A Wide-Frequency Optical Fiber-Tip Vibration Sensor Based on Two-Photon 3-D-Printed Annular Resonant Cavity

This paper proposes the use of an fiber optic sensor (FOS) and electrorheological (ER) fluid actuator in the vibration active monitoring of smart composite structures. The intensity modulated fiber optic vibration sensor is developed following the face coupling theory. The characteristics of this optical fiber vibration sensor have been tested. The experimental results show that the new type intensity modulated optical fiber vibration sensor has higher sensitivity to measure the vibration frequency. At same time, our experimental investigations are focused on evaluating the elastodynamic response characteristics of a beam fabricated in an electrorheological fluid. It is noted that the most significant change in the material properties of ER fluid is the change of material stiffness and damping, which varies with the electric field intensity imposed upon ER fluid. Finally, the vibration of smart composite beam with embedded intensity modulated optical fiber vibration sensor and electrorheological fluids can be detected and controlled actively.

The detection of acoustic signals in the Martian environment is significant to understand the issues such as the evolution of the universe, structure of matter, origin of life, and future migration of humans. We proposed a method for testing ultrasonic wave by using fiber-optic Fabry-Perot vibration sensors in a low-pressure CO₂ environment. We conducted high-precision sound wave amplitude and speed measurement tests with different center frequencies at 21, 25, 34, and 40 kHz under different gas compositions, pressures, and distances. Results showed that under the conditions of 15 °C and gas pressure in the range of 600 Pa to 1 MPa, the measured average sound velocity of ultrasonic signals at each frequency was 268.79 m/s in the CO₂ environment, which was lower than the velocity of 336.18 m/s measured in the air environment. The results in this study can be applied to theoretical and experimental studies of future Mars probes pertaining to ultrasonic positioning and detection.

The paper proposes a version of realization for a fiber optic vibration sensor. The sensor possesses a wide range of operation frequencies with such interrogation devices as optical power meters. In comparison to spectral measuring complexes, the sensor imposes lower requirements on operating conditions. The authors investigated a sensing head based on a fiber SMF-MMF-SMF structure and a fiber Bragg grating inscribed in this structure. The external vibration frequency applied to the tested sensor structure is obtained using the Fourier transform of the signal received from the photodetector. The structure designed in this study with a fiber Bragg grating inscribed in it can be used as a sensing head of a fiber optic vibration sensor. It is demonstrated that the sensor based on the developed sensitive structure is able to obtain the external vibration frequency in the range of 20-9 000 Hz with accuracy up to 1 %. The research results are essential for monitoring systems for the state of structural elements of buildings and structures. The implementation of the vibration sensor in the format of a fiber optic device allows overcoming the limitations of piezoelectric sensors, providing high noise immunity and resistance to harsh environmental effects.

This paper proposes the use of a fiber optic sensor (FOS) and electrorheological (ER) fluid actuator for vibration monitoring of smart composite structures. A new intensity modulated fiber optic vibration sensor is developed following the face coupling theory. It has high sensitivity similar to the traditional piezoelectric sensor. Also it is lower in cost. The experiment of vibration control of smart composite beam with embedded intensity modulated optical fiber vibration sensor and ER fluids are described in this paper. It is noted that the most significant change in the structural properties of smart composite beam is the change of structural damping and natural frequency, which varies with the electric field intensity imposed upon ER fluid. So the structural vibration can be monitored and controlled effectively utilizing FOS and ER fluids.

Fiber optic sensors, prized for their light weight, compact size, high temperature resilience and resistance to electromagnetic interference, find extensive utility in various measurement applications. The performance of these sensors is primarily contingent on their sensitive units, with distinct structures of these units yielding varied performance outcomes. Traditional design methods primarily rely on finite element simulation and optimization, which are subjective and inefficient. Thus, the efficient on-demand design of sensitive structures is essential for different application scenarios. Here, we present a novel approach for both forward performance prediction and inverse structure design employing deep learning techniques based on symmetric bidirectional neural networks, with fiber optic vibration sensors serving as a design example. The proposed method can address the non-unique solution in traditional deep learning techniques for inverse design of three-dimensional (3D) complex structures. By learning the underlying relationships between complex non-intuitive sensitive structures and their performances, the approach can eliminate the need for numerous costly calculations that heavily depend on human experience or intuition. Furthermore, compared to the response surface optimization method, this approach saves 21.1 times the computation time and has an accuracy improvement of 34.6% when dealing with six samples. The results show that the efficiency of fiber optic sensor design can be significantly improved by employing this novel deep learning technique, which offers new insights for the rapid advancement of the fiber optic sensing field.

