Accuracy Performance Analysis between War Driving and War Walking in Metropolitan Wi-Fi Localization

Wireless fingerprinting localization (FL) systems identify locations by building radio fingerprint maps, aiming to provide satisfactory location solutions for the complex environment. However, the radio map is easy to change, and the cost of building a new one is high. One research focus is to transfer knowledge from the old radio maps to a new one. Feature-based transfer learning methods help by mapping the source fingerprint and the target fingerprint to a common hidden domain, then minimize the maximum mean difference (MMD) distance between the empirical distributions in the latent domain. In this paper, the optimal transport (OT)-based transfer learning is adopted to directly map the fingerprint from the source domain to the target domain by minimizing the Wasserstein distance so that the data distribution of the two domains can be better matched and the positioning performance in the target domain is improved. Two channel-models are used to simulate the transfer scenarios, and the public measured data test further verifies that the transfer learning based on OT has better accuracy and performance when the radio map changes in FL, indicating the importance of the method in this field.

Recently, indoor localisation techniques that use wireless local area network (WLAN) be a-con signals have gained much attention by the research communities. Many localisations methods are used to estimate the user of mobile device in indoor environments. However, the accuracy of these methods is affected by the nature of the test-bed environment. In this paper, we introduce an experimental test-bed in a typical indoor environment. We used a finger printing-based localisation algorithm to estimate the user location. The fingerprinting technique consists of two phases: offline phase and online phase. In the offline phase, calibration points are collected at certain places in floor to build a radio map. In the online phase, deterministic and probabilistic approaches are applied in order to get the correct estimated position of a mobile device. In deterministic approach, the position of mobile device estimated by K-nearest neighbour (KNN). In probabilistic approach, the position of mobile device estimated by Bayesian network (BN). Clustering technique is proposed to improve the system's accuracy and reduce the radio map size in the offline phase. We present experimental results that improved the system accuracy and reduce the size of radio map by using the proposed clustering technique.

Localization of users in indoor spaces is a common issue in many applications. Among various technologies, a Wi-Fi fingerprinting based localization solution has attracted much attention, since it can be easily deployed using the existing off-the-shelf mobile devices and wireless networks. However, the collection of the Wi-Fi radio map is quite labor-intensive, which limits its potential for large-scale application. In this paper, a visual-based approach is proposed for the construction of a radio map in anonymous indoor environments. This approach collects multi-sensor data, e.g., Wi-Fi signals, video frames, inertial readings, when people are walking in indoor environments with smartphones in their hands. Then, it spatially recovers the trajectories of people by using both visual and inertial information. Finally, it estimates the location of fingerprints from the trajectories and constructs a Wi-Fi radio map. Experiment results show that the average location error of the fingerprints is about 0.53 m. A weighted k-nearest neighbor method is also used to evaluate the constructed radio map. The average localization error is about 3.2 m, indicating that the quality of the constructed radio map is at the same level as those constructed by site surveying. However, this approach can greatly reduce the human labor cost, which increases the potential for applying it to large indoor environments.

One of the problems associated with the implementation of indoor location detection systems is the time-consuming procedure of equipment adjustment, which includes indoor map construction, radio signal map creation and calibrating signal propagation model. Thus, the equipment adjustment is a time-consuming and expensive process to be perform every time when there are changes in equipment configuration and allocation. The developed indoor localization system provides navigation of the user inside a room and allows to building radio map and putting Bluetooth Low Energy (BLE) beacons on the map of a room by the efforts of a number of users walking indoors. The architecture of the system is developed so that the different indoor localization techniques can be used and different services can be requested by the user’s mobile application. The user’s navigation inside the room is a combination of PDR based on the built-in smartphone sensors, multilateration and fingerprinting. The indoor navigation ontology is implemented to make decision which of these methods should be used. The key feature of the system is determining the location of BLE beacon. For this purpose the Random Forest algorithm is used, which uses signal levels, user rotation angles and distance to Bluetooth beacon as a training dataset. The geometric parameters of a room are estimated by the radio map and Bluetooth beacon locations.

