1 - Wood microstructure – A cellular composite

BackgroundThe mechanical properties of wood are largely determined by the orientation of cellulose microfibrils in secondary cell walls. Several genes and their allelic variants have previously been found to affect microfibril angle (MFA) and wood stiffness; however, the molecular mechanisms controlling microfibril orientation and mechanical strength are largely uncharacterised. In the present study, cDNA microarrays were used to compare gene expression in developing xylem with contrasting stiffness and MFA in juvenile Pinus radiata trees in order to gain further insights into the molecular mechanisms underlying microfibril orientation and cell wall mechanics.ResultsJuvenile radiata pine trees with higher stiffness (HS) had lower MFA in the earlywood and latewood of each ring compared to low stiffness (LS) trees. Approximately 3.4 to 14.5% out of 3, 320 xylem unigenes on cDNA microarrays were differentially regulated in juvenile wood with contrasting stiffness and MFA. Greater variation in MFA and stiffness was observed in earlywood compared to latewood, suggesting earlywood contributes most to differences in stiffness; however, 3-4 times more genes were differentially regulated in latewood than in earlywood. A total of 108 xylem unigenes were differentially regulated in juvenile wood with HS and LS in at least two seasons, including 43 unigenes with unknown functions. Many genes involved in cytoskeleton development and secondary wall formation (cellulose and lignin biosynthesis) were preferentially transcribed in wood with HS and low MFA. In contrast, several genes involved in cell division and primary wall synthesis were more abundantly transcribed in LS wood with high MFA.ConclusionsMicroarray expression profiles in Pinus radiata juvenile wood with contrasting stiffness has shed more light on the transcriptional control of microfibril orientation and the mechanical properties of wood. The identified candidate genes provide an invaluable resource for further gene function and association genetics studies aimed at deepening our understanding of cell wall biomechanics with a view to improving the mechanical properties of wood.

Correlating macroscopic plant growth parameters to nanomechanical properties of cellulose microfibrils

The structural aberrations of the cell walls of protophloem sieve elements (PSEs) in roots of wheat (Triticum aestivum L. cv. Maris Huntsman) caused by the anti-microtubule drug colchicine were investigated by electron microscopy. The initial effect of the drug on cell wall development was found to be an exceptionally rough wall surface, presumably caused by an uncontrolled fusion of Golgi vesicles with the plasma membrane. Cellulose microfibrils, which in normal PSEs are aligned transversely to the long axis and parallel to the cortical microtubules, in colchicine-treated PSEs display a predominant longitudinal orientation. The pattern of wall development is disturbed by deposition of wall material also within the sieve pores of the sieve-pore/plasmodesmata complexes, resulting in evenly thickened walls instead of the normal uneven layers, and in narrowing the sieve pores to the size of plasmodesmata. In prolonged and continuous colchicine treatment, PSEs develop unusual wall ingrowths projecting deeply into the cytoplasm, creating an extraordinary cell type not found in normal roots. The results confirm the view of microtubule involvement in the proper deposition and orientation of cellulose microfibrils, and in the normal patterning of the cell wall thickenings of differentiating PSEs.

The orientation of cellulose microfibrils (MFs) and the arrangement of cortical microtubules (MTs) in the developing tension-wood fibres of Japanese ash (Fraxinus mandshurica Rupr. var. japonica Maxim.) trees were investigated by electron and immunofluorescence microscopy. The MFs were deposited at an angle of about 45° to the longitudinal axis of the fibre in an S-helical orientation at the initiation of secondary wall thickening. The MFs changed their orientation progressively, with clockwise rotation (viewed from the lumen side), from the S-helix until they were oriented approximately parallel to the fibre axis. This configuration can be considered as a semihelicoidal pattern. With arresting of rotation, a thick gelatinous (G-) layer was developed as a result of the repeated deposition of parallel MFs with a consistent texture. Two types of gelatinous fibre were identified on the basis of the orientation of MFs at the later stage of G-layer deposition. Microfibrils of type 1 were oriented parallel to the fibre axis; MFs of type 2 were laid down with counterclockwise rotation. The counterclockwise rotation of MFs was associated with a variation in the angle of MFs with respect to the fibre axis that ranged from 5° to 25° with a Z-helical orientation among the fibres. The MFs showed a high degree of parallelism at all stages of deposition during G-layer formation. No MFs with an S-helical orientation were observed in the G-layer. Based on these results, a model for the orientation and deposition of MFs in the secondary wall of tension-wood fibres with an S1 + G type of wall organization is proposed. The MT arrays changed progressively, with clockwise rotation (viewed from the lumen side), from an angle of about 35–40° in a Z-helical orientation to an angle of approximately 0° (parallel) to the fibre axis during G-layer formation. The parallelism between MTs and MFs was evident. The density of MTs in the developing tension-wood fibres during formation of the G-layer was about 17–18 per μm of wall. It appears that MTs with a high density play a significant role in regulating the orientation of nascent MFs in the secondary walls of wood fibres. It also appears that the high degree of parallelism among MFs is closely related to the parallelism of MTs that are present at a high density.

