- Book Chapter
1
- 10.1016/b978-1-85617-912-6.00001-3
Chapter 1 - Idealized Flow Machines
- Oct 07, 2011
- Theory of Aerospace Propulsion
- Pasquale M Sforza
Chapter 1 - Idealized Flow Machines
A study to modify and develop a turbofan engine using a micro turboprop engine has been conducted. The turbofan engine has been designed by adding a fan blade module as well as other required accessories to the existing turboprop engine. CFD and FEM methods were used for numerical analyses of the additional fan module to assess its aerodynamic performance and structural stability. Components of the fan module were fabricated with consideration for manufacture and assembly, and a test rig was also designed and built to measure the turbofan engine performance. The performances of the turbofan engine were measured and compared to an existing micro-turbojet engine. The performance tests were conducted in two phases: In the first phase, the robustness of the designed turbofan and test rig were investigated and in the second phase, the maximum power test has been conducted to measure performance variables such as engine thrust, engine exhaust temperature(EGT) and fuel flow rate according to the engine RPM. The test results indicated that the turbofan engine SFC was reduced by 40∼50% of the existing turbojet engine, demonstrating the successful implementation of turbofan characteristics.
Chapter 1 - Idealized Flow Machines
Chapter 1 - Idealized Flow Machines
Impact of a Jet A-1/HEFA blend on the performance and emission characteristics of a miniature turbojet engine
It is forecast that in the future, alternative fuels derived from non-petroleum sources will become the basic propellant for turbine aircraft engines. Currently, five types of aviation turbine fuel containing synthesized hydrocarbons are certified and accepted, and allow adding a maximum of 50% of synthetic component to conventional fuel. The experimental performance and the emission characteristics of a turbojet engine were investigated in this paper. The studies were conducted with the use of a miniature turbojet engine, which is the main component of a laboratory test rig. The test rig is an interesting solution for engine research, due to the fact that studies concerning full-scale aircraft engines are very complex and expensive. The literature of the subject contains many papers using small-scale turbojet engines for testing alternative fuels. However, most of them concern components of fuels, e.g. biodiesel, butanol, which do not have direct application in aviation. Two different fuel samples, a conventional Jet A-1 fuel and a blend of 48% synthesized paraffinic kerosene from hydroprocessed esters and fatty acids process with Jet A-1 were tested. This process is one of the routes of producing alternative fuel for aviation, approved by ASTM standard. The test rig studies were performed according to a specific profile of engine test, which models different modes of a turbojet engine’s operation. The obtained results are compared in relation to the results for neat Jet A-1 fuel and then discussed.
Read morePerformance analysis and dynamic modeling of a single-spool turbojet engine
The purposes of modeling and simulation of a turbojet engine are the steady state analysis and transient analysis. From the steady state analysis, which consists in the investigation of the operating, equilibrium regimes and it is based on appropriate modeling describing the operation of a turbojet engine at design and off-design regimes, results the performance analysis, concluded by the engine's operational maps (i.e. the altitude map, velocity map and speed map) and the engine's universal map. The mathematical model that allows the calculation of the design and off-design performances, in case of a single spool turbojet is detailed. An in house code was developed, its calibration was done for the J85 turbojet engine as the test case. The dynamic modeling of the turbojet engine is obtained from the energy balance equations for compressor, combustor and turbine, as the engine's main parts. The transient analysis, which is based on appropriate modeling of engine and its main parts, expresses the dynamic behavior of the turbojet engine, and further, provides details regarding the engine's control. The aim of the dynamic analysis is to determine a control program for the turbojet, based on the results provided by performance analysis. In case of the single-spool turbojet engine, with fixed nozzle geometry, the thrust is controlled by one parameter, which is the fuel flow rate. The design and management of the aircraft engine controls are based on the results of the transient analysis. The construction of the design model is complex, since it is based on both steady-state and transient analysis, further allowing the flight path cycle analysis and optimizations. This paper presents numerical simulations for a single-spool turbojet engine (J85 as test case), with appropriate modeling for steady-state and dynamic analysis.
