- Research Article
43
- 10.1006/jaer.1997.0251
Triaxial Testing of Unsaturated Agricultural Soils
- Apr 01, 1998
- Journal of Agricultural Engineering Research
- Dvoralai Wulfsohn + 2 more +2
Triaxial Testing of Unsaturated Agricultural Soils
A state-dependent elasto-plastic constitutive model for both saturated and unsaturated soils is presented in this paper. The model, which is developed under an extended critical-state framework, uses two independent stress state variables: net normal stress and matric suction. In addition, the influence of a simplified non-linear soil-water characteristic curve on mechanical behaviour is incorporated in the model by using a bi-linear function. Most importantly, a state-dependent dilatancy formulation is introduced to account for the effects of stress level or stress ratio, internal state (density) and soil suction. In this paper, details of the model formulation and the determination of model parameters are described and reported. By using the new model, numerical simulations of triaxial tests have been carried out on both saturated and unsaturated fine-grained (sandy silt) and coarse-grained (gravelly sand) weathered soils. The simulated triaxial tests include undrained shear tests on saturated specimens, constant water content tests and wetting tests under constant deviator stress on unsaturated specimens. The computed results show that the stress–strain and volumetric-shear–strain relationships at both loose and dense and saturated and unsaturated states can be modelled properly with a single set of parameters. Moreover, the model is capable of capturing some key observed features, such as a sudden increase in shear strain and volumetric strain as suction is reduced under a constant deviator stress.
Triaxial Testing of Unsaturated Agricultural Soils
Triaxial Testing of Unsaturated Agricultural Soils
Limit Analysis of Basal Heave Stability in Unsaturated Soils Based on the Unified Strength Theory
An evaluation method was presented on the basal heave stability in unsaturated soils. A basal heave failure mechanism was established wherein the admissible velocity field was constructed in the light of the Prandtl failure mode. The shear strength theory based on two independent stress state variables was employed for unsaturated soils. The unified strength theory was introduced to account for the influence of intermediate principal stress. Analytical solution of safety factor (Fs) was then deduced based on the upper bound theory of limit analysis, and relevant numerical solutions were solved by means of the strength reduction method. It is found from parametric analysis that the intermediate principal stress and matric suction have a significant impact on Fs. Specifically, Fs is seriously underestimated if they are ignored. The theoretical framework in this work provides a new idea for analyzing the basal heave stability of unsaturated soils.
Read morePressuremeter testing in a calibration chamber with unsaturated minco silt
The pressuremeter is an excellent test to determine the in situ stress-strain relationship for soil. Many of the theories and methods of analysis for the pressuremeter have been developed using saturated soil or dry soil mechanics. Unsaturated soil is frequently encountered during subsurface exploration, especially in arid regions of the world where the ground water table can be at substantial depth. Thus, there is a need for methods to interpret pressuremeter test data from unsaturated soil. At the University of Oklahoma, multiple pressuremeter tests have been conducted in unsaturated soil in a laboratory controlled environment via the use of a calibration chamber. The soil beds were built of a clayey silt to encompass a range of matric suction from 15 kPa to 90 kPa. In addition to the influence of matric suction, the influence of net normal stress on pressuremeter test results was also investigated. Thus, the soil beds were compressed at three different net normal stresses. Multiple approaches were taken to control and measure the matric suction in the soil beds. The active approach involved regulating the pore air and pore water pressure of the soil beds via a pressure control system and high air-entry porous discs. The passive approach involved compacting the soil beds at moisture contents with reference to a target matric suction based on the soil-water characteristic curves and taking measurements of the pore water pressure in the soil beds via tensiometers. Cavity expansion theory was incorporated in the analyses of the experimental results. This paper presents the results of the pressuremeter tests in unsaturated Minco Silt beds conducted in the calibration chamber at different levels of matric suction, and discusses the influence of various testing parameters on the results.
Read moreWetting-induced softening behavior of an unsaturated expansive clay
Studying the wetting-induced softening behavior of unsaturated soils is important for understanding rain-induced slope failures in unsaturated soils. However, experimental studies on expansive soils are limited. This study investigates the wetting-induced softening characteristics of an unsaturated expansive clay via suction-controlled triaxial tests on recompacted and natural specimens. It was found that the wetting-induced swelling of the soil included a significant component of plastic strain and its magnitude decreased with the net confining stress. When a soil specimen was subjected to wetting at a constant deviator stress, a threshold value of soil suction was identified after which the axial strain increased greatly. This value tended to increase with the applied net stress ratio. After the threshold suction, the wetting process for recompacted specimens could be divided into a yielding process associated with volumetric strain hardening/softening and a failure process in which the volumetric behavior depended on the applied net stress ratio. The natural specimens exhibited a brittle failure like a heavily overconsolidated soil during wetting at a constant deviator stress and continuous volumetric dilation occurred after the threshold suction. The wetting-induced softening soil behavior revealed from the present study could interpret the rain-induced progressive slope failure in unsaturated expansive soils.