The growing plant cell wall is commonly considered a fiber-reinforced structure whose strength, extensibility and anisotropy depend on the orientation of crystalline cellulose microfibrils, their bonding to the polysaccharide matrix, and matrix viscoelasticity1–4. Structural reinforcement of the wall by stiff cellulose microfibrils is central to contemporary models of plant growth, mechanics, and meristem dynamics4–12. Although passive microfibril reorientation during wall extension has been inferred from theory and from bulk measurements13–15, nm-scale movements of individual microfibrils have not been directly observed. Here we combined nm-scale imaging of wet cell walls by atomic force microscopy (AFM) with a stretching device and endoglucanase treatment that induces wall stress relaxation and creep, mimicking wall behaviors during cell growth. Microfibril movements during forced mechanical extensions differ from those during creep of the enzymatically-loosened wall. In addition to passive angular reorientation, we observed a diverse repertoire of microfibril movements that reveal the spatial scale of molecular connections between microfibrils. Our results show that wall loosening alters microfibril connectivity, enabling microfibril dynamics not seen during mechanical stretch. These insights into microfibril movements and connectivities need to be incorporated into refined models of plant cell wall structure, growth and morphogenesis.

Following a 5 hours ethylene treatment, cortical cells of Pea (Pisum sativum L. var Alaska) epicotyl third internode showed a change in the orientation of both microtubules near the plasma membrane and recently deposited cellulose microfibrils. Control cortical cells had mostly transverse microtubules. The ratio of the average frequency of transverse to longitudinal microtubules was 6.0. After 5 hours of ethylene treatment, cortical cells had mostly longitudinal microtubules, with the ratio of transverse to longitudinal microtubules equal to 0.1. Epidermal cells were more variable than cortical cells with regard to the frequency of longitudinal and transverse microtubules. Observation of cortical cell walls in conventionally stained thin sections revealed that recent deposition of microfibrils had been primarily transverse in almost all of the control cortical cells sampled. In contrast, more than half of the ethylene-treated cortical cells had recent deposition oriented primarily longitudinally. This change in microtubule and microfibril orientation may be early enough to constitute the primary effect of ethylene leading to radial cell expansion.

The cellulose microfibril assemblies in secondary cell walls of tension wood and compression wood were studied with vibrational sum frequency generation (SFG) spectroscopy. The tension wood contains the gelatinous layer with highly-crystalline and highly-aligned cellulose microfibrils. The SFG spectral features of tension wood changed depending on the azimuth angle between the polarization of the incident IR beam and the preferential alignment axis of the cellulose microfibrils. The SFG spectra of the compression wood did not show any dependence on the azimuth angle, implying that the overall orientation of cellulose microfibrils in compression wood is not highly aligned. Instead, the decrease of cellulose content in compression wood brought about larger separation between cellulose microfibrils, which was manifested as changes in CH2/OH intensity ratio in SFG spectra. These results implied that SFG spectral features are sensitive to cellulose microfibril alignments and inter-fibrillar separations.

Nanoindentation test has been performed to characterize the mechanical properties of aluminium alloy foam cell wall. Two of the mechanical properties: hardness and Young’s modulus of cell wall material were evaluated using the stiffness of contact during both loading and unloading. Properties obtained from unloading stiffness were in better agreement with the conventional test result than those obtained from loading stiffness. The finite element analysis using nonlinear finite element code ABAQUS was performed to characterize the yield strength and the stress-strain curve of the cell wall material of the foam. Properties of foam cell wall material were found to be substantially different from the properties of the material before foaming. The methodology used in this paper can be effectively used to characterize the mechanical properties of cell wall of any cellular material.