Read morePrediction of emissions in turbojet engines exhausts: relationship between nitrogen oxides emission index (EI NOx) and the operational parameters
Prediction of emissions in turbojet engines exhausts: relationship between nitrogen oxides emission index (EI NOx) and the operational parameters
Read moreInvestigation of overall performance of turbofan engine with pulse detonation combustor in bypass duct
The performance model was established to study the performance of mixed exhaust turbofan engine with pulse detonation combustor (PDC) in the bypass duct. The effects of the total pressure loss of isolator and bypass circulation parameters on the characteristic of PDC and performance of engine were analyzed. Then, the sensitivity analysis of performance parameters was carried out on the influence of the components parameters. The performance of mixed exhaust turbofan engine with PDC in the bypass duct was compared with that of the conventional afterburner turbofan engine at the same design circulation parameters. The results show that to increase the total pressure loss of isolator is beneficial to the improvement of performance because of the improvement of pressure ratio; when fan pressure ratio is constant, with the increasing of bypass ratio, the specific fuel consumption and specific thrust increase; with the increasing of fan pressure ratio, when bypass ratio is 0.2 to 0.4, specific thrust increases first and then decreases. When bypass ratio is 0.4 to 0.5, specific thrust increases first and then remains constant. When bypass ratio is 0.5 to 0.9, specific thrust increases, but the rate of increase reduces. At different bypass ratio, specific fuel consumption decreases with increasing of fan pressure ratio; the performance of engine is more sensitive to the component parameters that directly affect the flow state parameters of the bypass duct; because of supercharging performance of PDC, PDC in the bypass duct only uses part of air flow to organize combustion that can make specific thrust of turbofan engine with PDC in the bypass duct and conventional afterburner turbofan engine are equivalent. Meanwhile, specific fuel consumption can be reduced by 27.7% at design point and 12.8%-26.8% at off-design points.
Read moreStudy of the Effects of Heat Exchanger Location on Turbofan Engine Performance
The article presents a numerical investigation of the impact of heat exchanger (HE) location on the performance of the geared turbofan engine (GTF). It discusses the development trend for aero engines, with a primary focus on the modification of the turbofan engine cycle by the addition of the heat exchanger. This paper presents the current state of research on heat exchangers and their application in aero engines. The paper focuses on the thermodynamic model of the GTF engine, with particular emphasis on its modification to study the impact of heat exchangers on engine performance. The assumptions and limitations of the model are also discussed. The study examines the effects of various locations of the heat exchanger in the GTF engine, as well as its efficiency and pressure drop, on the engine overall performance, as measured by thrust and specific fuel consumption (SFC). The study demonstrates that the use of HE has a positive effect on engine thrust, but it also leads to an increase in SFC. According to the results, the HE should be positioned in the core engine of the GTF to achieve maximum thrust. This is achieved when the HE core flow inlet is located at approximately half the pressure ratio of the high-pressure compressor (HPC). It was found that the cold side pressure losses of the HE have a significant impact on engine performance for high bypass ratio turbofan engines. The additional conclusion can be drawn that, when designing a heat exchanger, it is of the utmost importance to take care to minimize its impact on pressure losses in the external channel of the engine.
Read moreExperimental rigs for testing components of advanced industrial applications
This paper presents experimental rigs of the Research Centre for the Mechanics of Turbomachinery of the Department of Civil and Industrial Engineering of the University of Pisa. Most of them were designed and constructed to allow investigations of real machine components and to furnish more realistic results than basic tribological test rigs.Tilting pad journal bearings, as well as gears and complete gearboxes for advanced industrial applications, can be tested using the rigs described in the paper. A novel test rig with a power rating of approximately 1 MW allows investigations of the static and dynamic characteristics of high-performance tilting pad journal bearings for turbomachinery. A twin disc machine and closed loop gear test rig are used to investigate the different kinds of wear mechanisms occurring in gears. Functional and durability tests on planetary gearboxes for new turbo-fan engines could be performed using another novel large test rig. A circulating power configuration was adopted for most of the rigs so that only the power needed to cover the friction losses has to be supplied, while the circulating power can be more than 20 times higher. All the test rigs include very complex load applications and lubrication plants, as well as dedicated control and data acquisition systems.The rigs and related plants were designed and constructed through strong and fruitful collaborations between the university and some large and small–medium companies. Despite some limitations in the publication of the results as a result of the industrial sensitivity of the data, the synergy among these different actors was stimulating and fundamental for the realization of new advanced industrial applications.
