A DNN-based MIMO signal detector using transformer architecture for next-generation wireless networks

This paper investigates the performance of IEEE 802.11ac physical layer (PHY) when the following multiple input multiple output (MIMO) detectors are implemented: Sphere Decoding (SD); QRM-Maximum Likelihood (QRM-MLD); List Minimum Mean Squared Error Successive Interference Cancellation (List MMSE-SIC); List Zero-Forcing SIC (List ZF-SIC); Lattice Reduction MMSE-SIC (LR MMSE-SIC) and List LR MMSE-SIC. The conclusions are founded on simulation results, validated using first order techniques, over TGac channel models. The IEEE 802.11ac simulator implements hard-decision Viterbi decoding and realistic synchronization and channel estimation algorithms. The List MMSE-SIC scheme presents power gains around 2 dB in relation to the List ZF-SIC MIMO detector. The QRM-MLD MIMO detector has a highly superior performance regarding to the List MMSE-SIC MIMO detector since this latter scheme cannot overcome the propagation errors that degrade the performance of MMSE-SIC MIMO detectors. However, for moderate list lengths of 4 and 8, the QRM-MLD MIMO detector presents severe power losses in relation to the optimal SD MIMO detector. The LR MMSE-SIC MIMO detector allows power losses of only 1–2 dB in reference to the optimal SD MIMO receiver. There are no noticeable power gains when List detection techniques in MMSE-SIC MIMO detectors are implemented since the diversity gains due to implementation of LR basis change overcome the error propagation in SIC MIMO detectors with original channel basis.

After a few decades’ evolution of wireless communication systems, to ensure reliable highspeed communication over unreliable wireless channels is still one of the major challenges facing researchers and engineers. The use of multiple antennas at transmitter and receiver, known as multiple-input multiple-output (MIMO) communications, is one promising technology delivering desired wireless services. The main goal of this thesis is to study two important issues in wireless MIMO communication systems: receiver design for coded MIMO systems, and diversity-multiplexing tradeoff analysis in general fading channels. In the first part of this thesis, we decompose the receiver design problem into two subproblems: MIMO channel estimation and MIMO detection. For the MIMO channel estimation, we develop an expectation-maximization (EM) based semi-blind channel and noise covariance matrix estimation algorithm for space-time coding systems under spatially correlated noise. By incorporating the proposed channel estimator into the iterative receiver structure, both the channel estimation and the error-control decoding are improved significantly. We also derive the modified Cramer-Rao bounds (MCRB) for the unknown parameters as the channel estimation performance metric, and demonstrate that the proposed channel estimation algorithm can achieve the MCRB after several iterations. For the MIMO detection, we propose a novel lowcomplexity MIMO detection algorithm, which has only cubic order computational complexity, but with near-optimal performance. For a 4×4 turbo-coded system, we show that the proposed detector had the same performance as the maximum a posteriori (MAP) detector for BPSK modulation, and 0.1 dB advantage over the approximated MAP detector (list sphere decoding algorithm) for 16-QAM modulation at BER = 10−4. In the second part of this thesis, we derive the optimal diversity-multiplexing tradeoff for

A 2-D shooting-and-bouncing (SBR) ray-tracing method considering ray reflect, transmission and diffraction is used to analyze antenna spacing effect on capacity complementary cumulative distribution functions(CCDFS) of indoor non-line-of-sight (NLOS) MIMO channel and indoor multiple-input multiple-output (MIMO) channel with line-of-sight (LOS) path. The results show that the capacities of MIMO channel with LOS path are less than NLOS MIMO channel capacities in general. But whether in indoor MIMO channel with LOS path or in NLOS indoor MIMO channel, capacities CCDFS of indoor MIMO systems with antenna spacing of 5/spl times/ can reach the theoretical independent and identically distribution (i.i.d) Rayleigh capacities nearly fully. With the decrease of antenna spacing, the capacities dropped also. And the less antenna spacing, the more difference between indoor NLOS MIMO channel capacities and capacities of MIMO channel with LOS path.

An efficient multiple-input multiple-output (MIMO) detection (MD) algorithm includes novel, low-complexity, near-optimal and robust scheme is proposed in wireless communications when imperfect nois...

Since H. Yao proposed the lattice reduction (LR)-aided detection algorithm for the MIMO detector, one can exploit the diversity gain provided by the LR method to achieve performance comparable to the maximum likelihood (ML) algorithm but with complexity close to the simple linear detection algorithms such as zero forcing (ZF), minimum mean squared error, and successive interference cancellation, etc. In this paper, in order to reduce the processing time of the LR-aided detector, a graphics processing unit (GPU) has been proposed as the main modem processor in such a way that the detections can be performed in parallel using multiple threads in the GPU. A 2X2 multiple input multiple output (MIMO) WiMAX system has been implemented using a GPU to verify that various MIMO detection algorithms such as ZF, ML, and LR-aided methods can be processed in real-time. From the experimental results, we show that GPUs can realize a 2X2 WiMAX MIMO system adopting an LR-aided detector in real-time. We achieve a processing time of 2.75 ms which meets the downlink duration specification of 3 ms. BER performance of experimental tests also indicates that the LR-aided MIMO detector can fully exploit diversity gain as well as ML detector.