Read moreGeneralized plasticity state parameter‐based model for saturated and unsaturated soils. Part II: Unsaturated soil modeling
The aim of this paper is to extend the generalized plasticity state parameter‐based model presented in part 1 to reproduce the hydro‐mechanical behavior of unsaturated soils. The proposed model is based on two pairs of stress–strain variables and a suitable hardening law taking into account the bonding—debonding effect of suction and degree of saturation. A generalized state parameter for unsaturated state is proposed to reproduce soil behavior using a single set of material parameters. Generalized plasticity gives a suitable framework to reproduce not only monotonic stress path but also cyclic behavior. The hydraulic hysteresis during a drying—wetting cycle and the void ratio effect on the hydraulic behavior is introduced. Comparison between model simulations and a series of experimental data available, both cohesive and granular, are given to illustrate the accuracy of the enhanced generalized plasticity equation. Copyright © 2010 John Wiley & Sons, Ltd.
Read moreBehavior of a Loosely Compacted Unsaturated Volcanic Soil
In this paper, the stress-strain relationship and volumetric behavior of a loosely compacted unsaturated decomposed volcanic soil (fill) were studied by conducting three series of triaxial stress path tests: (1) consolidated undrained on the saturated fill; (2) constant water content; and (3) a reducing suction under constant deviator stress on the unsaturated fill. The last two series of tests were designed to simulate the effects of undrained response and rainfall infiltration in initially unsaturated slopes, respectively. It was found that the saturated loose volcanic soil behaves like clay under isotropic compression but it resembles sand behavior when it was subjected to undrained shear. For isotropically consolidated unsaturated specimens sheared under a constant water content, a hardening stress-strain and a nonlinear shear strength-suction relationship are observed. At relatively high suctions, both angle of friction and apparent cohesion appear to be independent of suction. Volumetric contraction during shear is observed in this series of tests. On the other hand, anisotropically consolidated loose unsaturated specimens subjected to a reducing suction change from contractive to dilative behavior as the net mean stress increases. This observed volumetric behavior, unlike the shear strength, is stress path-dependent and cannot be explained by using the existing elastoplastic critical state theoretical framework extended for unsaturated soils.
Read moreIs Matric Suction a Stress Variable?
The writer attempts to clarify and address two fundamental questions regarding the appropriate use of matric suction in unsaturated soil mechanics: Is matric suction a stress variable? and Is matric suction a stress state variable? These questions are examined by employing the universally accepted mechanical equilibrium principle, the concept of representative elementary volume (REV) for air-water-solid multiphase porous media, and physical and logical reasoning. It is clarified that matric suction is not a stress variable at a typical air-water-solid REV level, and it can be considered as a stress state variable. However, when it is considered as a stress state variable, there is an interdependency or coupling between matric suction and the net normal stress if both of them are concurrently used to describe the state of stress in unsaturated soils. It is illustrated that the answers to these questions bear important implications for the conceptualization, theorization, and application of unsaturated soil mechanics.
Read moreSwell pressure, matric suction, and matric suction equivalent for undisturbed expansive clays
Methods of computation for soil heave based on an “equivalent” net normal stress path approach often have built-in assumptions regarding the relationship between in situ matric suction, overburden stress, and swell pressure. The term “matric suction equivalent” has been previously defined as the difference between in situ state of stress projected on the net normal stress plane (represented by swell pressure) and overburden stress. Correlations between matric suction, overburden stress, and swell pressure for matric suction values in excess of the air-entry value have not been well studied and are explored here for expansive soils. Filter paper (in-contact) and constant volume swell pressure tests were performed on undisturbed tube samples of expansive soils taken from Arizona, Colorado, and Texas. In general, the ratio of the matric suction equivalent to the matric suction decreases with increasing soil suction. An empirical relationship was established in which the matric suction equivalent was found to be proportional to the logarithm of the matric suction for in situ matric suctions greater than a certain value, termed as the “intercept matric suction”. A correlation between the intercept matric suction and the soil’s plasticity index (PI) was found for the clays of this study. The developed correlations represent a method for obtaining approximate estimates of in situ matric suction for expansive soils from PI and swell pressure data. Implications of the study findings for the use of an equivalent net normal stress approach for estimation of soil heave are explored.
Read moreSwelling and Collapse of Unsaturated Soils Due to Inundation Under One-Dimensional Loading
Volume change of unsaturated soils is controlled by two stress state variables which are net normal stress and matric suction. Volume change phenomenon due to a change in matric suction or water content can be either shrinkage, swelling or collapse, and depends on the level of net normal stress and the initial void ratio of the soil. In this paper, consolidated kaolin specimens were air dried to various water contents and then inundated with water under different net normal stresses in order to study the wetting-induced volume change. The oedometer apparatus was used to carry out the swell test while the constant-rate-of-strain apparatus was used to carry out the constant volume test. The objective of this paper is to investigate the transition of swelling and collapse phenomenon due to different net normal stresses and to derive a method to estimate the wetting induced volume and net normal stress change of unsaturated soil. Based on the tests results, the pre-consolidation void ratio for the same soil before and after inundation is the same, the slope of the normal and unsaturated compression lines are the same under constant degree of saturation conditions and slopes of the unloading line under saturated and unsaturated condition are different. Based on the test results, a method to determine the wetting-induced swelling and collapse of unsaturated soils was proposed. The proposed method was verified using data from the literature.