Read moreDesign Considerations of Low Bypass Ratio Mixed Flow Turbofan Engines with Large Power Extraction
The possibility of extracting large amounts of electrical power from turbofan engines is becoming increasingly desirable from an aircraft perspective. The power consumption of a future fighter aircraft is expected to be much higher than today’s fighter aircraft. Previous work in this area has concentrated on the study of power extraction for high bypass ratio engines. This motivates a thorough investigation of the potential and limitations with regards to performance of a low bypass ratio mixed flow turbofan engine. A low bypass ratio mixed flow turbofan engine was modeled, and key parts of a fighter mission were simulated. The investigation shows how power extraction from the high-pressure turbine affects performance of a military engine in different parts of a mission within the flight envelope. An important conclusion from the analysis is that large amounts of power can be extracted from the turbofan engine at high power settings without causing too much penalty on thrust and specific fuel consumption, if specific operating conditions are fulfilled. If the engine is operating (i) at, or near its maximum overall pressure ratio but (ii) further away from its maximum turbine inlet temperature limit, the detrimental effect of power extraction on engine thrust and thrust specific fuel consumption will be limited. On the other hand, if the engine is already operating at its maximum turbine inlet temperature, power extraction from the high-pressure shaft will result in a considerable thrust reduction. The results presented will support the analysis and interpretation of fighter mission optimization and cycle design for future fighter engines aimed for large power extraction. The results are also important with regards to aircraft design, or more specifically, in deciding on the best energy source for power consumers of the aircraft.
Read morePython-Based Performance and Emissions Analysis of Turbojet and Turbofan Engines
This study provides systematic computational analysis of turbojet and turbofan propulsion system performance and emissions characteristics using simulation modeling developed in Python programming language. Simulations were carried out using pyCycle software developed by NASA with the capability to simulate thermodynamic cycles of propulsion systems. Design-point and parametric analysis were also conducted to investigate the impact of major parameters like the compressor pressure ratio and turbine inlet temperature on engine performance. The model of turbojet and turbofan were created with component-level accuracy including the compressor, combustor, turbine, fan, and nozzle modules. The models were solved to convergence with state-of-the-art nonlinear solver algorithms interfaced with OpenMDAO. Results indicate that the turbofan engine achieves significantly higher thrust and greater fuel efficiency than the turbojet, with a 69.5% improvement in thrust and a 54.9% reduction in thrust-specific fuel consumption (TSFC) at the design point. Computation of emissions was conducted from calculated fuel mass flow rates and considering CO₂ production. The results indicate that the turbofan engine produces 13% less CO₂ per hour and nearly 49% less CO₂ per unit of thrust than the turbojet, validating the environmental benefits of high-bypass turbofan configurations. The study confirms the applicability of Python-based simulation frameworks for accurate propulsion system performance and emissions prediction. Future work will focus on incorporating alternative fuel models and predictive NOₓ emission calculations to expand the environmental impact assessment capabilities.
Read moreGas Turbine Engine Testing Education at Western Michigan University
The development of a gas turbine engine test cell facility is described in this paper . The test c ell houses a mini turbo jet engine and a mini turboprop engine . The two turbine engines have the same type of gas generator. The engine s have been assembled by students using components purchased from the engine manufacturer . The test cell setup provides t he aeronautical engineering undergraduate students with a variety of engine data during engine runs in both numerical a nd graphical formats by using a developed LabVIEW -based interface . The data acquired from the sensors allow the students to determine th e component operating conditions and the air properties at the different stages along the air path . Through the lab experiments, the students are able to understand and validate the fundamental principles of gas turbine engines. More importantly, the lab p rovides the students with hands -on experience to apply the knowledge learned in classroom lectures to the real -time operation of turbine engines. The test cell facility promotes students interests in aeropropulsion. HE undergraduate stude nts majoring in aeronautical engineering at Western Michigan University (WMU) conduct turbine engine testing in the lab portion of the Aeropropulsion Systems course. The Aeropulsion Systems course runs for one semester and is taught at the senior level. One objective of the course, as is described in the ABET syllabus, is to teach students the fundamentals at work for the turbine engine components and the propulsion system as a whole. The Aeropropulsion System course, whic h is an introductory propulsio n class at the undergraduate level in the Mechanical and Aeronautical Engineering Department , has also a lecture portion . In the lecture part of the class, t he students learn the application of the various principles of thermodynamics and aerod ynamics to the operation of turbine engine s and their performance evaluations. T he turbine engine testing lab supplement s the theoretical knowledge acquired in the classroom by providing stude nts with hands -on experie nce required for working with a turbine engine. The engine t est sessions are normally conducted in groups of five to six students. Through various test runs , the students are able to understand and validate the reasoning behind assumptions and approximations invoked in classroom studies. The students run both scaled and full -size turbine engines. The full -size engine runs are conducted at the engine test cells in the Aviation Colleg e of WMU . Typically, the students will run turbofan and turbo shaft engines, such as the Boeing T-50, during those cell runs . In addition, the students also run two scaled engines. One is a turbojet and the second is a turboprop engine . Both of these engines are based on a MW 54 gas generator . As a result of the use of the different types of turbine engines, from turbojet to turboprop, and different sizes, from full to scaled, the course provides the student with a comp rehensive knowledge of both the fundamental theory and the real -life operation of the propulsion systems in aeronautical engineering. Despite it s small size, t he MW 54 turbine engine s used in the test cell perform all the basic fu nctions of full -scale turbine engine s. The engines have been selected mainly because of their simple setup and low maintenance, while providing the flexibility of operations necessary fo r propulsion education at the undergraduate level . T he turbojet version of the MW 54 engine was introduc ed in 2002. With only minor maintenance, the tu rbojet engine has provided stable and reliable engine operation experience to the students. T he student responses received since then have been overwhelming in terms of both teaching and learning. To further enrich students’ exposure to different types of turbine engines, a free turbine driven turboprop has been built recently in our test cell with purchased components and manufacturer -assembled sub -systems, such as the gear box. This addition further enhance s the
Read moreElectron microscopic study of soot particulate matter emissions from aircraft turbine engines.
The microscopic characteristics of soot particulate matter (PM) in gas turbine exhaust are critical for an accurate assessment of the potential impacts of the aviation industry on the environment and human health. The morphology and internal structure of soot particles emitted from a CFM 56-7B26/3 turbofan engine were analyzed in an electron microscopic study, down to the nanoscale, for ∼ 100%, ∼ 65%, and ∼ 7% static engine thrust as a proxy for takeoff, cruising, and taxiing, respectively. Sampling was performed directly on transmission electron microscopy (TEM) grids with a state-of-the-art sampling system designed for nonvolatile particulate matter. The electron microscopy results reveal that ∼ 100% thrust produces the highest amount of soot, the highest soot particle volume, and the largest and most crystalline primary soot particles with the lowest oxidative reactivity. The opposite is the case for soot produced during taxiing, where primary soot particles are smallest and most reactive and the soot amount and volume are lowest. The microscopic characteristics of cruising condition soot resemble the ones of the ∼ 100% thrust conditions, but they are more moderate. Real time online measurements of number and mass concentration show also a clear correlation with engine thrust level, comparable with the TEM study. The results of the present work, in particular the small size of primary soot particles present in the exhaust (modes of 24, 20, and 13 nm in diameter for ∼ 100%, ∼ 65% and ∼ 7% engine thrust, respectively) could be a concern for human health and the environment and merit further study. This work further emphasizes the significance of the detailed morphological characteristics of soot for assessing environmental impacts.
Read moreOptimum Pressure Ratio in a Turbojet Engine: Mathematical Expression to Determine the Pressure Ratio Required for Optimization of the Specific Thrust
With the resurgence of interest in blended wing body aircraft, flight test vehicles are being designed to perform scaled model testing of the concept. Consequently, there is a demand for high-efficiency turbojet engines in the sub-1000 N-thrust range. Since very few engines have been manufactured specifically for these flight test vehicles, RC scale/hobby engines have been the solution of choice. These engines are famously known for their low efficiency; therefore, further improvement is required. The pressure ratio of a turbojet engine plays a major role in its efficiency and performance. The effects of pressure ratio have been explored fairly extensively and often require an iterative process because of the complexity of the equations and the number of variables. This publication investigates the derivation of a mathematical expression to determine the optimum pressure ratio to maximize the specific thrust of a turbojet engine. Mathematical expressions in place of iterative processes accelerate the time it takes to perform an optimization. Mathematical expressions for the optimum total pressure across the compressor to maximize the specific thrust are developed for two scenarios. In the first scenario, the engine components, including the compressor, combustor, and turbine, are assumed to possess isentropic efficiencies of one hundred percent. In the second scenario, these efficiencies are not assumed to be perfect, and a pressure loss exists across the combustor. These expressions are obtained by differentiating the net specific thrust with respect to the total compressor pressure ratio. The results are validated by calculating the net specific thrust for varying pressure ratios and then manually identifying the optimum value. The results of this exercise serve as a starting point for selecting total compressor pressure ratios in a clean sheet turbojet design.
