Molecular Design International (United States)

A molecular capsule (1) consisting of two calix[4]pyrroles connected via ethylene diamide linkers has been prepared as an anion receptor. 1H NMR spectroscopic studies carried out in CD2Cl2 revealed that receptor 1 recognizes a variety of anions with different binding modes and stoichiometries. For instance, receptor 1 binds fluoride and acetate with 1:2 receptor/anion stoichiometry and other test anions with 1:1 stoichiometry in solution when their respective tetrabutylammonium (TBA+) salts were used. In contrast, with tetraethylammnium (TEA+) salts, receptor 1 forms 1:2 complexes with chloride and bromide in addition to fluoride, overcoming expected Columbic repulsions between the anions co-bound in close proximity. Receptor 1 is also able to bind oxoanions, such as oxalate (C2O42-), dihydrogen phosphate (H2PO4-), sulfate (SO42-), and hydrogen pyrophosphate (HP2O73-), in the form of 1:1 complexes as the result of presumed cooperation between the two calix[4]pyrrole subunits. The selectivity of receptor 1 for fluoride versus dihydrogen phosphate varies depending on their relative concentrations. For instance, in the presence of less than 1.0 equiv of an equimolar mixture of fluoride and dihydrogen phosphate, receptor 1 shows high selectivity for dihydrogen phosphate. In contrast, in the presence of ≥2.0 anion equiv, receptor 1 binds fluoride preferentially, forming a 1:2 complex. Moreover, when treated with F-, the preformed 1:1 H2PO4- complex of receptor 1 is converted to the corresponding 1:2 receptor/fluoride complex with the release of the prebound dihydrogen phosphate anion. As inferred from gas-phase computations, this seemingly counterintuitive behavior is rationalized in terms of the precomplexed dihydrogen phosphate serving to reduce the reorganization energy required to bind two fluoride anions. The presence of a water molecule in addition to the bound fluoride anions may also favor the formation of the 1:2 F- complex. The present study provides a new approach for fine-tuning the binding selectivity of polytopic anion receptors.

The conformations of a series of organophosphine oxides, OP(CH3)2R, where R = methyl, ethyl, isopropyl, tert-butyl, vinyl, and phenyl, are predicted using the MP2/cc-pVTZ level of theory. Comparison of potential energy surfaces for rotation about P-C bonds with crystal structure data reveals a strong correlation between predicted location and energetics of minima and histograms of dihedral angle distributions observed in the solid state. In addition, the most stable conformers are those that minimize the extent of steric repulsion between adjacent rotor substituents, and the torsional barriers tend to increase with the steric bulk of the rotating alkyl group. MM3 force field parameters were adjusted to fit the MP2 results, providing a fast and accurate model for predicting organophosphine oxides shapes-an essential part of understanding the chemistry of these compounds. The predictive power of the modified MM3 model was tested against MP2/cc-pVTZ conformations for triethylphosphine oxide, OP(CH2CH3)3, and triphenylphosphine oxide, OP(Ph)3.

We had designed and prototyped original gamma-type circulating flow stirling engine (CFSE) with pulse converter branch and confluent connection in operating gas flow for application of waist heat recovering, low temperature differential Stirling engine. Though the pulse converters are incomplete preventing reverse flow compared with lead valve, they are simpler, low pressure loss and wide section area, it could change the heater and cooler flow into counter flow heat exchanger. A One-cylinder, 1.0kw experimental CFSE model is manufactured. In addition, DP and PP are connected by oval-gear drive for enhancement of indicated power. For cancel the side thrust of DP and PP, contra-rotating drive system is adopted.

We had designed and prototyped original gamma-type circulating flow stirling engine (CFSE) with pulse converter branch and confluent connection in operating gas flow for application of waist has recovering, low temperature differential Stirling engine. Though the pulse converters are incomplete preventing reverse flow compared with lead valve, they are simpler, low pressure loss and wide section area, it could change the heater and cooler flow into counter flow heat exchanger. A One-cylinder, 1.0kw experimental CFSE model is manufactured. In addition, DP and PP are connected by oval-gear drive for enhancement of indicated power. For cancel the side thrust of DP and PP, contra-rotating drive system is adopted.