A Review of Compressive Sensing Detection for Spatial Modulation in Massive MIMO System

Conventional MIMO (multiple input multiple output) system is required to a number of RF chains as much as a number of antennas. If a number of antennas increased then a number of RF chains increased. Therefore, it is difficult to apply conventional MIMO system to mobile terminals with limited power. In this paper, we propose a TDM (time division multiplexing)-based single RF chain MIMO system. The outcome shows that performance of the proposed system is similar to conventional MIMO system using multiple RF chains when STO is corrected by phase angle estimation and the synchronizing signal of received signal.

The multiple-input multiple-output (MIMO) wireless system can either be massive or conventional “small-scale” ones. It has been verified that the massive MIMO technology has a great potential to improve transmission range, spectral efficiency, and coverage compared to conventional MIMO. For realistic antenna configurations systems, there is an increase in the computational complexity associated with signal detection in massive MIMO systems. Several theoretical iterative techniques have been proposed to balance the computational complexity and performance in massive MIMO systems. However, most of these methods have very slow convergence rate. Therefore, we employ the multiple search direction conjugate gradient (MSD-CG) method in massive MIMO uplink systems to reduce the data detection complexity and enhance the performance. The efficiency of the proposed method has been improved by a projection technique that requires a search direction in each sub-domain rather than forming all search directions conjugate to each other. In this paper, we compare the proposed approach to the approximate and exact methods. Our results indicate that the proposed algorithm with realistic antenna configurations is superior to the existing methods for large-scale MIMO systems.

This paper considers large multiple-input multiple-output (MIMO) communication systems with linear precoding and linear minimum mean-squared error (LMMSE) equalization based on the iterative conjugate gradient (CG) algorithm. Convergence of the CG algorithm is fast when the eigenvalues of the received signal's covariance matrix are clustered, suggesting that mean-squared error and receiver complexity can be managed with judicious precoder design. In order to accelerate convergence of an iterative CG receiver, we incorporate constraints on two measures of eigenvalue clustering into the precoder design. Closed-form solutions to the optimal precoders are derived using majorization theory and convex optimization techniques. We show that if there are constraints on receiver complexity, the proposed precoders can improve performance for large MIMO systems operating over slowly time-varying fading channels.

기존 MIMO 시스템 대비 수십 또는 수백 배 많은 송신 안테나들이 설치되어 있는 주파수 분할(frequency division duplex, FDD) 방식의 거대 다중 안테나(massive multiple-input mulitple-output, Massive MIMO)에선 송신 안테나 별 CSI-RS(channel state information reference signal) 전송을 위해 기존 MIMO 시스템 대비 너무 많은 하향 및 상향링크 자원 요소가 필요하다는 한계를 갖는다. 이러한 단점들을 극복하기 위해 본 논문에선 주파수 분할 방식의 거대 다중 안테나 시스템에서 많은 송신 안테나를 사용하더라도 자원요소(resource element, RE)를 재사용함으로써 송신 안테나 수에 비례하지 않는 제한된 양의 하향링크 자원만을 사용하여 CSI-RS를 효과적으로 전송하는 기술 및 자원격자 구조를 제안하였다. Since FDD massive MIMO (multiple-input multiple-output) system deploys hundreds of transmit antennas at base station (BS) compared to conventional MIMO system, the overhead of transmitting channel state information reference signal (CSI-RS) increases proportionally to the number of transmit-antennas. To overcome these disadvantages, we proposed beamforming based CSI-RS transmission technique for FDD massive MIMO system which transmit CSI-RS by limited amount of downlink resources.

