- Single Book
- 10.1016/b978-0-7506-8857-4.x5001-8
Ophthalmic Imaging
- Jan 01, 2008
- Sandip Doshi + 2 more +2
Ophthalmic Imaging
A discrete component low-noise preamplifier readout for a linear (1×16) SiC photodiode array
Ophthalmic Imaging
Ophthalmic Imaging
Nonequilibrium and bolometric photoresponse in patterned YBa2Cu3O7−δ thin films
Epitaxial laser deposited YBa2Cu3O7−δ films of ∼50 nm thickness were patterned into detectors consisting of ten parallel 1 μm wide strips in order to study nonequilibrium and bolometric effects. Typically, the patterned samples had critical temperatures around 86 K, transition widths around 2 K and critical current densities above 1×106A/cm2 at 77 K. Pulsed laser measurements at 0.8 μm wavelength (17 ps full width at half maximum) showed a ∼30 ps response, attributed to electron heating, followed by a slower bolometric decay. Amplitude modulation in the band fmod=100 kHz–10 GHz of a laser with wavelength λ=0.8 μm showed two different thermal relaxations in the photoresponse. Phonon escape from the film (∼3 ns) is the limiting process, followed by heat diffusion in the substrate. Similar relaxations were also seen for λ=10.6 μm. The photoresponse measurements were made with the film in the resistive state and extended into the normal state. These states were created by supercritical bias currents. Measurements between 75 and 95 K (i.e., from below to above Tc) showed that the photoresponse was proportional to dR/dT for fmod=1 MHz and 4 GHz. The fast response is limited by the electron-phonon scattering time, estimated to 1.8 ps from experimental data. The responsivity both at 0.8 and 10.6 μm wavelength was ∼1.2 V/W at fmod=1 GHz and the noise equivalent power was calculated to 1.5×10−9 WHz−1/2 for the fast response.
Read moreVersatile active-only biquad circuits with loss-less and lossy integrators
This paper presents a realization of voltage-mode and current-mode active-only biquad circuits with a two-integrator loop-structure. The circuits are constructed solely with operational amplifiers (OAs) and operational transconductance amplifiers (OTAs). The biquad circuits can realize the multiple circuit transfer functions, and the circuit parameters can be tuned orthogonally through adjusting the transconductance gains of the OTAs. Also, these biquad circuits enjoy very low sensitivities with respect to the circuit active elements. Some examples are given together with simulated results by PSPICE. The circuit configurations are very suitable for implementation on both bipolar and CMOS technologies.
Read moreHigh Responsivity Mg<italic>x</italic>Zn1–<italic>x</italic>O Based Ultraviolet Photodetector Fabricated by Dual Ion Beam Sputtering
Mg <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">x</sub> Zn <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">1-x</sub> O (x = 0.05, 0.15 and 0.20) based metal-semiconductor-metal ultraviolet (UV) photodetectors were fabricated on Si substrate using dual-ion-beam sputtering. The performances of fabricated photodetectors were studied by current-voltage, spectral photoresponse, and temporal response measurements. The values of peak responsivity of photodetectors were 0.4, 0.31, and 0.27 A/W with corresponding external quantum efficiency of 146%, 110%, and 105% for x = 0.05, 0.15 and 0.20, respectively. The cutoff wavelength and UV/visible rejection ratio of fabricated photodetectors decrease over 360-330 nm and 341.8-115.3, respectively, with increase in Mg concentration. The variation in specific detectivity and noise equivalent power with Mg concentration variation is also reported.
Read moreA novel SWIR detector with an ultra-high internal gain and negligible excess noise
Short wave infrared (SWIR) imaging systems have several advantages due to the spectral content of the nightglow and better discrimination against camouflage. Achieving single photon detection sensitivity can significantly improve the image quality of these systems. However, the internal noise of the detector and readout circuits are significant barriers to achieve this goal. One can prove that the noise limitations of the readout can be alleviated, if the detector exhibits sufficiently high internal gain. Unfortunately, the existing detectors with internal gain have a very high noise as well. Here we present the recent results from our novel FOcalized Carrier aUgmented Sensor (FOCUS). It utilizes very high charge compression into a nano-injector, and subsequent carrier injection to achieve high quantum efficiency and high sensitivity at short infrared at room temperature. We obtain internal gain values exceeding several thousand at bias values of less than 1 volt. The current responsivity at 1.55 μm is more than 1500 A/W, and the noise equivalent power (NEP) is less that 0.5 x10<sup>-15 </sup>W/Hz<sup>1/2</sup> at room temperature. These are significantly better than the performance of the existing room temperature devices with internal gain. Also, unlike avalanche-based photodiodes, the measured excess noise factor for our device is near unity, even at very high gain values. The stable gain of the device combined with the low operating voltage are unique advantages of this technology for high-performance SWIR imaging arrays.