This paper considers the design of a practical low-density parity check (LDPC)-coded multiple-input multiple-output (MIMO) system composed of M transmit and N receive antennas operating in a flat-fading environment where channel state information (CSI) is assumed to be unavailable both to the transmitter and the receiver. A soft iterative receiver structure is developed, which consists of three main blocks: a soft MIMO detector and two LDPC component soft decoders. We first propose at the component level several soft-input soft-output MIMO detectors whose performances are much better than the conventional minimal mean square error (MMSE)-based detectors. In particular, one optimal soft MIMO detector and two simplified suboptimal detectors are developed that do not require an explicit channel estimate and offer an effective tradeoff between complexity and performance. In addition, a modified expectation maximization (EM)-based MIMO detector is developed that completely removes positive feedback between input and output extrinsic information and provides much better performance compared with the direct EM-based detector that has strong correlations especially in fast-fading channels. At the structural level, the LDPC-coded MIMO receiver is constructed in an unconventional manner where the soft MIMO detector and LDPC variable node decoder form one super soft-decoding unit, and the LDPC check node decoder forms the other component of the iterative decoding scheme. By exploiting the proposed receiver structure, tractable extrinsic information transfer functions of the component soft decoders are obtained, which further lead to a simple and efficient LDPC code degree profile optimization algorithm with proven global optimality and guaranteed convergence from any initialization. Finally, numerical and simulation results are provided to confirm the advantages of the proposed design approach for the coded MIMO system.

Visible Light Communication (VLC) has emerged as a powerful technique for wireless communication systems. Providing high data rate and increasing capacity are the major problems in VLC. Recent evidence suggests that Multiple Input Multiple Output (MIMO) technique can offers improved data rates and increased link range. This paper describes the design and implementation of visible light communication system in indoor environment exploring the benefits of MIMO. The specific objective of this research was to implement a 4×4 Multiple Input (LEDs) Multiple Output (photodetectors)-VLC communication system, where a 16 white power LEDs in four arrays are setting up at transmitter and four RX modules are setting up at receiver side without the need for additional power or bandwidth as well as analyze a mathematical model for a VLC- 4×4 MIMO with different modes such as the suitable angles to cover the entire room. The research designs practically an electronic circuit for the transmitter and receiver with inexpensive components. The power distribution of different propagation modes is calculated for Single Input Single Output (SISO) and MIMO channels in typical room dimensions. The results in this paper indicate that the power is distributed uniformly for entire room when implemented VLC-MIMO as compared to VLC-SISO. Furthermore, a 4×4 MIMO implementing VLC is compared in term of BER vs. SINR with SISO communication system for both Line of Sight (LOS) and Non Line of Sight (NLOS) propagation modes. Comparing the two results of LOS and NLOS, it can be seen that a 4×4 MIMO implementing VLC for LOS perform better than the same system with NLOS due to decreasing in the received power resulted from the multipath effect.

Multiple-input multiple-output (MIMO) detection algorithms have received considerable research interest in recent years, as a result of the increasing need for high data-rate communications. Detection techniques range from the low-complexity linear detectors to the maximum likelihood detector, which scales exponentially with the number of transmit antennas. In between these two extremes are the tree search (TS) algorithms, such as the popular sphere decoder, which have emerged as attractive choices for implementing MIMO detection, due to their excellent performance-complexity trade-offs. In this paper, we survey some of the state-of-the-art VLSI implementations of TS algorithms and compare their results using various metrics such as the throughput and power consumption. We also present notable contributions that have been made in the last three decades in implementing TS algorithms for MIMO detection, especially with respect to achieving low-complexity, high-throughput designs. Finally, a number of design considerations and trade-offs for implementing MIMO detectors in hardware are presented.

Design and implementation of a highly optimized MIMO (multiple-input multiple-output) detector requires cooptimization of the algorithm with the underlying hardware architecture. Special attention must be paid to application requirements such as throughput, latency, and resource constraints. In this work, we focus on a highly optimized matrix inversion free 4×4 MMSE (minimum mean square error) MIMO detector implementation. The work has resulted in a real-time field-programmable gate array-based implementation (FPGA-) on a Xilinx Virtex-2 6000 using only 9003 logic slices, 66 multipliers, and 24 Block RAMs (less than 33% of the overall resources of this part). The design delivers over 420 Mbps sustained throughput with a small 2.77-microsecond latency. The designed 4×4 linear MMSE MIMO detector is capable of complying with the proposed IEEE 802.11n standard.