Due to the heavy workload of RSS collection, the instability of WLAN signal strength and the disappearance of signals caused by complex indoor environments, the construction of radio map for wireless local area network (WLAN) fingerprint-based indoor positioning system is time-consuming and laborious. In order to rapidly deploy indoor WLAN positioning system, the bidirectional encoder representation from transformers (BERT) model is used to fill the missing signal in radio map and quickly build radio map. The radio map is imported into the BERT model in the form of natural language text, and the missing signal is filled by the BERT model. Since the number of input data in BERT model cannot exceed 512 words, the structure of BERT model is not suitable for WLAN signals with large data volume. Therefore, we redefine the model structure based on the original BERT model and fill in the missing signals in the radio map in parallel. In addition, the loss function is redefined. Except that each segment has a loss function, the weighted average value of all segment loss functions is defined as the total loss function. The experimental results show that the BERT model is better than the traditional linear interpolation method, compressed sensing algorithm and matrix completion algorithm in filling the missing signals in the fingerprint database, and the probability of error within 2 m reaches about 94%.

The construction and update of a radio map are usually referred as the main drawbacks of WiFi fingerprinting, a very popular method in indoor localization research. For radio map update, some studies suggest taking new measurements at some random locations, usually from the ones used in the radio map construction. In this paper, we argue that the locations should not be random, and propose how to determine them. Given the set locations where the measurements used for the initial radio map construction were taken, a subset of locations for the update measurements is chosen through optimization so that the remaining locations found in the initial measurements are best approximated through regression. The regression method is Support Vector Regression (SVR) and the optimization is achieved using a genetic algorithm approach. We tested our approach using a database of WiFi measurements collected at a relatively dense set of locations during ten months in a university library setting. The experiments results show that, if no dramatic event occurs (e.g., relevant WiFi networks are changed), our approach outperforms other strategies for determining the collection locations for periodic updates. We also present a clear guide on how to conduct the radio map updates.

A numerical simulation tool for predicting the impact of outdoor thermal environment on building energy performance

The scenic spot contains complex and changeable indoor and outdoor environments, some of which may be difficult to work effectively due to signal occlusion, multipath effect and other factors. In response to this problem, this paper proposes a method of Location Identification Based on the Dynamic Active Radio Frequency IDentification Calibration system and fingerprint localization system. It aims to improve positioning accuracy and reliability in the complex environment in the scenic spot. Firstly, the Location Identification Based on Dynamic Active Radio Frequency IDentification Calibration system is analyzed and improved. Then the improved positioning algorithm is applied to the complex environment of the scenic spot. Finally, the positioning results of the improved positioning algorithm in the complex environment of the scenic spot are tested. The experimental results show that when the K value is set to 4, the reader is arranged in the four corners and the center of the area, and the label density is set to 6×6, the average error of the research system in terms of error control is only 0.32, which is 0.28 less than that of the ultrasonic positioning system. All in all, the combination of Location Identification Based on Dynamic Active Radio Frequency IDentification Calibration system and traditional location fingerprint location of the scenic spot complex environment positioning scheme, it has shown great advantages in positioning accuracy, stability and real-time.

Wireless local area network (WLAN) fingerprinting has been extensively studied for indoor localization due to the formidable deployability of WLAN in indoor environment, but one major bottleneck of its practical implementation is the extensive calibration effort required to construct the radio map through the fingerprinting which is time consuming and labor intensive. In response to this compelling problem, we newly design the graph-based semi-supervised manifold alignment approach which relies on the concept of graph construction to construct a cost-efficient radio map with a small number of labeled fingerprints. In addition, the unlabeled user traces are also considered to compensate for the sparsity of the raw radio map as well as enhance its robustness to the environmental change. The extensive experiments conducted in an actual indoor WLAN environment demonstrate the performance improvement (by 27.48% at most with respect to the confidence probability of errors within 3 m) by our system compared with the existing ones using the fingerprints solely.