Read moreA sensitivity study on the starting simulations of turbojet engines
Gas turbine engine starting models require a lot of calibration to represent reality with acceptable accuracy due to the lack of high-quality component rig data in the sub-idle region. A detailed sensitivity study is presented in this paper to guide such calibration efforts. A thermodynamic component-matching type transient model of a single-spool turbojet engine with shaft and heat-soakage dynamics is employed for this purpose. Turbomachinery component maps are extended to sub-idle using an in-house map smoothing tool and the strategies presented by Kurzke recently. These extension strategies make use of the correlations hidden in the already available regions of the maps and ensure physical consistency. However, they contain some uncertainty, even when an experimentally obtained zero-speed line is available. Combustor sub-idle efficiency, stability limits, and delay are taken from the literature. Due to the chaotic nature of a combustor in the sub-idle region, a precise prediction of the combustor efficiency seems impossible. Effects of uncertainties related to sub-idle turbomachinery map extensions, burner efficiency, and heat soakage are investigated in this paper. Two popular fuel control strategies are employed and compared to see how controls deal with these uncertainties. It is concluded that turbomachinery torque characteristics and turbine capacities are the most important parameters when calibrating a starting model with a control based on rotational acceleration while burner efficiency and heat soakage are added on top of these with a control based on fuel flow rate.
Read moreAerodynamic Stability Study of Turbojet Engine During Unmanned Aerial Vehicle Assisted Taking Off Stage
Rocket Assisted Take Off (RATO) technology is utilized for the takeoff phase of various types of UAVs. RATO creates heavy axial overload for a UAV system, which consequently increases the inlet pressure of the fuel pump of the UAV’s turbojet engine. This situation leads to an abrupt change in fuel supply for its combustor, eventually causing drastic changes in the operating state of the compressor system. In addition, it may potentially induce compressor surge. To resolve this problem, through an experimental investigation, this study delves into the dynamic response of the fuel system during the RATO phase. A two-zone dual-wave coupled compressor model has been established for the intake-turbojet engine system to scrutinize the aerodynamic stability of the turbojet engine during the RATO phase. The findings reveal that when the increase of fuel pump inlet pressure causes changes in the fuel flow rate, it is essential for the engine to re-establish aerodynamic equilibrium in order to mitigate the impacts of abrupt fuel flow step increases. Moreover, it has been observed that the more the ratio of the length of the intake and the cross-section area, the greater the contribution of the inertial force of airflow in the pipe it brings within the passage. This results in a stronger suppression of combustion chamber pressure and flow rate fluctuations induced by fuel step supply, thereby rendering the compressor less susceptible to surge. In summary, this research contributes valuable insights for appropriate matching of intakes, enhancing the ability of the turbojet engine against fuel step supply in the combustion chamber during the takeoff stage and augmenting the aerodynamic and thermodynamic overload resistance capability of the engine.
Read moreRecent developments in turbomachinery component materials and manufacturing challenges for aero engine applications
In the recent years the development of turbomachinery materials performance enhancement plays a vital role especially in aircraft air breathing engines like turbojet engine, turboprop engine, turboshaft engine and turbofan engines. Especially the transonic flow engines required highly sophisticated materials where it can sustain the entire thrust which can create by the engine. The main objective of this paper is to give an overview of the present cost-effective and technological capabilities process for turbomachinery component materials. Especially the main focus is given to study the Electro physical, Photonic additive removal process and Electro chemical process for turbomachinery parts manufacture. The aeronautical propulsion based technologies are reviewed thoroughly where in surface reliability, geometrical precession, and material removal and highly strengthened composite material deposition rates usually difficult to cut dedicated steels, Titanium and Nickel based alloys. In this paper the past aeronautical and propulsion mechanical based manufacturing technologies, current sophisticated technologies and also future challenging material processing techniques are covered. The paper also focuses on the brief description of turbomachinery components of shaping process and coating in aeromechanical applications.
Read more