A novel training-based channel estimation scheme is presented for an uncoded layered space-time system that operates in a wideband frequency selective fading environment of a time-varying multiple-input multiple-output (MIMO) channel. The method uses a pilot matrix consisting of pilot symbols derived from the Paley-Hadamard matrix to estimate the MIMO channel impulse response. The orthogonality of the pilot matrix resolves both the intersymbol interference and the cochannel interference of the wideband MIMO channel. The Toeplitz-like structure of the Paley-Hadamard matrix is exploited to minimise the length of the pilot sequence, reducing pilot symbol overhead. A decision feedback algorithm is used to track the time-varying MIMO channel. Results are presented which demonstrate the performance of the proposed MIMO channel estimator in a layered space-time system for different mobile velocities and system configurations.

Next-generation wireless communication systems will incorporate millimeter wave (mmWave) as one of the key technologies to increase data rates. These forthcoming mmWave systems will integrate multiple-input multiple-output (MIMO) technology to ensure sufficient link margin and are expected to be deployed in conjunction with sub-6 GHz systems. Configuring a MIMO communication link usually relies on estimating channel state information (CSI), which is difficult to acquire at mmWave frequencies due to the low pre-beamforming signal-to-noise ratio (SNR). In this paper, we propose a novel approach to estimate mmWave MIMO channels by leveraging out-of-band information from a sub-6GHz band. Utilizing this approach, we develop three channel estimation methods and compare these methods with one using only in-band information. We investigate the influence of the <italic xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">K</i>-factor, the SNR and the number of antennas on the performance of the proposed channel estimation methods through simulations. Additionally, we compare these methods in terms of their computational complexity. Finally, we validate the performance of the proposed methods through channel measurements conducted in an outdoor environment. The results demonstrate that the proposed methods outperform in-band mmWave channel estimation in terms of spectral efficiency, particularly in scenarios of low SNR and high K-factor.

A novel stochastic multiple-input multiple-output (MIMO) channel model based on the singular value decomposition of the channel matrix is proposed in this study. Under the framework of the proposed model, each of the right singular vectors can be modelled as the product of a stochastic scalar and a non-random vector, as is each of the left singular vectors. The non-random vectors, defined as the eigenmodes of the transmitter and receiver, respectively, can be easily extracted from the measurements, so are the singular values of the channel matrix. The implications of the proposed model's parameters that provide further insight into the MIMO channel are interpreted and a way of exploiting the parameters is given. To validate the proposed model, MIMO channel measurement is carried out under different indoor environments and the channel capacity is analysed. It is shown that the proposed model provides a better fit to the measurement results than the other popular stochastic channel models. The proposed stochastic MIMO channel model can be used for the MIMO communication system design and evaluation.

Motivated by the study of the optimization of the quality of service for multiple input multiple output (MIMO) technique in a wireless communication system. The capacity of MIMO channel in independent Rayleigh channels grows linearly as the number of antennas. However, some limitations on the MIMO capacity is due to the correlation between individual sub-channels of the matrix channel. In this paper, we investigate the MIMO channel capacity in correlated channels using a new correlation matrix model. After some mathematical recalls we derive the general upper bound on the MIMO channel capacity. We give the analytical results, which measure the effect of correlation on the MIMO capacity for a proposal model. Then, we use the correlation matrix approach to compute the capacity of MIMO with respect to signal-to-noise (snr) and then predict the numbers of antennas. By fixing the snr variable to a specific value, we extract informations on the optimal numbers of MIMO antennas. Finally, we have given the variation of the MIMO capacity in the limiting case of N rarr infin for our proposal model and the exponential correlation matrix model.

This paper describes a broadband multiple input, multiple output (MIMO) channel characterization platform and capacity measurement results in indoor office environment. The MIMO testbed has been designed for broadband MIMO channel sounding, capacity measurements and for characterizing the directional-multipaths of the radio propagation channel. The MIMO channel data have been collected in 5 GHz band inside a modern office environment. Capacity results from these experiments are discussed for different propagation conditions, including non line-of-sight (NLOS) and LOS propagations with various spacings between array elements. Spatial correlations are analyzed from the measured data and a frequency selective MIMO channel model based on the correlation statistics is validated. Post-processing of the measured data with a sequential ESPRIT (Estimation of Signal Parameters via Rotational Invariance Techniques) algorithm is utilized to extract the directions of departures and arrivals of multipath components at the transmitting and receiving arrays, respectively. A method of obtaining broadband MIMO capacity, indirectly, from a single directional measurement of MIMO propagation channel is also proposed and verified from the measurement results.

Multicanonical Monte Carlo (MMC) is an adaptive importance sampling technique which employs a blind adaptation algorithm to converge to the optimal biasing distribution. In this paper, we propose an improved MMC algorithm for fast estimation of outage probabilities in Multiple Input Multiple Output (MIMO) channels. The algorithm uses an improved estimator which can provide smooth estimates with high reliability at very low error probabilities. The proposed estimator uses moving average filtering to smooth the visits histograms at each iteration thereby reducing the stochastic fluctuations between iterations. We compare the proposed estimator with the well known Berg's update and the simulation results show that the new estimator can accurately estimate lower error probabilities with the same number of samples.