A Robust Method of Vehicle Stability Accurate Measurement Using GPS and INS

Integration of Global Positioning System (GPS) and Inertial Navigation System (INS) are very practical method to get high precision navigation. GPS/INS data Fusion in navigation has been a research topic for decades. Usually the update time of GPS an INS is different. The update time of GPS is 20HZ, and the time of INS is 100HZ or higher. Since GPS and INS are mainly methods in navigation system. Techniques of fusing GPS and INS data are in high demand in navigation industry. Usually the Karman filter is used to fuse the data from GPS and INS. But the Kalman filter is model-dependent and a priori the model parameters need to be known. In this work, a generic and intelligent approach of GPS and INS data fuse using fuzzy interpolation before Kalman algorithm is proposed. First a simplified interpolation model is introduced in a ordinary GPS and INS data fusion. Second a fuzzy rule-based system is established to fuzzy interpolation with objective fuzzy method. Then the parameters of objective fuzzy system are identified, the best n-rule is determinate and the optimal rule base system is found. Finally this approach is applied on an example for a car GPS and INS data fusion, and the results are calculated with computer system to demonstrate the advantages of this approach.

In the integration of Global Positioning System (GPS) and Inertial Navigation System (INS), the commonly used Kalman filter provides satisfactory results if both sources of information are continuously available. However, GPS outages provoke a fast degradation of precision, especially in low dynamic trajectories such as a mobile platform device held by a human operator. To deal with this problem we propose a data-filtering scheme to apply to INS raw data prior to the integration with GPS. The proposed technique proves to be very valuable for mitigating the high short-term instability of raw INS data during the walking movement and is also capable of eliminating the induced undesirable human operator vibrations. Final imposed corrections adapted to the particular dynamical response of the INS sensor provide comparably accurate results and often better than those achieved in similar works with the use of the Kalman filter.

In present days, real time navigation depends on Kalman filter to fuse data from Global Positioning System (GPS) and Inertial Navigation System (INS). But there exist drawbacks like long design time, requirement of prior knowledge in fusing data from GPS and INS using Kalman Filter. In order to overcome the drawbacks of Kalman filter, GPS and INS integration are done using Artificial Neural Networks (ANN) like FFNNs. But still there exists certain drawbacks like less accuracy in FFNNs for GPS and INS data integration. Therefore, this paper introduces Higher Order Neural Networks (HONNs) approach for INS and GPS data integration to overcome the drawback. A higher order feed forward neural network architecture with optimum number of nodes is used. In the given architectures, the replacement of summation at each node by multiplication results in more powerful mapping, because of its capability of processing higher-order information from training data. Performance comparison of HONNs with FFNNs shows that the proposed architecture provides satisfactory results in terms of error rate and number of epochs. The HONNs like Multiplicative Neural Network (MNN) module and Sigma-Pi-ANN module and Traditional Feed Forward Neural Networks(FFNNs) like Radial Basis Function Neural Network (RBF) module and Back propagation Neural Network (BPN) module are trained to predict the INS position error and provide accurate position of the moving aircrafts. Sigma-Pi ANN is found to be the best in terms of accuracy, number of epochs and execution time among the two HONNs.

Global Positioning System and Inertial Navigation System can be used to determine position and velocity. A Global Positioning System module is able to accurately determine position without sensor drift, but its usage is limited in heavily urbanized environments and heavy vegetation. While high-cost tactical-grade Inertial Navigation System can determine position accurately, low-cost micro-electro-mechanical system Inertial Navigation System sensors are plagued by significant errors. Global Positioning System is coupled with Inertial Navigation System to correct the errors, while Inertial Navigation System itself can be used to provide navigation solution during a Global Positioning System outage. Data from Global Positioning System and Inertial Navigation System can be integrated by extensive Kalman filtering, using loosely coupled integration architecture to provide navigation solutions. In this study, real-time low-cost loosely coupled micro-electro-mechanical system Inertial Navigation System/Global Positioning System sensors have been used for pedestrian navigation. Trial runs of Global Positioning System outages have been conducted to determine the accuracy of the system described. The micro-electro-mechanical system Inertial Navigation System/Global Positioning System can successfully project a trajectory during a Global Positioning System outage and produces a root mean square error of 9.35 m in latitude direction and 10.8 m in longitude direction. This technology is very suitable for visually impaired pedestrians.

