1A1-I13 受動要素を利用したロボットのインピーンダンス制御系の構成 : シミュレーションを用いた安定性に関する一考察(感覚・運動・計測)

This paper considers a power assist system of elbow as an example of human-assist system and describes impedance control of it. The assist system is required not only to assist the movement of elbow but also to be strictly stable. Impedance control based on position control is often used for the assist devices because the control system is simpler than that of the devices based on force control. But if the impedance parameters are made to be small in order to get good maneuverability, the system becomes unstable because of the delay of the position control system especially when the assisted tool touches high stiffness environment such as a wall. So, an impedance control method based on position control with passive elements is proposed. As a result, the stability and the effects on time delay of the proposed system showed good performance.

This paper proposes an intelligent massage control system by using multi-fingered robot hand with hybrid impedance and force control, which is able to create the movement and force of robot to behave as similar as the human’s massage. Therefore, the various massage points, such as the changing of hardness and softness of human skin muscle condition, can be appropriately controlled by using hybrid impedance and force control method. The impedance control is used to control the lateral position of massage on the human skin muscle. The perpendicular direction one, while force control is carried out for the vertical direction on human skin muscle. This paper also gives a modeling of human skin muscle through robot perception of impedance to decide the parameter of impedance controller. The control strategy using a hybrid impedance and force control to implement an adaptive control system is presented, when human condition is changed with soft and hard skin muscle. For the robot fingertip force, PI servo compensation is used together with impedance control. Based on using both impedance and PI servo compensation, the effectiveness of the massage position and force control is shown through actual massage motion experiments.

The best exoskeleton control strategy depends on the task, motivating the development and analysis of an exoskeleton capable of position, force, and impedance control. In this paper, we implement and compare the three controller types via sliding mode control on a custom-built pneumatic cylinder ankle exoskeleton. To evaluate each controller's performance, the exoskeleton was tested on the benchtop and with human subject experiments. With the position controller, the exoskeleton achieved an root-mean-square error (RMSE) of under 5 deg for both the benchtop and human tests. It had a bandwidth of approximately 12 rad/s. The force controller tracked sinusoidal trajectories acceptably well at low frequencies (15% of force range at 6 rad/s), with a bandwidth of approximately 24 rad/s. The error was significantly higher (RMSE of 24% of force range) for the more biologically relevant trajectory. The impedance controller demonstrated the desired spring-like behavior, with position RMSE generally under 5 deg compared to expected position. All three controllers worked equally well for benchtop and human tests. Thus, a pneumatically powered ankle exoskeleton with sliding mode control is capable of accurate position and impedance control and is capable of marginally acceptable force control.

On-line learning of robot arm impedance using neural networks

In this paper, a novel impedance control method is designed for the hydraulic drive unit (HDU) equipped on the hydraulic driven legged robot. First, the position control mathematical model of HDU is built. Next, the HDU performance test platform is introduced and the performance requirements are given. Second, the system load pressure observer is designed and an accurate stiffness control method is proposed by combining the external load force feed forward control with the load force feedback control. Third, the damping control method based on the velocity feedback is designed. Finally, a novel impedance control method is proposed through combining the stiffness control and the damping control. The effects of all techniques listed above have been verified experimentally. Especially, the impedance control effects are verified by comparing the impedance characteristics with the natural characteristics of the second-order mass-spring-damper system. This research indicates that the system characteristics of HDU with the novel impedance control method is well equivalent to that of the second-order mass-spring-damper system, which can solve the stall problem of the robot joint movement process caused by the load force vanish instantaneously and the switch between position control and force control. The above research can provide references for the active compliance control of bionic legged robots.

In this paper, model-based precision force and position control of an ionic polymer metal composite (IPMC) is presented. A 23.8 mm × 3.4 mm × 0.16 mm IPMC strip was used as an actuator in a cantilever configuration. Open-loop force and position responses of an IPMC are not repeatable, and hence closed-loop precision control is of critical importance to ensure proper functioning, repeat-ability and reliability. After feedback controllers were designed and implemented with empirically obtained fourth-order plant transfer functions, the overshoot decreased from 460 to 2.8 per cent and the settling time was reduced from 37.5 to 3.22 s in force control. In position control the overshoot decreased from 333 to 20.3 per cent and the settling time was reduced from 21.5 to 2.56 s. Microscale precision force and position control capabilities of the IPMC actuator were also demonstrated experimentally. An 8 μN force resolution was achieved with a force noise of 0.5μN r.m.s., and the position resolution was 6 μm with a position noise of 2.5 μm r.m.s. The maximum force and tip displacement achieved with the IPMC actuator under closed-loop control were 2 mN and 5 mm respectively. The IPMC actuator could follow various commanded force and position trajectories such as sinusoidal and trapezoidal position profiles, and a velocity profile with a 3 mm/s maximum velocity. A novel hybrid force and position control strategy demonstrated its utility in practical micromanipulalion applications where the actuator force must be limited to prevent damaging micro-objects. High-precision control of the IPMC at low force level proved its potential for micromanufacturing and micromanipulation applications such as robotic and biomedical microgrippers.

