A time synchronized multi-robot coverage algorithm for unstructured environment

Bounding volume based approaches in velocity obstacle (VO) provide a good solution for collision avoidance of mobile robots with uncertainty. However, the VO built with the bounding footprint always has over-constraining problems which may lead to conservative maneuvers of the mobile robots. Addressing this problem, a vertical ellipse based velocity obstacle (VEVO) collision avoidance method is proposed in this paper. The method mitigates the over-constraining situation by building the footprint probability ellipse whose minor axis is vertical to the direction of the obstacle to minimize the VO area. Based on VEVO, a DWA (Dynamic Window Approach) integrated method is proposed to provide a set of available velocities in speed selection. According to different collision avoidance objectives like collision safety, shortest time consumption and shortest trajectory length, a multi-objective velocity selecting strategy is proposed to provide optimal velocities for motion planning. Furthermore, a dynamic local path adjustment method is proposed to help robots react to the closest obstacle (dynamic or static) according to different collision safety requirements. We validate our methods in a simulated workspace with different numbers of robots going to their goal points. Experimental results show VEVO method could improve the collision avoidance performance in crowded multi-robot environment and robots could achieve their different objectives when suitable parameters are set in the velocity evaluation function. The proposed dynamic local path adjustment method only affects the trajectories in local areas and could ensure collision avoidance safety and performance at the same time.

A control strategy for real-time collision avoidance of a mobile robot in an environment containing moving obstacles is proposed. Objects, including the robot, are modelled as convex polyhedra. Collision avoidance is guaranteed if the minimum distance between the robot and the objects is nonzero. A nominal trajectory is assumed to be known from offline planning. The main idea is to change the velocity along the nominal trajectory so that collisions are avoided. Consistency with the nominal plan is desirable. The process is formulated as an optimization problem and a close to optimal solution is obtained. >

This paper introduces a new behavior-based collision avoidance approach for mobile robot navigation in unknown and dynamic environments, which called Nearest Virtual-Target NVT. The NVT approach was developed based on a modeling-planning-reaction configuration. In modeling module, sensory information is integrated to construct a local model of environment which represents obstacles distribution and free obstacle areas in a part of robot's work space. The planning module uses the “actual-virtual target switching strategy” to compute obstacle free paths towards the target. The robot motion generation is handled by the reaction module. The reaction module applies a fuzzy controller to control the robot's rotational and translational velocities. The contribution of this approach is solving navigation difficulties presented in previous approaches for successful motion of the robot towards the target in troublesome scenarios such as narrow passages, very dense, cluttered and dynamic environments. Feasibility and effectiveness of the proposed approach are verified through simulation and real robot experiments. Eventually, advantages and limitations of this approach are discussed.

PurposeWheeled mobile robots (WMR) are the most widely used robots. Avoiding obstacles in unstructured environments, especially dynamic obstacles such as pedestrians, is a serious challenge for WMR. This paper aims to present a hybrid obstacle avoidance method that combines an informed-rapidly exploring random tree* algorithm with a three-dimensional (3D)-object detection approach and model prediction controller (MPC) to conduct obstacle perception, collision-free path planning and obstacle avoidance for WMR in unstructured environments.Design/methodology/approachGiven a reference orientation and speed, the hybrid method uses parametric ellipses to represent obstacle expansion boundaries based on the 3D target detection results, and a collision-free reference path is planned. Then, the authors build on a model predictive control for tracking the collision-free reference path by incorporating the distance between the robot and obstacles. The proposed framework is a mapless method for WMR.FindingsThe authors present experimental results with a mobile robot for obstacle avoidance in indoor environments crowded with obstacles, such as chairs and pedestrians. The results show that the proposed hybrid obstacle avoidance method can satisfy the application requirements of mobile robots in unstructured environments.Originality/valueIn this study, the parameter ellipse is used to represent the area occupied by the obstacle, which takes the velocity as the parameter. Therefore, the motion direction and position of dynamic obstacles can be considered in the planning stage, which enhances the success rate of obstacle avoidance. In addition, the distance between the obstacle and robot is increased in the MPC optimization function to ensure a safe distance between the robot and the obstacle.