In the petrochemical industry, delayed cooking is an important production process. This paper analyzes the principle of FBG vibration sensor. The automatic monitoring system of hydraulic defocusing is studied based on fiber optic vibration sensor. The fiber optic sensing system can detect the removal of coke in the coke tower automatically, and it can reduce the labor intensity of workers. It can also improve the automation level of real-time monitoring of hydraulic decoking system.

A stable homodyne interferometric fiber optic vibration sensor is proposed and demonstrated by using a probe pulse, which is generated based on random phase modulation. The first half of the probe pulse is divided into three time slots. Each time slot is subjected to random and different phase modulation. The last half of the probe pulse is not modulated. An unequal-arm Michelson interferometer is used as the sensing unit of vibration sensor. By using a simple direct detection scheme, the interference signals of three time slots can be distinguished in the time domain. Two time slots' interference signals are selected and extracted as the signal to be demodulated. The vibration signal to be measured can be quantitatively measured by using ellipse fitting algorithm and arctangent algorithm. Compared with the traditional 3 × 3 coupler-based scheme, the system structure is simple and can form a large-scale sensor array. Moreover, the interference light signal in each time slot can provide multiple channels for averaging, resulting in a better demodulation signal-to-noise ratio (SNR) performance. By multi-channel averaging, the SNR is improved by at least 5.2 dB.

A new fiber-optic extrinsic Fabry-Perot microinterferometer cantilever beam type vibration sensor (EFPI-V) is described. For eliminating signal fading effects a two-wavelength demodulation scheme is implemented. The theoretical model of this sensor with pronounced eigenfrequency spectrum in the acoustic range is confirmed by experimental results. Initial field tests in an experimental airport ground traffic surveillance system for vehicle defection via monitoring of structural vibrations demonstrate the application as traffic sensor.

Analysis of the vibrational characteristics of materials or mechanical systems had the promise of providing useful information of their integrity. Acoustic monitoring of heavy machine bearings is a well-established technique for detecting the onset of wear [1]. Damage to materials [2] or structures [3] results in local stiffness reductions which may be detected by measuring their dynamic response. Vibration sensors could also be used to monitor the passage of traffic over bridges and roadways or for security applications such as detecting forced entry into buildings. Vibration sensing is most commonly performed by electromechanical devices such as piezoelectric, piezoresistive or capacitative accelerometers. Whilst this is reliable and tested technology it has a potential drawback. Susceptibility to electromagnetic interference limits application around strong electric fields and the need for either strongly shielded leads or a power supply for a built-in amplifier results in relatively heavy, bulky cables. If an extensive network of sensors is to be incorporated into a structure, this may prove to be a considerable problem, even more so if there is a premium on weight, as in aerospace structures. Optical fibre sensors have been shown to be suited for embedment in composites [4] and cementitious materials [5]. They have largely unaffected electromagnetic interference and in some cases they may be multiplexed to give a distributed sensing system. Optical fibre sensors tend to be more expensive than their conventional counterparts, mainly because the equipment needed to interrogate the sensor is often delicate and complex. To measure vibration, either a strain gauge-type device is attached intimately to the structure to measure surface acoustic waves, or a fibre-optic accelerometer is employed in place of a conventional one. The device presented in this latter modulates the intensity of light transmitted through it and thus requires only simple and cheap instrumentation. It is illustrated schematically in Fig. 1. The details of its construction and operation are as follows. Two 50=125 multimode optical fibres are cleaved and the protective polymer jacket of one of the fibres is stripped back a short length. The prepared fibres are then inserted into a precisiondrawn glass capillary, their end-faces separated by a few tens of microns, and fixed with epoxy resin adhesive. When the sensor is subjected to an acceleration prependicular to the axes of the optical fibres, the motion of the unsupported fibre lags behind. As it moves out of alignment, relative to the fixed fibre, the transmitted optical power decreases. The power variations are detected with a fastresponse photodiode and amplifier and sent to a personal computer for further processing. The response of the sensor to sinusoidal and transient excitation was investigated. First, the sensor was mounted on an electromagnetic coil which was driven by a signal generator and amplifier and excited over a range of frequencies from 100 to 10000 Hz. The sensors which provided the results presented here had resonant frequencies of 3 Hz and 6 Hz, but this value can be varied by changing the length of the cantilevered fibre or by choosing fibres of different diameters. To test the response to transients, sensors of 3 Hz resonant frequency were bonded to the surface of 70 3 70 mm 16-ply crossply carbon-fibre reinforced plastic (CFRP) with a cyanoacrylate adhesive. An impulse was provided by either dropping a 6.3 mm diameter steel ball onto the panel from a height of 25 cm, giving an impact energy of 2.5 mJ, or a standard pencil break test [6]. Examples of sensor signals from these events are given in Fig. 2. The impact of the steel ball, considerably the more energetic of the two events, gave a greater signal amplitude, as well as a characteristic shape different from that of the pencil break. Results were consistent within both series, with the pencil break showing a little more variability.