This chapter is attempted to provide a survey of the advanced concepts and related issues involved in Multiple Input Multiple Output (MIMO) systems. MIMO system technology has been considered as a really significant foundation on which to build the next and future generations of wireless networks. The chapter addresses advanced MIMO techniques such as polarization diversity and antenna selection. We gradually provide an overview of the MIMO features from basic to more advanced topics. The first sections of this chapter start by introducing the key aspects of theMIMO theory. TheMIMO systemmodel is first presented in a genericway. Then, we proceed to describe diversity schemes used in MIMO systems. MIMO technology could exploit several diversity techniques beyond the spatial diversity. These techniques essentially cover frequency diversity, time diversity and polarization diversity. We further provide the reader with a geometrically based models for MIMO systems. The virtue of this channel modeling is to adopt realisticmethods for modeling the spatio-temporal channel statistics from a physical wave-propagation viewpoint. Two classes for MIMO channel modeling will be described. These models involve the Geometry-based Stochastic ChannelModels (GSCM) and the Stochastic channel models. Besides the listedMIMO channel models already described, we derive and discuss capacity formulas for transmission over MIMO systems. The achieved MIMO capacities highlight the potential of spatial diversity for improving the spectral efficiency of MIMO channels. When Channel State Information (CSI) is available at both ends of the transmission link, the MIMO system capacity is optimally derived by using adaptive power allocation based on water-filling technique. The chapter continues by examining the combining techniques for multiple antenna systems. Combining techniques are motivated for MIMO systems since they enable the signal to noise ratio (SNR) maximization at the combiner output. The fundamental combing techniques are the Maximal Ratio Combining (MRC), the Selection Combining (SC) and the Equal Gain Combining(EGC). Once the combining techniques are analyzed, the reader is introduced to the beamforming processing as an optimal strategy for combining. The use of multiple antennas significantly improves the channel spectral efficiency. Nevertheless, this induces higher system complexity of the communication system and the communication system performance is effected due to correlation between antennas that need to be deployed at the same terminal. As such, the antenna selection algorithm for MIMO systems is presented. To elaborate on this point, we introduce Space time coding techniques for MIMO systems and we evaluate by simulation the performance of the communication system. Next, we emphasis on multi polarization techniques for MIMO systems. As a background, we presume that the reader has a thorough understanding of antenna theory. We recall the basic antenna theory and concepts that are used throughout the rest of the chapter. We rigorously introduce the 3D channel model over the Non-Line of Sight (NLOS) propagation channel for MIMO system with polarized antennas. We treat the depolarization phenomena and we study its effect on MIMO system capacity. The last section of the chapter provides a scenario for collaborative sensor nodes performing distributed MIMO system model which is devoted to sensor node localization in Wireless Sensor Networks. The localization algorithm is based on beamforming processing and was tested by simulation. Our chapter provides the reader by simulation examples for almost all the topics that have been treated for MIMO system development and key issues affecting achieved performance.

The fifth generation cellular communication is all about high speed internet access with devices consuming less amount of power. Millimeter wave Multiple Input Multiple Output (MIMO) systems is a promising technology that offers high data rates due to a large bandwidth. These systems are compact with minimal antenna heights which allows us to deploy these systems more widely. The mm-Wave Massive MIMO systems enhances the data rates to a large extent. But due to the increasing number of antennas to support high data rates, the power consumption of the system goes high. In this paper, a limited channel state information (CSI) based precoding technique has been used to optimize the power consumption and to reduce the computational complexity of the system. The use of Hybrid Precoder architecture with sub array of precoding blocks helps in reducing the computational complexity by many folds. The conditional switching between two stages minimizes the number of computations required. The estimation of Angle of arrival (AoA) enables the precoder to steer the beam at the transmitter for higher throughput. The smart antenna selection algorithm optimizes the power consumption of the system. The two – staged precoding algorithm proposed employs all these techniques to optimize the performance of mm-Wave MIMO systems.

In conventional ways of fast responding and high performing model predictive control using Field Programmable Gate Arrays (FPGA), the approaches developed are applicable only to Single Input Single Output System (SISO). Many real time systems are Multiple Input Multiple Output (MIMO) systems and loop interaction is a major concern and has to be reduced in control of MIMO systems. Also, direct digital control with ability to solve the Quadratic Programming (QP) problem online, which can be applied to complex systems with fast response time and/or embedded applications and with limited computational resource for supervisory control approach, is required in many complex industrial MIMO systems. A novel direct digital control of Model predictive controller with FPGA for a MIMO system which considers and reduces loop interaction and which can also be implemented with very less investment is proposed here. The system was modeled from first principles and then simulated in Labview environment for MIMO system. Implementation of the system and response was verified for a stirred tank system. The proposed system has good performance in terms of reduction in loop interaction which is a major concern in implementation of controller for MIMO systems. Also, direct digital control of MIMO system instead of supervisory control was accomplished.