Read moreTerahertz (THz) direct detectors based on superconducting HEBs with thermal, THz and microwave biasing methods (Conference Presentation)
Superconducting hot electron bolometers (HEBs) are widely used as terahertz (THz) heterodyne detectors (mixers) and becoming the most advantageous candidate for low noise receiver at frequencies above 1.2 THz. However, there is still lack of accurate theoretical modeling which explains the complex mechanism of different aspects of superconducting HEBs. These difficulties do not prevent researchers around the world from making experimental progress. In the last few years, superconducting HEBs are also used as THz direct detectors to develop the array for the applications in biology, medicine and security systems. Recently, a noise equivalent power (NEP) of 0.2 pW/√Hz at 2.5 THz is reported for the superconducting HEBs with thermal biasing. Instead of thermal one, microwave (MW) which was first used to stabilize the HEB mixer is also applied to bias the device as a direct detector. Furthermore, THz can be used to bias the HEBs, if THz sources can be provided easy. Although MW biasing can improve sensitivity of the superconducting HEB direct detectors, little work has been done to compare the responsivity and NEP among the THz direct detectors with thermal, THz and MW biasing. To find a best biasing method, we have studied the similarities and differences of the direct detectors based on the superconducting HEBs with three different biasing methods. The fabricated NbN HEB detectors consist of a complementary logarithmic-spiral antenna made of gold and an NbN film (bridge) connecting across the antenna's inner terminals. We have fabricated the niobium nitride (NbN) superconducting HEB mixers with the system double sideband (DSB) noise temperature better than 8 times of the quantum limit: hf/kB (where h is the Planck constant, kB is the Boltzmann constant and f is the operating frequency) at the frequencies higher than 1 THz. Here, the mixer chips with the system DSB noise temperature of about 400 K and the intermediate frequency (IF) gain bandwidth (GBW) of larger than 5 GHz at 4.2 K and 0.65 THz have been used. As the direct detectors, the current responsivity of 290 A/W and 105 A/W are obtained for MW and THz biasing, which about one order higher than that of thermal biasing. The NEP of 2.7 pW/√Hz is obtained with MW biasing, which can be expected to be improved in the future.
Read moreOn the Sizing of CMOS Operational Amplifiers by Applying Many-Objective Optimization Algorithms
In CMOS integrated circuit (IC) design, operational amplifiers are one of the most useful active devices to enhance applications in analog signal processing, signal conditioning and so on. However, due to the CMOS technology downscaling, along the very large number of design variables and their trade-offs, it results difficult to reach target specifications without the application of optimization methods. For this reason, this work shows the advantages of performing many-objective optimization and this algorithm is compared to the well-known mono- and multi-objective metaheuristics, which have demonstrated their usefulness in sizing CMOS ICs. Three CMOS operational transconductance amplifiers are the case study in this work; they were sized by applying mono-, multi- and many-objective algorithms. The well-known non-dominated sorting genetic algorithm version 3 (NSGA-III) and the many-objective metaheuristic-based on the R2 indicator (MOMBI-II) were applied to size CMOS amplifiers and their sized solutions were compared to mono- and multi-objective algorithms. The CMOS amplifiers were optimized considering five targets, associated to a figure of merit (FoM), differential gain, power consumption, common-mode rejection ratio and total silicon area. The designs were performed using UMC 180 nm CMOS technology. To show the advantage of applying many-objective optimization algorithms to size CMOS amplifiers, the amplifier with the best performance was used to design a fractional-order integrator based on OTA-C filters. A variation analysis considering the process, the voltage and temperature (PVT) and a Monte Carlo analysis were performed to verify design robustness. Finally, the OTA-based fractional-order integrator was used to design a fractional-order chaotic oscillator, showing good agreement between numerical and SPICE simulations.
Read moreAn error rate improvement of decision feedback equalization by extraordinary level detection
Decision feedback equalization, which uses extraordinary level detection (Ex-DFE), with two feedback loops in parallel, is a detection technique which achieves not only significant error rate improvements but also detecting performance of burst-errors. As extraordinary level detection does not use any constraint on channel codes, Ex-DFE is effective for both runlength limited codes with minimum runlength parameters d=0 and d=1. The simple implementation, which contains no high-accuracy A/D convertor or Viterbi detector, is suggested.
Read moreNew circuit configuration for fast, stable and noise free MOSFET IC superior operational amplifier
The paper defines the limitations and point of weakness of already known and realized MOSFET operational amplifiers. The noticeable delay, poor slew rate, serious noise and low gain are examples of these drawbacks, which have been revealed to be related to bad circuit technique or poor technology of fabrication. A new and powerful circuit configuration comprising noise, offset, drift compensation and speeding up techniques for a superior MOSFET IC operational amplifier. The simulated results showed a very good performance improvement (slew rate SR=10/sup 4/V//spl mu/sec, delay time t/sub d//spl sim/10/sup -11/ sec, noise power reduction e/sub n//spl sim/54 dB, e/sub off//spl sim/50 /spl mu/V, distortion D/spl sim/25 nV/C/spl deg/).
