Metalsa (Germany)

Abstract The automotive industry has searched for alternatives to reduce the weight of vehicles without neglecting the user’s safety by using new materials. Advanced high-strength steels of complex phases are used in structural applications requiring good performance and reducing the weight of vehicles. However, these steels have shown edge cracking, known as fissure, during processing, which has become a challenge for steelmakers and other companies that rely on them to manufacture structural components. Such defects can be associated with the interaction between the different microstructural constituents of the steel, such as various phases and precipitates generated during its processing to achieve the required mechanical properties. The present work presents the studies evaluate the effect that processing and chemical composition exerts on edge cracking in complex phase steels of grade 800 MPa produced by different steelmaking routes.

A persistent increase in the permeability of rock mass caused by transient stress disturbances, if present, could explain the variation in the groundwater level in far fields, increase in petroleum production caused by earthquakes or artificial vibrations in enhanced oil recovery, and induction of earthquakes by seismic waves in intermediate and far fields. However, it has not been verified whether the transient stress disturbances induce an increase or decrease in the rock permeability. In this study, the permeability values of intact and triaxially fractured Kushiro Cretaceous sandstone and Shikotsu welded tuff were measured before and after transient axial stress or pore pressure disturbances to clarify the effects of transient stress disturbances on rock permeability. According to the experimental results, the stress disturbances showed either decreasing or increasing effects on the permeability depending on the rock type and experimental conditions. However, when focusing on the fractured rocks rather than the intact ones, which would be more important in field applications, the argillaceous Kushiro Cretaceous sandstone mainly exhibited decreasing effects and the glassy Shikotsu welded tuff mainly exhibited increasing effects.

<div class="section abstract"><div class="htmlview paragraph">Frame rail design advances for the heavy truck industry provide numerous opportunities for enhanced protection of fuel storage systems. One aspect of the advanced frame technology now available is the ability to vary the frame rail separation along the length of the truck, as well as the depth of the frame. In this study, the effect of incorporating the fuel storage system within advanced technology tapered frame rails was evaluated using virtual testing under impact conditions. The impact performance was evaluated under a range of horizontal impacts conditions. The performance observed was quantified and then compared with previous testing of baseline diesel tank systems. Fuel storage system impact performance metrics over the range of crash conditions considered were quantified using virtual testing methods. The results obtained from the application of the impact performance evaluation methodology were then described. The results indicated that substantial improvements in fuel storage system impact protection were available utilizing the advanced tapered frame rail technology. Opportunities available with the use of advanced frame technologies were described.</div></div>

The boron and nitrogen contents of GaAs and InP melts equilibrated with B 2 O 3 flux were examined at 1523 and 1373 K, respectively, using a chemical equilibrium technique. GaAs or InP was melted with B 2 O 3 flux in a silica ampoule with and without a BN crucible. The boron content decreased with increasing nitrogen content in both of the melts equilibrated with B 2 O 3 flux and BN. The solubility product of BN in the melts was expressed as a function of nitrogen content. The relationship between the boron and nitrogen contents of a GaAs melt coexisted with BN agreed well with that in the residue after LEC crystal growth of GaAs. The boron content of the GaAs melt coexisted with silica was much larger than that of the GaAs melt with BN. It was suggested that the reduction of B 2 O 3 by silicon introduced into the melt from silica led the increase of boron content.

Continuing benchtop studies using Hanford single-shell tank (SST) simulants and actual Oak Ridge National Laboratory (ORNL) low-level waste (LLW), employing a new denitration process for converting nitrate to ammonia and ceramic (NAC), have conclusively shown that between 85 and 99% of the nitrate can be readily converted to gaseous ammonia. In this process, aluminum powders can be used to convert alkaline, nitrate-based supernate to ammonia and an aluminum oxide-sodium aluminate-based solid. The process may be able to use contaminated aluminum scrap metal from DOE sites to effect the conversion. The final, nitrate-free ceramic product can be pressed and sintered like other ceramics or silica and/or fluxing agents can be added to form a glassy ceramic or a flowable glass product. Based upon the starting volumes of 6.2 and 3.1 M sodium nitrate solution, volume reductions of 50 to 70% were obtained for the waste form produced. Sintered pellets produced from supernate from Melton Valley Storage Tanks (MVSTs) have been leached in accordance with the 16.1 leach test for the radioelements {sup 85}Sr and {sup 137}Cs. Despite lengthy counting times, {sup 85}Sr could not be detected in the leachates. {sup 137}Cs was only slightly above background and corresponded to a leach index of 12.2 to 13.7 after 8 months of leaching. Leach testing of unsintered and sintered reactor product spiked with hazardous metals proved that both sintered and unsintered product passed the Toxicity Characteristic Leaching Procedure (TCLP) test. Design of the equipment and flowsheet for a pilot demonstration-scale system to prove the nitrate destruction portion of the NAC process and product formation is under way.

The production of titanium nitride, TiN, whiskers by reaction of sodium titanium bronze, NaxTiO2 (STB), with excess sodium cyanide, NaCN, at 1000°C is reported. The solubility of Ti from a STB in molten NaCN has been estimated experimentally. The TiN whiskers obtained under different experimental conditions have been examined by scanning electron microscopy and analyzed by analytical electron microscopy.

CURimi SESQUIOXIDE