Automated radio telemetry systems are one of the most widely applicable methods for tracking wildlife at fine spatiotemporal scales. A growing trend is for these systems to apply large networks of receivers to detect radio signal strength (RSS) from radio‐tagged individuals. Analytical methods to derive position estimates using RSS localisation, however, are relatively underdeveloped in the field of wildlife tracking. Here, we apply approaches from indoor positioning systems to develop a new method, radio fingerprinting, for localising radio‐tagged animals in structurally complex, outdoor environments. This method characterises the RSS patterns at known locations to generate a radio map of the study area, which is then used to predict the location of new RSS patterns. We conducted field tests to evaluate the localisation accuracy of radio fingerprinting relative to multilateration, a commonly used method for RSS localisation. To do so, we established an experimental receiver network covering multiple habitat types and compared the localisation accuracy of radio fingerprinting to multilateration. Additionally, we evaluated how a variety of features characteristic of typical tracking data sets affected the accuracy of both methods. While both methods had a similar median error under ideal conditions (~30 m), radio fingerprint localisation method offered several advantages over multilateration. Multilateration localisation estimates were highly affected by missed detections from the nearest receiver to the test point, which occurred in 30% of cases. In these cases, the median error was 103 m, over a 3.5‐fold increase. Distance to the nearest receiver also biased multilateration estimates with error increasing as the distance increased. Additionally, errors from multilateration estimates were higher in more densely vegetated areas. In contrast, fingerprinting position estimates were largely robust to each of these scenarios. Automated radio telemetry enables the fine‐scale, continuous tracking of range‐resident animals. We present radio fingerprinting as a localisation method in outdoor environments where standard localisation methods are error‐prone due to habitat heterogeneity and missed detections. This approach can be applied to any automated radio telemetry hardware and to any study system where a radio map can be generated.

Providing high data rates and wide bandwidth applications are the most important challenges that mobile systems and radio networks are trying to accomplish. Radio over Fiber-RoF systems is a promoting research field since it benefits of Passive Optical Network (PON) advantages and unlicensed large bands in 60 GHz millimeter band (57-64GHz). In this study, we consider a complete RoF system from the central office to the end-user passing by the base station and we study the impact of propagation environment on the whole system performance and radio coverage by considering different scenarios for multipath propagation (Line of Sight-LOS, Non Line of Sight-NLOF). In particular, we have been interested in Rayleigh and Rice propagation models for both indoor and outdoor environments. Optisystem/ADS Co-simulation has been investigated to simulate RoF network coverage for indoor and outdoor environments while considering high data rates.

Region clustering based fingerprint model for flexible Wi-Fi fingerprinting

A Wi-Fi fingerprint consists of received signal strength values at a particular location along with the location information. A Wi-Fi radio map is constructed by maintaining a database of Wi-Fi fingerprints at various points in a building. A city radio map is a collection of radio maps for most buildings in a city. A highly precise citywide indoor positioning service is possible, if an accurate city radio map is available. However, tremendous time and effort are required to construct a city radio map through manual calibration. This paper proposes a method for constructing a city radio map through the crowdsourcing of Wi-Fi fingerprints from numerous smartphones. The proposed method classifies the buildings in a city into three categories: buildings in residential areas, commercial areas, and public areas. Then, it develops location-labeling techniques appropriate for the collected fingerprints from buildings in each category. Experiments conducted in the cities of Daejeon and Seoul revealed that the proposed method can construct a precise city radio map with minimal cost in a short period of time. Once city radio maps are constructed for most cities around the world, the global indoor positioning system will be completed.

Radio channel state information (CSI) measured with many receivers is a good resource for localizing a transmitter device with machine learning with a discriminative model. However, CSI localization is nontrivial when the radio map is complicated, such as in building corridors. This article introduces a view-selective deep learning (VSDL) system for indoor localization using CSI of WiFi. The multiview training with CSI obtained from multiple groups of access points (APs) generates latent features on a supervised variational deep network. This information is then applied to an additional network for dominant view classification to minimize the regression loss of localization. As noninformative latent features from multiple views are rejected, we can achieve a localization accuracy of 1.28 m, which outperforms by 30% the best known accuracy in practical applications in a complex building environment. To the best of our knowledge, this is the first approach to apply variational inference and to construct a practical system for radio localization. Furthermore, our work investigates a methodology for supervised learning with multiview data where informative and noninformative views coexist.

IoT Enabled Automated Object Recognition for the Visually Impaired