How to achieve continuous, reliable and accurate positioning performance using low-cost sensors is one of the main challenges for aviation navigation system. Global Positioning System (GPS) can provide the primary means of navigation in a number of aviation navigation applications (e.g., manned and unmanned aircraft vehicle, airport ground vehicle). However, GPS signal deteriorations typically occur due to aircraft itself during maneuvering, ionospheric scintillation, Doppler shift, multipath and so on. Thus, there is a need to research GPS augmentation strategies which can be used in the Communication, Navigation, Surveillance/Air Traffic Management. GPS integration with Inertial Navigation system (INS) is one of the key strategies. But once GPS signal outages, the integrated navigation system works in pure INS, and positioning accuracy deteriorates with time. When using low cost GPS/INS integration, a primary problem is the rapid performance deteriorate during GPS outages. To provide continuous, accurate and reliable positioning information in aviation, discrete grey prediction model (DGPM) aided fusion methodology is proposed. The DGPM provides pseudo-GPS position information for INS during GPS outages. The mathematical model of integrated navigation system is established, including INS error equations, Kalman filter and DGPM. The model works in the update mode when there is no GPS failure, whereas it switches to the prediction mode in case of GPS outages. To verify the feasibility and effectiveness of the proposed methodology, real road test is performed. The comparison results show that accuracy of longitude and latitude are improved by more than 80% and 70%, respectively. The DGPM can effectively provide position corrections for standalone INS during GPS outages.

With the development of the intelligent vehicle navigation systems and vehicle networking systems, vehicle positioning and state estimation become very important. This paper investigates the integration of Global Positioning System (GPS), Inertial Navigation System (INS) and Dead Reckoning based on Anti-lock Braking System (ABSDR) positioning based on Kalman filter, and aims at achieving full-time vehicle positioning. In this paper, we use Kalman Filter to estimate INS positioning error based on GPS or ABSDR solution, take the INS solution compensated with estimated error as system output. This paper introduces INS positioning algorithm, dead reckoning method based on the ABS wheel speed and Kalman filtering method. After that, simulation analysis and experimental verification of the positioning algorithm are carried out. The results show that the system output high-precision high-frequency positioning information when GPS is available, and when GPS is unavailable, INS positioning errors can be compensated well with ABSDR introduced, achieving the full-time positioning of the vehicle.

A smart city’s main purpose is to provide intelligent responses to different problems of the rapid urban population growth. For instance, integrating fleet management solutions into intelligent transportation systems (ITS) can efficiently resolve transportation problems relying on each vehicle information. Usually, the position estimate is ensured by the integration of the Global Positioning System (GPS) and Inertial Navigation Systems (INS). For multisensor data fusion, the Extended Kalman Filter (EKF) is generally applied using the sensor’s measures and the GPS position as a helper. However, the INS are expensive and require more complex computing which induces restrictions on their implementation. Furthermore, the EKF performance depends on the vehicle dynamic variations and may quickly diverge because of environmental changes. In this paper, we present a robust low cost approach using EKF and Support Vector Machines (SVM) to reliably estimate the vehicle position by limiting the EKF drawbacks. The sensors used are a GPS augmented by a low cost wireless sensor network. When GPS signals are available, we train SVM on different dynamics and outage times to learn the position errors so we can correct the future EKF predictions during GPS signal outages. We obtain empirically an improvement of up to 94% over the simple EKF predictions in case of GPS failures.