A temporal planning algorithm that is implemented on a wheeled mobile robot is presented. This algorithm has two parts: the first part is developed to control the motion of the mobile robot, and the second part is designed to control a 6-degrees-of-freedom (DOF) arm attached to the robot. In most robotic applications, it is necessary for the mobile robot to plan and follow a desired path. It may also be necessary for the robot to follow a given velocity profile, which is known as temporal planning. The advantage of temporal planning method in this paper is in its simplicity and its computational efficiency. A rudimentary trajectory is first created by assigning an arbitrary time to each segment of the path. This trajectory is made feasible by applying a number of constraints and using a linear scaling technique. When a velocity profile is given, a nonlinear time scaling technique is used to fit the mobile robot’s linear velocity to the given velocity profile. A method for avoiding moving obstacles is also implemented. Simulation and experimental results showed good agreement with each other. A novelty of this paper is in developing and implementing a new method for control of a 6-DOF arm attached to the mobile robot. Two methods have been proposed and tested for position control of the robot arm; i) linear end-effector increment (LEI), and ii) linear joints increment (LJI). It is shown that LEI is more precise than LJI in trajectory tracking of robot arm; however, the singularity of Denavit-Hartenberg (DH) transformations matrix limits the application of this method for specific trajectories. The LJI is developed to avoid the singularity in DH transformation matrix. The experimental results for four different paths show the effectiveness of the LJI approach. The successful experimental results of path and temporal planning of a wheeled mobile robot and motion control of its industrial arm is reported.

There are many sources of uncertainty facing the fuzzy logic controller (FLC) for autonomous mobile robots navigating in changing and dynamic unstructured environments. The traditional type-1 FLC using precise type-1 fuzzy sets cannot fully handle such uncertainties. A type-2 fuzzy logic controller (FLC) using type-2 fuzzy sets can handle such uncertainties to produce a better performance. In this paper, we present the type-2 FLC and its novel application for the real time control of mobile robots. We used the type-2 FLC to implement different robotic behaviours on different robotic platforms in indoor and outdoor unstructured and challenging environments. The type-2 FLCs dealt with the uncertainties facing mobile robots in unstructured environments and resulted in a very good performance that outperformed the type-1 FLCs whilst using smaller rule bases.

There are some limitations in the practical application of robot obstacle avoidance control methods. In order to realize the high-speed planning and obstacle avoidance processing of mobile robot, the path model, inspection route and path obstacles of the robot must be fully considered. Through feature extraction, the reasonable planning of substation inspection obstacle avoidance route is realized, and the control quantity set satisfying substation inspection is given. The hierarchical fuzzy obstacle avoidance control method of mobile robot is realized by using the optimal control set design. The simulation results show that the control method can solve various complex problems when the robot contour collides with obstacles, and can realize safe and fast control. The flexibility and robustness of obstacle avoidance are improved, and the motion state and speed of obstacles are also improved.

This paper addresses the problems related to the mapless navigation control of wheeled mobile robots based on deep learning technology. The traditional navigation control framework is based on a global map of the environment, and its navigation performance depends on the quality of the global map. In this paper, we proposes a mapless Light Detection and Ranging (LiDAR) navigation control method for wheeled mobile robots based on deep imitation learning. The proposed method is a data-driven control method that directly uses LiDAR sensors and relative target position for mobile robot navigation control. A deep convolutional neural network (CNN) model is proposed to predict motion control commands of the mobile robot without the requirement of the global map to achieve navigation control of the mobile robot in unknown environments. While collecting the training dataset, we manipulated the mobile robot to avoid obstacles through manual control and recorded the raw data of the LiDAR sensor, the relative target position, and the corresponding motion control commands. Next, we applied a data augmentation method on the recorded samples to increase the number of training samples in the dataset. In the network model design, the proposed CNN model consists of a LiDAR CNN module to extract LiDAR features and a motion prediction module to predict the motion behavior of the robot. In the model training phase, the proposed CNN model learns the mapping between the input sensor data and the desired motion behavior through end-to-end imitation learning. Experimental results show that the proposed mapless LiDAR navigation control method can safely navigate the mobile robot in four unseen environments with an average success rate of 75%. Therefore, the proposed mapless LiDAR navigation control system is effective for robot navigation control in an unknown environment without the global map.

