack lengths smaller than 0.3 times the beam depth. As a limit-case, when the material is sufficiently brittle or the specimen size is sufficiently large, such an instability can be predicted by the LEFM condition K1=KIC.
Read more