Plant development results from controlled cell divisions, structural modifications, and reorganizations of the cell wall. Thereby, regulation of cell wall behaviour takes place at multiple length scales involving compositional and architectural aspects in addition to various developmental and/or environmental factors. The physical properties of the primary wall are largely determined by the nature of the complex polymer network, which exhibits time-dependent behaviour representative of viscoelastic materials. Here, a dynamic nanoindentation technique is used to measure the time-dependent response and the viscoelastic behaviour of the cell wall in single living cells at a micron or sub-micron scale. With this approach, significant changes in storage (stiffness) and loss (loss of energy) moduli are captured among the tested cells. The results reveal hitherto unknown differences in the viscoelastic parameters of the walls of same-age similarly positioned cells of the Arabidopsis ecotypes (Col 0 and Ws 2). The technique is also shown to be sensitive enough to detect changes in cell wall properties in cells deficient in the activity of the chromatin modifier ATX1. Extensive computational modelling of the experimental measurements (i.e. modelling the cell as a viscoelastic pressure vessel) is used to analyse the influence of the wall thickness, as well as the turgor pressure, at the positions of our measurements. By combining the nanoDMA technique with finite element simulations quantifiable measurements of the viscoelastic properties of plant cell walls are achieved. Such techniques are expected to find broader applications in quantifying the influence of genetic, biological, and environmental factors on the nanoscale mechanical properties of the cell wall.

Based on precise information about the orientations of cellulose microfibrils (CMFs) in the secondary cell wall of theEquisetum hyemale root hair, a geometrical model was recently put forward to account for the deposition orientation of CMFs. The model supposes that synthases spin out the CMFs and that geometrical laws dictate their movement. Taking space-limiting conditions into account, CMF orientation is dependent on cell morphology, the amount of other wall molecules adhering to the CMFs, and the number and distribution pattern of synthases. In the present paper this geometrical model for CMF deposition is further applied to nontip-growing angular cells with varying diameters, cells with tapering morphology, various distribution patterns of synthases, various matrix/fibril ratios, and intercalarily elongating cells. The model can accurately predict the actual wall textures in a great variety of cell walls. In the proposed model for CMF orientation, microtubules are not required as cellular guiding structures for the CMFs, not even in elongating walls. They are supposed to be involved in cell elongation, possibly by delivering wall material including CMF synthases.

In this review, I ask the question of what is the relationship between growth and the orientations of microtubules and cellulose microfibrils in plant cells. This should be a relatively simple question to answer considering that text books commonly describe microtubules and cellulose microfibrils as hoops that drive expansion perpendicular to their orientation. However, recent live imaging techniques, which allow microtubules and cellulose synthase dynamics to be imaged simultaneously with cell elongation, show that cells can elongate with nonperpendicular microtubule arrays. In this review, I look at the significance of these different microtubule arrangements for growth and cell wall architecture and how these resultant walls differ from those derived from perpendicular arrays. I also discuss how these divergent arrays in stems may be important for coordinating growth between the different cell layers. This role reveals some general features of microtubule alignment that can be used to predict the growth status of organs. In conclusion, nonperpendicular arrays demonstrate alternative ways of cell elongation that do not require hooped arrays of microtubules and cellulose microfibrils. Such nonperpendicular arrays may be required for optimal growth and strengthening of tissues.

SummaryGuard cells dynamically adjust their shape in order to regulate photosynthetic gas exchange, respiration rates and defend against pathogen entry. Cell shape changes are determined by the interplay of cell wall material properties and turgor pressure. To investigate this relationship between turgor pressure, cell wall properties and cell shape, we focused on kidney‐shaped stomata and developed a biomechanical model of a guard cell pair. Treating the cell wall as a composite of the pectin‐rich cell wall matrix embedded with cellulose microfibrils, we show that strong, circumferentially oriented fibres are critical for opening. We find that the opening dynamics are dictated by the mechanical stress response of the cell wall matrix, and as the turgor rises, the pectinaceous matrix stiffens. We validate these predictions with stomatal opening experiments in selected Arabidopsis cell wall mutants. Thus, using a computational framework that combines a 3D biomechanical model with parameter optimization, we demonstrate how to exploit subtle shape changes to infer cell wall material properties. Our findings reveal that proper stomatal dynamics are built on two key properties of the cell wall, namely anisotropy in the form of hoop reinforcement and strain stiffening.