The construction of a smart autonomous mobile robot system that can operate in an anonymous environment can be difficult. Building an autonomous mobile robot requires collecting data from sensors and cameras in order to recognize the surrounding environment, get knowledge of existing landmarks, and figure out its position and orientation. Many research studies have been carried out in recent years providing algorithms for achieving autonomous motion of mobile robot systems and object detection. The most common platform utilized for robot motion design is ROS (Robot Operating System) and for object detection YOLO (You Only Look Once) is a common choice. Additionally, the autonomous system needs motion planning in a systematic way to avoid obstacles by using LIDAR or other sensing methods generating the feedback signals required for control of motion around occupied spaces. One of the most effective and versatile feedback systems for mobile robot control can be constructed using visual feedback, which relies on a high-resolution camera that processes the image in real-time and the result is fed back to the control system for decision making. Visual feedback can be employed alone without sensors for feedback control of autonomous mobile robots, and it can be used for multiple tasks like path planning, obstacle avoidance, object detection, object recognition in addition to motion control. In this research, results of design and construction of an autonomous mobile rescue robot for finding victims through video data are presented. It is aimed to find victims via applying video as a data collection and feedback generation tool in the autonomous mobile robot control system. The visual feedback and YOLO v3 are used not only for finding victims but also for motion control. Our autonomous mobile robot is designed to move smoothly to the victim's direction and avoids obstacles by using ROS Global Planner. The robot is tested in multiple scenarios in different locations, various obstacle and victim numbers, and satisfactory results with good performances are obtained.