Physiotherapy is the treatment to recover a patient’s mobility and limb function after an injury, illness, or disability. Rehabilitation robots can be used to replace human physiotherapists. To ensure safety during robot physical therapy, the patient’s limb needs to be controlled to track a desired joint trajectory, and the torque due to interaction force/torque needs to be measured and regulated. Therefore, hybrid impedance and admittance with position control (HIPC) is required to track the trajectory and simultaneously regulate the contact torque. The literature describes two structures of HIPC: (1) a switched framework between admittance and impedance control operating in parallel (HIPCSW); and (2) a series connection between admittance and impedance control without switching. In this study, a hybrid adaptive impedance and position-based admittance control (HAIPC) in series is developed, which consists of a proportional derivative-based admittance position controller with gravitational torque compensation and an adaptive impedance controller. An extended state observer is used to estimate the interaction joint torque due to human stiff contact with the exoskeleton without the use of force/torque sensor, which is then used in the adaptive algorithm to update the stiffness and damping gains of the adaptive impedance controller. Simulation results obtained using MATLAB show that the proposed HAIPC significantly reduces the mean absolute values of the actuation torques (control inputs) required for the shoulder and elbow joints in comparison with HIPC and HIPCSW.

일반 산업용 로봇의 위치정밀도는 100㎛ 정도임에 반해, 정밀부품의 조립공차는 수십 ㎛ 이내이다. 또한, 조립공차가 작을 경우 미소한 위치/각도 오차에 의해 재밍 또는 웨징이 쉽게 발생하며, 위치제어 기반의 로봇인 경우 부품 조립 시 접촉력을 적절히 조절하지 못하여 조립물이 파손될 가능성이 크다. 이와 같은 문제를 해결하기 위하여 접촉력에 능동적으로 반응할 수 있는 힘제어 기반의 로봇조립에 대한 연구가 진행되고 있다. 본 연구에서는 기존의 산업용 로봇에 적용하기 용이하도록 위치제어 기반의 머니퓰레이터에 힘제어를 적용할 수 있는 시스템을 구현하였다. 머니퓰레이터에 어드미턴스 필터를 이용한 임피던스 제어를 적용하여 안정적인 접촉운동을 구현하였다. 또한, 임피던스 제어와 blind 검색을 적용하여 정밀부품을 조립할 수 있음을 검증하였다.

This paper proposes an intelligent massage control system by using multi-fingered robot hand with hybrid impedance control, which is able to create the movement and the force of robot such as the human's massage. Therefore, the various massage points, such as the change of the stiffness of human skin muscle, can be controlled by using impedance control method. The hybrid impedance control is comprised of the two methods of the position-based and the force-based impedance control were applied. The position-based impedance control is used to control the lateral position of massage on the human skin muscle. On the other hand, the force-based impedance control is used to control the force of the vertical direction on human skin muscle. This paper also gives the identification of human skin muscle through robot perception of impedance to decide the parameter of impedance controller. The control strategy using impedance control to implement an adaptive control system is presented, when human condition is changed with soft and hard skin muscle. Effectiveness of massage control system by using multi- fingered robot hand with hybrid impedance control is demonstrator through actual massage experiments of pushing and rubbing motion.