Plant cell shape is determined by the orientation of cellulose microfibrils in the primary cell wall. Consequently, mutations that affect genes encoding the enzymes responsible for the synthesis of cellulose, namely, the cellulose synthase catalytic subunits, can alter cell shape substantially, particularly in the roots of affected plants. The multiple response expansion1 (mre1) mutant of Arabidopsis thaliana results from a point mutation in the AtCESA3 gene, which encodes one of the three isoforms of the cellulose synthase catalytic subunit required for synthesis of cellulose in the primary cell wall. Phenotypic comparison of the mre1 mutant with three other alleles (ectopic lignification1-1, ectopic lignification1-2 and constitutive expression of vsp1) showed that these four alleles form an allelic series with respect to their root phenotypes, with mre1 being the weakest allele identified to date. These analyses demonstrated that sucrose affects a significant alteration of cell shape in the roots of these mutants and likely suppresses root cell division in them as well, and that the chemical aminoisobutyric acid can suppress these effects of sucrose. Interestingly, the cell walls in the roots of these four AtCESA3 alleles contain different percentages of cellulose, and these percentages correlate with the lengths of the roots and cortex cells in these roots when grown on media containing high levels of sucrose.

Recent advances in our understanding of the molecular control of secondary cell wall (SCW) formation have shed light on molecular mechanisms that underpin domestication traits related to wood formation. One such trait is the cellulose microfibril angle (MFA), an important wood quality determinant that varies along tree developmental phases and in response to gravitational stimulus. The cytoskeleton, mainly composed of microtubules and actin filaments, collectively contribute to plant growth and development by participating in several cellular processes, including cellulose deposition. Studies in Arabidopsis have significantly aided our understanding of the roles of microtubules in xylem cell development during which correct SCW deposition and patterning are essential to provide structural support and allow for water transport. In contrast, studies relating to SCW formation in xylary elements performed in woody trees remain elusive. In combination, the data reviewed here suggest that the cytoskeleton plays important roles in determining the exact sites of cellulose deposition, overall SCW patterning and more specifically, the alignment and orientation of cellulose microfibrils. By relating the reviewed evidence to the process of wood formation, we present a model of microtubule participation in determining MFA in woody trees forming reaction wood (RW).

The anisotropic growth of plant cells depends on cell walls having anisotropic mechanical properties, which are hypothesized to arise from aligned cellulose microfibrils. To test this hypothesis and to identify genes involved in controlling plant shape, we isolated mutants in Arabidopsis thaliana in which the degree of anisotropic expansion of the root is reduced. We report here the characterization of mutants at two new loci, RADIALLY SWOLLEN 4 (RSW4) and RSW7. The radial swelling phenotype is temperature sensitive, being moderate (rsw7) or negligible (rsw4) at the permissive temperature, 19 degrees C, and pronounced at the restrictive temperature, 30 degrees C. After transfer to 30 degrees C, the primary root's elongation rate decreases and diameter increases, with all tissues swelling radially. Swelling is accompanied by ectopic cell production but swelling is not reduced when the extra cell production is eliminated chemically. A double mutant was generated, whose roots swell constitutively and more than either parent. Based on analytical determination of acid-insoluble glucose, the amount of cellulose was normal in rsw4 and slightly elevated in rsw7. The orientation of cortical microtubules was examined with immunofluorescence in whole mounts and in semi-thin plastic sections, and the orientation of microfibrils was examined with field-emission scanning electron microscopy and quantitative polarized-light microscopy. In the swollen regions of both mutants, cortical microtubules and cellulose microfibrils are neither depleted nor disoriented. Thus, oriented microtubules and microfibrils themselves are insufficient to limit radial expansion; to build a wall with high mechanical anisotropy, additional factors are required, supplied in part by RSW4 and RSW7.