In modern navigation applications, Inertial Navigation System (INS) is attractive for integrating with Global Positioning System (GPS). Although traditional GPS/INS integrated systems can bridge the GPS gaps, the navigation capability is strongly dependent on the performances of standalone INS. As an important complementary, a new terrestrial, Radio-Frequency (RF) based, distance measurement technology “Locata” can provide continuously time-synchronised ranging signals even in many GPS challenged environments e.g. poor satellite geometry, signal blockage in suburban, tunnels, high rise buildings canyon. This paper investigates the integration of Locata, GPS, and INS with a focus on the loosely-coupled triple integration algorithm. Firstly, the Conventional Kalman Filtering (CKF) based triple integration of Locata/GPS/INS architecture is described and briefly discussed. Secondly, to overcome the pitfalls of conventional Locata/GPS/INS integration algorithm, an Adaptive Dual Kalman Filtering (ADKF) algorithm is proposed and developed in three stages: (1) To enhance the reliability of position and velocity (PV) quantities generated from Locata/GPS integrated sensors, the 1st KF is additionally constructed to reliably estimate the PV solution before fusing INS sensor. (2) Combining the 15-state INS error model and the measurements which are the differences between PV solution from the 1st KF and INS sensor, the 2nd KF is subsequently employed to correct the INS navigation errors. (3) The final integration solution is reversely used as the feedback for precisely estimating the stochastic model (i.e. variance of dynamic and observation model noise) of the 1st KF. Finally, the real flight experiment is carried out to demonstrate the efficiency and validity of Locata/GPS/INS integration algorithms. The results show that: (1) Conventional GPS/INS integration performs well but its accuracy dramatically decreases when GPS signals are unavailable for a short period. (2) Augmented by Locata, GPS/INS produces tolerable results in whole experiment even without aiding of GPS. (3) By additionally operation of the 1st KF and adaptively estimating its stochastic model with feedback of integration solution, ADKF achieves more accurate and reliable position, velocity and attitude (PVA) solution than CKF.KeywordsINS errorLocata/GPS/INS integrationAdaptive Kalman filteringStochastic model

Global Positioning System (GPS) and Inertial Navigation System (INS) data can be integrated to provide a reliable navigation. This paper presents an approach of solving GPS/INS data integration problem, without the need of modeling the characteristics of GPS and INS sensors. Use of Artificial Intelligence (AI) techniques for an intelligent navigation system has been developed as an alternative to the conventional Kalman filter approach, in which it is mandatory to model the entire system. Many AI techniques have been implemented for the same, in which the use of ANFIS instead of neural networks and fuzzy logic has been widely implemented. In this paper Memetic optimization on ANFIS (MANFIS) has been proposed which outperforms Genetically optimized ANFIS (GANFIS).

The extended Kalman filter (EKF) as a primary integration scheme has been applied in the Global Positioning System (GPS) and inertial navigation system (INS) integrated system. Nevertheless, the inherent drawbacks of EKF contain not only instability caused by linearization, but also massive calculation of Jacobian matrix. To cope with this problem, the adaptive interacting multiple model (AIMM) filter method is proposed to enhance navigation performance. The soft-switching characteristic, which is provided by interacting multiple model algorithm, permits process noise to be converted between upper and lower limits, and the measurement covariance is regulated by Sage adaptive filtering on-line Moreover, since the pseudo-range and Doppler observations need to be updated, an updating policy for classified measurement is considered. Finally, the performance of the GPS/INS integration method on the basis of AIMM is evaluated by a real ship, and comparison results demonstrate that AIMM could achieve a more position accuracy.

This paper demonstrates the use of Global Positioning System (GPS) and Inertial Navigation System (INS) in order to develop an Unmanned Ground Vehicle (UGV) devised to perform a wide variety of outdoor tasks. There are many applications for autonomous UGVs such as tactical and surveillance applications, exploration of areas inaccessible by humans. Capable to navigate to a specific location, and control their motion depending on their surroundings without human intervention. The inertial navigation system makes use of Inertial Measurement Units (IMUs) to measure the change to the UGV's positional parameters, orientation and speed which are continuously monitored and updated. With the advent of GPS, and the positional data from the inertial system the positional information is computed leading to a more accurate control of the UGV; which otherwise suffers from integration drift that occurs with the implementation of inertial systems alone. Autonomous control of the UGV is implemented by coupling GPS sensor and Mission Planner, a tool to map waypoints from Google Maps. Furthermore, system stability and ideal PID (Proportional, Integral and Derivative) values are determined using bicycle modeling analysis to achieve better estimates and control of the UGV. DOI: http://dx.doi.org/10.11591/ijece.v4i3.5183