In 2013 the Editor of Journal of Vibration and Control and SAGE became aware of a peer review ring involving assumed and fabricated identities that appeared to centre around Peter Chen at National Pingtung University of Education, Taiwan (NPUE). SAGE and the Editor then began a complex investigation into the case during the rest of 2013 and 2014. Following an unsatisfactory response from Peter Chen, NPUE was notified. NPUE were serious in addressing the Journal and SAGE’s concerns. NPUE confirmed that the institution was investigating Peter Chen. SAGE subsequently uncovered a citation ring involving the above mentioned author and others. We regret that individual authors have compromised the academic record by perverting the peer review process and apologise to readers. On uncovering problems with peer review and citation SAGE immediately put steps in place to avoid similar vulnerability of the Journal to exploitation in the future. More information may be found at www.sagepub.co.uk/JVC_Statement_2014 . The Journal and SAGE understand from NPUE that Peter Chen has resigned his post at NPUE. The following articles are retracted because after thorough investigation evidence points towards them having at least one author or being reviewed by at least one reviewer who has been implicated in the peer review ring and/or citation ring. All authors have had an opportunity to respond to the allegations and proposed actions. OnlineFirst articles (these articles will not be published in an issue) Chen CY, Chen T-H, Chen Y-H, Yu S-E and Chung P-Y (2013) Information technology system modeling an integrated C-TAM-TPB model to the validation of ocean tidal analyses Journal of Vibration and Control Epub ahead of print 7 May 2013. doi: 10.1177/1077546312472924 Chang R-F, Chen CY, Su F-P and Lin H-C (2013) A two-step approach for broadband digital signal processing technique Journal of Vibration and Control Epub ahead of print 26 April 2013. doi: 10.1177/1077546312472925 Chen TH, Chang CJ, Yu SE, Chung PY and Liu C-K (2013) Nonlinear information analysis and system management technique: the influence of design experience and control complexity Journal of Vibration and Control Epub ahead of print 12 April 2013. doi: 10.1177/1077546312473321 Chen CY, Shih BY, Chen YH, Yu SE and Liu YC (2013) The exploration of a 3T flow model using vibrating NXT: II. Model validation Journal of Vibration and Control Epub ahead of print 10 April 2013. doi: 10.1177/1077546312470481 Chen CY, Shih BY, Chen YH, Yu SE and Liu YC (2013) The exploration of 3T flow model using vibrating NXT: I. model formulation Journal of Vibration and Control Epub ahead of print 6 February 2013. doi: 10.1177/1077546312467360 Lin M-L and Chen C-W (2013) Stability analysis of fuzzy-based NN modeling for ecosystems using fuzzy Lyapunov methods Journal of Vibration and Control Epub ahead of print 6 February 2013. doi: 10.1177/1077546312466687 Chen CY, Chen TH, Chen YH and Chiu J (2012) A multi-stage method for deterministic-statistical analysis: a mathematical case and measurement studies Journal of Vibration and Control Epub ahead of print 20 December 2012. doi: 10.1177/1077546312466579 Shih BY, Lin MC and Chen CY (2012) Autonomous navigation system for radiofrequency identification mobile robot e-book reader Journal of Vibration and Control Epub ahead of print 13 December 2012. doi: 10.1177/1077546312466578 Chang RF, Chen CY, Su FP, Lin HC and Lu C-K (2012) Multiphase SUMO robot based on an agile modeling-driven process for a small mobile robot Journal of Vibration and Control Epub ahead of print 13 December 2012. doi: 10.1177/1077546312464993 Shih B-Y, Lin Y-K, Cheng M-H, Chen C-Y and Chiu C-P (2012) The development of an application program interactive game-based information system Journal of Vibration and Control Epub ahead of print 12 December 2012. doi: 10.1177/1077546312464682 Chen C-Y, Chang C-J and Lin C-H (2012) On dynamic access control in web 2.0 and cloud interactive information hub: technologies Journal of Vibration and Control Epub ahead of print 12 December 2012. doi: 10.1177/1077546312464992 Shin BY, Chen CY and Hsu KH (2012) Robot cross platform system using innovative interactive theory and selection algorithms for Android application Journal of Vibration and Control Epub ahead of print 13 November 2012. doi: 10.1177/1077546312463757 Articles published in an issue Chen C-W (2014) Applications of neural-network-based fuzzy logic control to a nonlinear time-delay chaotic system Journal of Vibration and Control 20 (4): 589-605. Epub ahead of print 5 November 2012. doi: 10.1177/1077546312461370 Chen C-W (2014) A review of intelligent algorithm approaches and neural-fuzzy stability criteria for time-delay tension leg platform systems Journal of Vibration and Control 20 (4): 561-575. Epub ahead of print 5 November 2012. doi: 10.1177/1077546312463759 Chen C-Y, Chang C-J and Lin C-H (2014) On dynamic access control in web 2.0 and cloud interactive information hub: trends and theories Journal of Vibration and Control 20 (4): 548-560. Epub ahead of print 5 November 2012. doi: 10.1177/1077546312463762 Lin M-L and Chen C-W (2014) Stability conditions for ecosystem modeling using the fuzzy Lyapunov method Journal of Vibration and Control 20 (2): 290-302. Epub ahead of print 23 October 2012. doi: 10.1177/1077546312451301 Chen C-H, Kuo C-M, Hsieh S-H and Chen C-Y (2014) Highly efficient very-large-scale integration (VLSI) implementation of probabilistic neural network image interpolator Journal of Vibration and Control 20 (2): 218-224. Epub ahead of print 22 October 2012. doi: 10.1177/1077546312458822 Chen C-Y (2014) Wave vibration and simulation in dissipative media described by irregular boundary surfaces: a mathematical formulation Journal of Vibration and Control 20 (2): 191-203. Epub ahead of print 22 October 2012. doi: 10.1177/1077546312464258 Chen C-H, Yao T-K, Dai J-H and Chen C-Y (2014) A pipelined multiprocessor system- on-a-chip (SoC) design methodology for streaming signal processing Journal of Vibration and Control 20 (2): 163-178. Epub ahead of print 16 October 2012. doi: 10.1177/1077546312458821 Lin M-L and Chen C-W (2014) Fuzzy neural modeling for n-degree ecosystems using the linear matrix inequality approach Journal of Vibration and Control 20 (1): 82-93. Epub ahead of print 8 October 2012. doi: 10.1177/1077546312458533 Chen C-H, Wu W-X and Chen C-Y (2013) Ant-inspired collective problem-solving systems Journal of Vibration and Control 19 (16): 2481-2490. Epub ahead of print 18 September 2012. doi: 10.1177/1077546312456231 Chen C-H, Yao T-K, Kuo C-M and Chen C-Y (2013) Evolutionary design of constructive multilayer feedforward neural network Journal of Vibration and Control 19 (16): 2413-2420. Epub ahead of print 12 September 2012. doi: 10.1177/1077546312456726 Chen C-W (2013) Applications of the fuzzy-neural Lyapunov criterion to multiple time-delay systems Journal of Vibration and Control 19 (13): 2054-2067. Epub ahead of print 16 August 2012. doi: 10.1177/1077546312451034 Chung P-Y, Chen Y-H, Walter L and Chen C-Y (2013) Influence and dynamics of a mobile robot control on mechanical components Journal of Vibration and Control 19 (13): 1923-1935. Epub ahead of print 20 July 2012. doi: 10.1177/1077546312452184 Chen C-W (2013) Neural network-based fuzzy logic parallel distributed compensation controller for structural system Journal of Vibration and Control 19 (11): 1709-1727. Epub ahead of print 22 June 2012. doi: 10.1177/1077546312442233 Chen C-W, Yeh K, Yang H-C, Liu KFR and Liu C-C (2013) A critical review of structural system control by the large-scaled neural network linear-deferential-inclusion-based criterion Journal of Vibration and Control 19 (11): 1658-1673. Epub ahead of print 18 June 2012. doi: 10.1177/1077546312443377 Chen C-H, Kuo C-M, Chen C-Y and Dai J-H (2013) The design and synthesis using hierarchical robotic discrete-event modeling Journal of Vibration and Control 19 (11): 1603-1613. Epub ahead of print 27 June 2012. doi: 10.1177/1077546312449645 Chang CJ, Chen CY and Chou I-T (2013) The design of information and communication technologies: telecom MOD strength machines Journal of Vibration and Control 19 (10): 1499-1513. Epub ahead of print 27 June 2012. doi: 10.1177/1077546312449644 Shih B-Y, Chen C-Y, Li K-H, Wu T-Y, Chen G-Y (2013) A novel NXT control method for implementing force sensing and recycling in a training robot Journal of Vibration and Control 19 (10): 1443-1459. Epub ahead of print 1 June 2012. doi: 10.1177/1077546312446361 Chen C-W, Chen P-C and Chiang W-L (2013) Modified intelligent genetic algorithm-based adaptive neural network control for uncertain structural systems Journal of Vibration and Control 19 (9): 1333-1347. Epub ahead of print 31 May 2012. doi: 10.1177/1077546312442232 Chen C-Y, Shih B-Y, Shih C-H and Wang L-H (2013) Enhancing robust and stability control of a humanoid biped robot: system identification approach. Journal of Vibration and Control 19 (8): 1199-1207. Epub ahead of print 26 April 2012. doi: 10.1177/1077546312442947 Chang C-J, Chen C-Y and Huang C-W (2013) Applications for medical recovery using wireless control of a bluetooth ball with a hybrid G-sensor and human-computer interface technology Journal of Vi