An intensity modulation-based fiber optic vibration sensor (FOVS) using serpentine spring with proof mass structure is proposed and demonstrated via experiments. The structure, operating principle, and characteristics of the proposed sensor are given.

In recent years, phase demodulation methods for optical fiber vibration sensors (OFVS) have attracted more and more attention, aiming to accurately detect vibration signals. The principles of phase modulation and demodulation in OFVS are firstly introduced. Then, three classical phase demodulation methods are described, including phase generated carrier (PGC) demodulation method, <inline-formula> <tex-math notation="LaTeX">${3}\,\,\times \,\,{3}$ </tex-math></inline-formula> coupler demodulation method, and in-phase and quadrature (IQ) demodulation method. Furthermore, the state of art of phase demodulation methods in various OFVS are reviewed. As the results of analysis, different structures of OFVS need appropriate demodulation methods for vibration detection. The Fourier transform method, fringe counting method and PGC demodulation method have strong applicability for Fabry-Perot interference OFVS. The scalability of interferometers provides convenience for PGC demodulation method and <inline-formula> <tex-math notation="LaTeX">${3}\,\,\times \,\,{3}$ </tex-math></inline-formula> coupler demodulation method in the OFVS with composite structure. PGC demodulation method, <inline-formula> <tex-math notation="LaTeX">${3}\,\,\times \,\,{3}$ </tex-math></inline-formula> coupler demodulation method and quadrature demodulation method are good choices for dynamic sensing in FBG-OFVS. The IQ demodulation method is a popular choice for phase sensitive optical time domain reflectometry at present. This paper provides a reference for the OFVS to realize vibration detection with appropriate phase demodulation method.

Vector vibration sensing is playing an increasingly important role in scientific measurement and engineering applications. Due to their outstanding intrinsic merits of electromagnetic immunity, remote operation capability, compact size and high sensitivity, fiber-optic vibration sensors have attracted much attention. In this paper, a two-dimensional vector vibration sensor based on multi-core fiber (MCF) Bragg gratings is proposed. The sensor can obtain the vibration azimuthal angle and the acceleration by monitoring the wavelength shifts of two cores of the MCF. The resonance frequency of the proposed sensor is 18Hz, and the linear sensitivity is 73.8 pm/g at 30 Hz. Moreover, it can be easy to realize multiple point-position cascaded multiplexing owing to the compliant cylindrical structure.

A novel fiber optic vibration sensor is presented, based on the motion detection of an elastic cantilever by means of the optical triangulation technique. The sensor was designed to work at a fixed frequency of 100 Hz for applications in high power electrical plants where insulation and EM immunity requirements make fiber optic sensing the most suitable choice. The working linear range reaches a peak amplitude of 0.25 mm; resolution is 0.1 microm; accuracy is better than +/-3%; and sensitivity is 10 mV/microm. Design details and experimental results are reported.

Coupled neurons with multi-objective optimization benefit incipient fault identification of machinery

Non contact optical techniques have been extensively used in vibration sensing for a number of years, especially for the measurement of small amplitude vibrations [1]. Optical probing of the vibrating component has the advantage of being extremely sesnittive with a large dynamic range.