This paper considers estimation problems where inequality constraints are imposed on the outputs of linear systems and can be modeled by nonlinear functions. In this case, censoring functions can be designed to constrain measurements for use by filters and smoothers. It is established that the filter and smoother output estimates are unbiased, provided that the underlying probability density functions are even and the censoring functions are odd. The Bounded Real Lemma is employed to ensure that the output estimates satisfy a performance criterion. A global positioning system (GPS) and inertial navigation system (INS) integration application is discussed in which a developed solution exhibits improved performance during GPS outages when a priori information is used to constrain the altitude and velocity measurements.

Misalignment can be an important error source in the integration of the global positioning system (GPS) and inertial navigation systems. This paper presents car test results on the estimation of alignment errors in the integration of a low-grade inertial measurement unit (IMU) with accurate GPS measurement systems. The car test was conducted with a low-cost solid-state IMU and carrier-phase differential GPS measurement systems. Test results showed that changes in the angular velocity improve the estimation of the lever arm between the GPS antenna and IMU. They also showed that changes in acceleration improve the estimation of the relative attitude between the GPS antenna array and IMU. The lever arm was estimated with a 10-cm error. The relative attitude was estimated with a half-degree error. An iterative scheme was used to improve the estimation of the alignment errors during postprocessing. The scheme was shown to be useful when the test car could not have sufficient changes in motion due to limitations in its path. With the given set of test data, the estimation error decreased as the number of iterations increased.

For the guidance, control and navigation of autonomous vehicles, both positioning and orientation are important for mission success and surveillance. Global positioning system (GPS) and strapdown inertial navigation system (SINS) have complementary characteristics to overcome the demerits of each other and can well perform as integrated navigation system. The observability analysis of low-cost SINS/GPS from many researches shown that the heading and yaw rate gyro bias is unobservable in straight motion and with constant acceleration. This paper presents integration of low-cost SINS/GPS aided with odometer and heading from two antennae GPS receiver to overcome this problem and to control the accuracy degradation during GPS outage. The carrier phase measurements are processed to obtain the heading from two antennae position measurement. The obtained heading and position from GPS and velocity measurement from odometer are used as observation input to extended Kalman filter (EKF) for the heading and positioning accuracy improvement of SINS/odometer/GPS integrated system for land vehicle navigation. When GPS signal is unavailable, the filter switches to SINS/odometer integration to control the position and velocity errors growth during this period. The observation model for heading measurement from two antennae is derived for the designed system. A field test was conducted to check the effectiveness using proposed method for heading and positioning accuracy improvement. The test results showed that Low-cost IMU/Odometer/ Two Antennae GPS integrated systems' accuracy both in position and heading is improved significantly.

State estimation techniques are important tools for analyzing systems that contain states that are not directly measureable. If the estimated states are used, for example, in place of the true states in a feedback controller, the accuracy and stability of the estimates becomes crucial for the safe and effective execution of the controller. This is especially important in aircraft control applications, where safety is an essential concern. Because of this, the stability characteristics of the state estimation are investigated. Additionally, two different nonlinear Kalman filters are considered and compared with respect to various design parameters. This work considers the sensitivity and stability characteristics of nonlinear state estimation through the aircraft attitude estimation problem. This problem is approached using sensor information from Global Positioning System (GPS) and Inertial Navigation System (INS) in order to obtain estimates of the aircraft attitude angles. This case study uses experimentally collected flight data from subscale aircraft to derive estimation results. The goal of this work is to obtain a better understanding of the properties of nonlinear Kalman filters in order to make more informed decisions regarding the selection and tuning of these filters for different real-world applications.