Multiple-Input Multiple-Output (MIMO) systems that realize high-speed data transmission with multiple antennas at both transmitter and receiver are drawing much attention. In line-of sight (LOS) environments, the performance of MIMO systems depends largely on the difference of the phase difference of direct paths from transmit antennas to each receive antenna. When the phase difference of direct paths are close to each other, the spatial division multiplexing (SDM) channels are not orthogonal to each other so signal detection becomes difficult. In this paper, we propose a MIMO system with relative phase difference time-shift modulation (RPDTM) in Rician fading environments. The proposed scheme transmits independent signals from each antenna at each time slot where the relative phase difference between signal constellations used by transmit antennas varies in a pre-determined pattern. This transmission virtually changes the phase difference of direct paths from transmit antennas to each receive antenna without lowering data rate and without knowledge of the channels. In addition, forward error correction coding (ECC) is applied to exploit the time slots where the receiver can detect the signals easily to improve the detection performance. If there are time slots where the receiver can separate the received signal, the receiver can decode the data by using the time slots and the correlation between data. From the results of computer simulation, we show that MIMO system with RPDTM can achieve the better bit error rate (BER) than the conventional MIMO system. We also show that the MIMO system with RPDTM is effective by about Rician factor K=10dB.

Multiple input multiple output (MIMO) technology has evolved over the past few years into a technology with great potential to drive the direction of future wireless communications. MIMO technology has become a solid reality when massive MIMO systems (MIMO with large number of antennas and transceivers) were commercially deployed in several countries across the world in the recent past. Moreover, MIMO has been integrated into state-of-the-art paradigms such as fifth-generation (5G) networks as one of the main enabling technologies. MIMO possesses many attractive and highly desirable properties such as spatial multiplexing, diversity gains, and adaptive beamforming gains that leads to high data rates, enhanced reliability, and other enhancements. Nevertheless, beyond 5G technologies demand wireless communication systems with, among other properties, immensely higher data rates and better reliability simultaneously at the same time. In this work, a new, novel MIMO technique for simultaneously achieving multiplexing and diversity gains as well as completely eliminating any processing at the MIMO receiver, leading to advantages such as low complexity and low power consumption, is proposed. The proposed technique employs the design of interference-canceling matrices, which are calculated from the channels between the transceiver antennas, where the matrices are employed at the base station to help achieve multiplexing and diversity gains simultaneously. The novelty and efficiency of the introduced paradigm is demonstrated via mathematical models and validated by Monte Carlo simulations. Results indicate that the proposed system outperforms conventional MIMO models.

Large‐scale multiple‐input multiple‐output (MIMO) system is considered one of promising technologies to realise next‐generation wireless communication system (5G). So far, channel estimation problem is a big obstacle to develop large‐scale MIMO system design due to high computational complexity and curse of dimensionality, which are caused by the long delay spread as well as a large number of antennas. Hence, devising any low‐complexity channel estimation method could promote the successful development of the large‐scale MIMO system. Due to the fact that, large‐scale MIMO channels often exhibit sparse or/and cluster‐sparse structure, in this study, the authors propose an effective low‐complexity large‐scale MIMO channel estimation method by using affine combination of sparse adaptive filtering filters. First, problem formulation and standard affine combination of adaptive least mean square (LMS) filters are introduced. Then they propose an effective affine combination method with two sparse LMS filters and design an approximate optimum affine combiner according to stochastic gradient search method. Later, to verify the proposed algorithm for large‐scale MIMO channel estimation, both theoretical analysis and numerical simulations are provided to confirm effectiveness of the proposed algorithm which can achieve better estimation performance than the traditional methods.

Accurate channel state information (CSI) at base station (BS) is the key to achieve full multiplexing and diversity gain in traditional multiple-input multiple-output (MIMO) systems. In frequency-division-duplex (FDD) systems, it is obtained through downlink training and uplink feedback. However, the training and feedback overhead in massive MIMO systems is unacceptable for the large number of antennas equipped at BS. To reduce the CSI feedback overhead and improve CSI quantization accuracy, we propose a limited feedback scheme for spatio-temporal correlated massive MIMO channel. The proposed scheme jointly performs Karhunen-Loève transform (KLT) and polar-cap quantization on CSI. For the compactly deployed antennas at BS, there exists spatial correlation in massive MIMO channel. When the user equipment (UE) moves slowly, adjacent channels feature temporal correlation. The high dimensional and spatial correlated CSI is compressed through KLT. Then the compressed CSI is normalized to be isotropic to perform polar-cap quantization. Simulation results show that the proposed scheme is capable of improving the sum-rate performance with limited feedback bits for massive MIMO systems.