Read moreA thermo‐hydro‐mechanical model for unsaturated soils based on the effective stress concept
A simple thermo‐hydro‐mechanical (THM) constitutive model for unsaturated soils is described. The effective stress concept is extended to unsaturated soils with the introduction of a capillary stress. This capillary stress is based on a microstructural model and calculated from attraction forces due to water menisci. The effect of desaturation and the thermal softening phenomenon are modelled with a minimal number of material parameters and based on existing models. THM process is qualitatively and quantitatively modelled by using experimental data and previous work to show the application of the model, including a drying path under mechanical stress with transition between saturated and unsaturated states, a heating path under constant suction and a deviatoric path with imposed suction and temperature. The results show that the present model can simulate the THM behaviour in unsaturated soils in a satisfactory way. Copyright © 2010 John Wiley & Sons, Ltd.
Read moreUnsaturated Soil Mechanics Principles to Remove and Replace Mitigation for Expansive Clays
The efficacy of removal and replacement as a mitigation alternative for expansive soil is discussed in view of numerical unsaturated flow/deformation results. Observations with respect to selection of depth and replacement soil type (similar, more, or less permeable than underlying expansive clay) are presented in the context of unsaturated flow and stress/deformation principles. Comparisons are made between various remove and replace options on the basis of extent and degree of wetting (changes in soil suction) and on ground surface total and differential movements. Selection of optimal removal and replacement depth and replacement material type requires consideration of unsaturated flow principles and understanding of the role of both net normal stress and matric suction in unsaturated soil response. Complexities in the unsaturated flow process which impact the efficacy of the remove and replace method are primarily because of the highly nonlinear nature of the unsaturated soil storage function (SWCC) and hydraulic conductivity function. Further, because the unsaturated hydraulic conductivity of soils depends on the value of soil suction, placement water content of the replacement layer has significant effect on performance. The net result is that the impact of various remove and replace options is not always intuitive. The findings presented, although not encompassing of all possible removal and replacement configurations or surface flux conditions, set the stage for application of remove and replace mitigation methods based on fundamental unsaturated soil mechanics principles.
Read moreModelling of shear stiffness of unsaturated fine grained soils at very small strains
Modelling of shear stiffness of unsaturated fine grained soils at very small strains
Modelling shear strength of compacted soils
Compacted soils constitute most engineering projects such as earth dams, embankments, pavements, and engineered slopes because of their high shear strength and low compressibility. The shear strength of compacted soils is a key soil parameter in the design of earth structures but it is seldom determined correctly due to their unsaturated state. The shear strength of compacted soils can be better evaluated under the framework of unsaturated soil mechanics. Saturated and unsaturated tests were conducted on compacted specimens using conventional direct shear apparatus under constant water content condition. Tests were conducted at different water contents and net normal stresses. The main objective of this study is to develop a shear strength model for compacted soils. Initial matric suction was measured before the test using the filter paper method. The two-stress state variables together with the extended Mohr-Coulomb failure criterion for unsaturated soils were used to obtain a lower bound model of the shear strength. The model was demonstrated using published data.
Read moreInstability of Unsaturated Soils Under Constant Deviatoric Stress in Drained Conditions
The paper presents the results of an experimental investigation to study the instability of unsaturated slopes under constant deviatoric stress in drained conditions. The experimental program included compression triaxial tests on specimens prepared with various degree of compactions, i.e., 68%, 76%, and 83% and subjected to net confining stresses of 30, 50 and 90 kPa. During shear process, the specimens were first sheared in constant water content conditions to the pre-defined value of deviatoric stress (i.e., 25% of qmax). The pre-defined deviatoric stress on specimens was then kept constant, and matric suction was decreased by increasing pore water pressure to start water infiltration. After completed water infiltration, the specimens were sheared again in constant water content conditions. The results showed that the behavior of soil is affected significantly by variation in the degree of compaction and confining stress when subjected to water infiltration. Very loose soil with low net confining stress showed large collapse deformation. Finally, it was also observed that the gradient of the failure line is increased from 1.08 to 1.32 with an increase in the degree of compaction, hence increasing the stability of slopes.
Read moreDilatancy and Strength of an Unsaturated Soil-Cement Interface in Direct Shear Tests
The dilatancy of a soil is significantly influenced by matric suction, and it affects the apparent friction angle and shear strength of the soil. To examine the influence of dilatancy on interface behavior, a series of direct shear box tests are conducted on a compacted completely decomposed granite (CDG) soil–grout interface in a cast in situ condition under different matric suctions and net normal stresses. The test results indicate that matric suction and net normal stress have significant influence on the hardening-softening and dilatancy of the soil–cement grout interface. The failure envelopes for different matric suctions are observed as linear. The apparent interface friction angle and adhesion intercept increase with matric suction. The suction envelope is found to be nonlinear as the δb-angle decreases with matric suction. A modified model is proposed to consider the influence of dilatancy on the apparent interface friction angle and hence on the interface shear strength. Experimental sh...
Read more