To address the demands for precision and load-bearing capacity in the installation of building panels, a hybrid force-position driven robot with redundant actuation has been developed. The mechanical performance of this robot is primarily governed by its central parallel mechanism, which is equipped with redundant actuators matching the degrees of freedom. Non-redundant and redundant actuators are respectively responsible for position and force control. The inclusion of redundant force-driven joints has increased the internal coupling within the mechanism. To enhance the coordination between position and force control, a hybrid synchronized control method based on cross-coupling has been proposed. Initially, kinematic and dynamic models of the parallel structure were established. Under predefined trajectories, the theoretical inputs for each actuator were calculated using inverse kinematics and dynamics. Subsequently, employing the principle of cross-coupling, the torque output from the position actuators was used as feedback. This feedback was processed by a synchronized coordination controller to adjust the output force of the redundant force-driven joints. By adjusting the output force of the redundant actuators, the torque burden on the position actuators was effectively reduced, thereby enhancing the precision of position control. Additionally, under the same load conditions, smaller power actuators could be utilized for position control, reducing the overall weight of the robot and improving its load-to-weight ratio. To validate the effectiveness of the proposed control strategy, a robotic simulation environment was established. The simulation results demonstrated significant reductions in the average torque required by the position actuators across three different trajectories, with reductions of 91.43%, 54.56%, and 80.6% respectively. Finally, the load-bearing capacity and the load-to-weight ratio of the prototype were assessed. Experimental results confirmed that the prototype achieved a load-to-weight ratio of 15.83%, validating the effectiveness of the hybrid synchronized control method based on cross-coupling.

This paper presents an interconnection and damping assignment passivity based control (IDA-PBC) for the position and impedance control of flexible joint robot. In considering of the joint damping and with some simplification of friction, a flexible joint robot system is descripted as an port-controlled Hamiltonian system with dissipation(PCHD). Then, giving a desired Hamiltonian function which both shapes potential and kinetic energies, the control laws of position control and impedance control is derived by the algebraic IDA-PBC method, which preserves the PCHD structure of the close-loop system. Comparing with the traditional passivity based control (PBC), the proposed method gives a new explanation of the control of flexible joint robot by introducing the self-damping and cross-damping terms, which make the gain selecting procedure more intuitive and comfortable. Simulation and experiments are done to verify the proposed controller, and the results shows a promising performance both in position and impedance control.

Precise force control and position control is essential for many robotic applications. During unilateral or bilateral object handling remote applications, human operators apply excess forces on the actuators with the intention of better grip and it is possible to damage the handled objects. This paper proposes position control and force control techniques when human applies excess force. The controllers consist of predefined force and equilibrium position which are correspond to remote environmental object safety. The operator applied excess force is modeled as a spring force through a virtual stiffness model. The paper introduces proportional derivative position control loop to conventional virtual stiffness controller. The force control loop and the position control loop references are combined in the common dimension of acceleration to produce current reference to the actuator. The sensorless sensing techniques of disturbance observer and reaction force observer are utilized to disturbance suppression and external force estimation. In the force controller, estimated reaction force is reduced to desired value by introducing virtual force loop between reaction force observer output and reaction force feedback input. The position control is achieved by introducing a scaling factor to reaction force feedback path. The switching between force control and position control is possible with scaling factor value. The performances of proposed methods are compared with conventional method and validity of the proposed methods is verified by simulations and experiments.

Automatic cell injection has been the focus of many researches and commercial development for several years. In this paper, a robotic cell injection system for automatic batch injection of suspended cells is developed. To facilitate the process, these suspended cells are held and fixed to a cell array by a specially designed cell holding device, and injected one by one through an “out-of-plane” cell injection process. A micropipette equipped with a PVDF micro force sensor is integrated in the proposed system. The force sensor is utilized to measure real time injection force applied to the cells during injection process. Through calibration of the relationship between the cell injection force and the desired injector pipette trajectory, a position (vision) and force control algorithm is proposed and applied to the motion control of the injection pipette in three-coordinate directions during an injection process. The out-of-plane cell injection task is decoupled into a position control in X-Y horizontal plane and an impedance force control in Z-axis. The depth motion of the injector pipette, a common problem of three-dimensional micromanipulation, is indirectly controlled by the force control. Finally, experimental results are given to demonstrate the effectiveness of the proposed approach.

Two different control schemes, position model referenced control (PMRC) and force model referenced control (FMRC), are developed for a simplified two robots model with one interacting axis. The dynamic stability of the position (or force) control under the FMRC (or PMRC) is analyzed. Results indicate that PMRC, although providing better dynamic performance of the position control, may degrade the dynamic performance of the force control. However, FMRC can provide better dynamic performance of both position and force control.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>

So far, a considerable amount of research has been devoted to flexible arms, especially to their modelling, position control and vibration control. Meanwhile very few research has addressed the problem of force control, since it is one of the most important functions of the robot tasks. In this paper, we present a two-degree-of-freedom control system for the force control of flexible cartesian robots. Use of a two-degree-of freedom control system guarantees the independent design of the feedforward and feedback control characteristics. The feedforward controller is designed using inverse dynamics, while the design of the stabilized feedback controller is achieved by Lyapunov's direct method. Numerical simulation and experimental results confirm that faster precise force control can be realized with the proposed control system.