A High-rate spatial modulation (HR-SM) transmission scheme was proposed in [1]. Compared to conventional Multiple-Input Multiple-Output (MIMO) systems, HR-SM has better bit-error-rate (BER) performance with trade off of spectral efficiency. In this paper, we propose a hardware architecture of HR-SM detector for 4×4 system using Modified-Minimum Mean Square Error — sorted QR decomposition (MSQRD) algorithm which was proposed in [2]. Implementation result shows that our design achieves higher throughput compared to other implementations in conventional MIMO systems despite the disadvantage of spectral utilization in HR-SM, while still keeps latency low and hardware usage acceptable.

Consider a multiple input multiple output (MIMO) system with pulse amplitude modulation (PAM), where each transmit antenna is allowed to choose a different transmission delay. (We refer to this system as a MIMO system with asynchronous PAM.) Such MIMO systems have been studied before for increasing diversity and avoiding unintentional beamforming. We quantify the capacity/outage capacity improvement due to asynchronism and the corresponding spectral leakage (if any) for MIMO point-to-point and MIMO broadcast channels. We show that under commonly used transmitter spectral mask constraints, the channel has unbounded degrees of freedom. Synchronous PAM exploits only a finite number of these degrees of freedom, and asynchronism helps to improve capacity. For most cases of interest, two distinct shifts attain most of the capacity improvement. These gains are robust to interference from adjacent carriers. Analysis of the spectrum of the asynchronous PAM suggests that optimal water-filling based schemes are useful for improving capacity only in directional links due to possible spectral leakage, while uniform power allocation leads to capacity improvement without any extra spectral leakage.

The scaling up of antennae and terminals in large-scale multiple-input multiple-output (MIMO) systems helps increase the spectral efficiency at the penalty of prohibitive computational complexity. In conventional linear detection such as the minimum mean square error (MMSE) signal detection, the high complexity is mainly caused by solving the inversion of random matrix, especially in large-scale MIMO systems. In order to reduce the complexity of the matrix inversion, we proposed a low-complexity MMSE detection scheme based on symmetric successive over relaxation (SSOR) method, referred to as MSSD method. The proposed method exploits the channel hardening phenomenon, which means the off-diagonal terms of the HHH matrix become increasingly weaker compared to the diagonal terms as the size of the channel gain matrix H increases. In addition, we point out that the channel estimation scheme used in channel hardening-exploiting message passing receiver (CHEMP) is very suitable for the MSSD algorithm. For the considered large MIMO settings, simulation results show that the performance of the MSSD algorithm is very close to the classical MMSE detection algorithm with a small number of iterations.

Multiple Input Multiple Output (MIMO) systems with limited Radio Frequency (RF) chains play a pivotal role in the Fifth Generation (5G) of wireless networks. However, the transmitter of Generalized Spatial Modulation MIMO (GSM-MIMO) systems that characterized by a single RF chain and multiple active antennas is capable of reducing both the energy consumption and the transmitter cost. In this paper, combining GSM-MIMO systems with the fully digital Geometric Mean Decomposition (GMD)-based precoding scheme and Analog Beamforming (ABF) into Hybrid Beamforming (HBF) regime is presented for Millimeter-wave (mmWave) massive MIMO systems which is a key enabler for 5G networks. In addition, applying the norm-based user selection algorithm in GSM-MIMO scheme with GMD-based hybrid precoding is proposed, and referred to as Multiuser Steered GSM-MIMO (MUS-GSM-MIMO) scheme. Simulation results demonstrate that the proposed schemes are capable of achieving considerable performance gains over the conventional GSM-MIMO schemes, while avoiding the overwhelming costs of multiple RF chains. Therefore, the proposed schemes are very efficient and highly suitable for large-scale and 5G wireless networks.