Retraction notice

Many bridges in Taiwan have been in use from the period that Taiwan was governed by the Japanese, over 50 years ago, which is the average ultimate usable lifetime of such structures. Three-quarters of the bridges on major highways have been in use for more than 20 years and numerous bridges on country roads have also been in use for more than 20 years. In other words, most of the bridges in Taiwan are aging and may require repair or replacement. Ambient vibration tests are utilized to measure the response of old bridges, which are difficult to equip with accelerometers. The Fourier transform method is traditionally used to gain important information about ambient vibration records. However, the development of information technology over the last 20 years has meant that there are more kinds of signal management technologies, including the wavelet and Hilbert—Huang transform (HHT) methods. In this study we investigate the characteristics of aging bridges by comparison with their structural properties. We analyze their ambient vibration, and discuss the possible influence of the frequency function. Long-term environmental impacts create many structural problems, but with traditional methods examination of bridge health is difficult. Therefore, in our HHT management system, we examine destroyed bridges. The characteristics and behavior of bridges subjected to random loading can be understood by analysis with the random decrement technique and the frequency response function method.

Retraction notice

This letter presents an adaptive coverage control strategy for multi-agent systems with obstacle avoidance in the presence of actuator faults and time-varying uncertainties. The strategy is based on a leader-follower approach. Assuming that the motion of the leader is given, one distributes the followers within the leader's obstacle-free sensing range so that collisions with obstacles can be avoided. An optimized distribution is achieved through the Centroidal Voronoi Tessellation (CVT) and a function approximation technique based immersion and invariance (FATII) coverage controller is constructed to realize the CVT. The stability of the FATII coverage controller is established and its validity is tested by simulations.

The objective of this research is to develop a real time obstacle detection and obstacle avoidance for autonomous navigation of mobile robots using a stereo camera in an unstructured environment. Autonomous navigation of mobile robots demands a) Exact determination of position and orientation of Robot and b) Accurate determination of size, shape, depth and range of potential obstacles in the environment. Simple kinematic model is used for mobile robot and stereo camera with pan and tilt provision is considered for long range operation. Complete 3D reconstruction of object/obstacle is obtained from the stereo matching algorithm and with triangulation method. The pose (position and orientation) of mobile robot is formulated from the static object observation with stereo reference matching points using RANSAC (RANdom SAmple Consensus) in successive frames. Potential field based obstacle avoidance formulation is carried out by using the obstacle range, size information, mobile robot position and orientation. Finally, proportional derivative navigation control loop along with obstacle avoidance algorithm is formulated and verified.