Read moreAn analog front-end bipolar-transistor integrated circuit for the SDC silicon tracker
A low-noise, low-power, high-bandwidth, radiation hard, silicon bipolar-transistor full-custom integrated circuit (IC) containing 64 channels of analog signal processing has been developed for the SDC silicon tracker The IC was designed and tested at LBL and was fabricated using AT&T's CBIC-U2, 4 GHz f/sub /spl tau// complementary bipolar technology. Each channel contains the following functions: low-noise preamplification, pulse shaping and threshold discrimination. This is the first iteration of the production analog IC for the SDC silicon tracker. The IC is laid out to directly match the 50 /spl mu/m pitch double-sided silicon strip detector. The chip measures 6.8 mm/spl times/3.1 mm and contains 3,600 transistors. Three stages of amplification provide 180 mV/fC of gain with a 35 nsec peaking time at the comparator input. For a 14 pF detector capacitance, the equivalent noise charge is 1300 el. RMS at a power consumption of 1 mW/channel from a single 3.5 V supply. With the discriminator threshold set to 4 times the noise level, a 16 nsec time-walk for 1.25 to 10 fC signals is achieved using a time-walk compensation network. Irradiation tests at TRIUMF to a /spl Phi/=10/sup 14/ protons/cm/sup 2/ have been performed on the IC, demonstrating the radiation hardness of the complementary bipolar process. >
Read moreSensitive Continuous-Wave Terahertz Detection by Resonant-Tunneling-Diode Oscillators
We have characterized the sensitivity and noise equivalent power (NEP) of resonant-tunneling-diode (RTD) oscillators as terahertz (THz)-wave detectors. Using a continuous-wave (CW) frequency-tunable THz-wave photomixer source, we observed that sensitive detection was achieved by RTD oscillators around its oscillation frequencies. The quasi-optical RTD device oscillating at 0.78 THz showed a maximum current responsivity of 7.3 A/W near the peak point of the negative differential conductance (NDC) region and a minimum NEP of 7.7 pW/√Hz within the NDC region, respectively, at room temperature.
Read moreSome Interrelationships between the First and Second Synaptic Regions of the Fly’s (Musca domestica L.) Visual System
Electron microscopy of Golgi impregnated neurons has allowed the precise determination of the spatial relationships between identifiable profiles in optic cartridges and corresponding terminals in the medulla columns. Golgi-E.M. profiles can be correlated with profiles in normal electron microscopy. Structural contacts of cells in the lamina as well as their corresponding components in the medulla are described: functional contacts (synapses) known up to the present time are listed in figure 5 (polarities arrowed). Possibly structural contact may be indicative of functional intimacy, but this is still to be determined. At least three centripetal pathways (L1, L2, L3) convay information from R1 — R6 into the medulla. The other monopolars L4 and L5 appear to be intimate with endings of centrifugal cells from the medulla. The logic underlying the complexity of lamina organization seems to lie in the arrangement of feed-back and feed forward loops in parallel with the centripetal cells.
Read moreChapter 8 - Broadband Class-E
Chapter 8 - Broadband Class-E
Tantalum Thin-Film RC Circuit Technology for a Universal Active Filter
This paper describes the physical layout, process sequence, and component properties of a universal active filter designated the standard tantalum active resonator (STAR). This active-filter building block was realized as a hybrid integrated circuit (HIC) using tantalum thin-film technology. Several different circuit configurations are possible using only one set of process photomasks and one HIC. This can be accomplished by a wide range of precise resistor values through the use of laser trimming and various interconnecting schemes for the components on the HIC via the printed wiring board. The STAR circuit is comprised of nine laser-adjustable tantalum thin-film resistors totalling a maximum of 1 M \Omega , two 5100-pF tantalum capacitors, and one operational amplifier. The capacitors are formed by anodizing tantalum to 190 V and depositing NiCr-Pd-Au as the adherent counterelectrode. The resistors are made from 300- \Omega / \Box$^b$ tantalum oxynitride film which is preaged at 350°C for 1 h. The single-substrate RC process is amenable to batch processing and precision tuning, making it attractive for high-level production of precision filters. New thin-film design criteria and process developments permitted this circuit to be fabricated on a 16-pin dual-inline package ceramic substrate which could be packaged for machine insertion with commercially available insertion equipment.
Read moreA high gain low offset amplifier with rail-to-rail inputs
To fit some applications like in Power Management IC (Integrated Circuit), ahigh gain low offset BiCMOS op amp was proposed in this paper. A complementary input stage was adopted to meet a rail-to-rail ICMR (Input Common-Mode Range). And a special circuit configuration was introduced into the rail-to-rail amplifier to keep its gain constant. Simulation showed that the variation of g m was maintained within 2% over the whole input range. Meanwhile, by using bipolar input stage and current compensating circuit, the offset voltage of the op amp was reduced to less than 0.5mV.
Read more