An Application of Throughput Request Satisfaction Method for Maximizing Concurrent Throughput in WLAN for IoT Application System.

Currently, Internet of Things (IoT) has become common in various applications, including smart factories, smart cities, and smart homes. In them, wireless local-area networks (WLANs) are widely used due to their high-speed data transfer, flexible coverage ranges, and low costs. To enhance the performance, the WLAN configuration should be optimized in dense WLAN environments where multiple access points (APs) and hosts exist. Previously, we have studied the active AP configuration algorithm for dual interfaces using IEEE802.11n and 11ac protocols at each AP under non-channel bonding (non-CB). In this paper, we study the algorithm considering the channel bonding (CB) to enhance its capacity by bonding two channels together. To improve the throughput estimation accuracy of the algorithm, the reduction factor is introduced at contending hosts for the same AP. For evaluations, we conducted extensive experiments using the WIMENT simulator and the testbed system using Raspberry Pi 4B APs. The results show that the estimated throughput is well matched with the measured one, and the proposal achieves the higher throughput with a smaller number of active APs than the previous configurations.

The mobility and ubiquitous access afforded by wireless local area networks (WLANs) and high-performance portable products promise to revolutionize the way we live, work, and play. However, sustained improvements in the throughput of WLANs, while also supporting robust long-range operation, requires the use of multiple antennas at both the mobile terminal and the access point. This article reviews the various space-time coding and decoding technologies employed for capitalizing on the increased capacity of the multiple-input multiple-output (MIMO) radio channel. Also described is a channel sounding campaign performed in the office environments used to scope the expected performance of these space-time codes in realistic deployments.

Wireless Gigabit (WiGig) access points (APs) using 60 GHz unlicensed frequency band are considered as key enablers for future Gbps wireless local area networks (WLANs). Exhaustive search analog beamforming (BF) is mainly used with WiGig transmissions to overcome channel propagation loss and accomplish high rate data transmissions. Due to its short range transmission with high susceptibility to path blocking, a multiple number of WiGig APs should be installed to fully cover a typical target environment. Therefore, coordination among the installed APs is highly needed for enabling WiGig concurrent transmissions while overcoming packet collisions and reducing interference, which highly increases the total throughput of WiGig WLANs. In this paper, we propose a comprehensive architecture for coordinated WiGig WLANs. The proposed WiGig WLAN is based on a tight coordination between the 5 GHz (WiFi) and the 60 GHz (WiGig) unlicensed frequency bands. By which, the wide coverage WiFi band is used to do the signaling required for organizing WiGig concurrent data transmissions using control/user (C/U) plane splitting. To reduce interference to existing WiGig data links while doing BF, a novel location based BF mechanism is also proposed based on WiFi fingerprinting. The proposed coordinated WiGig WLAN highly outperforms conventional un-coordinated one in terms of total throughput, average packet delay and packet dropping rate.

The Global Positioning System (GPS) has eventually become a common positioning technology. While GPS enabled many applications, satellite signals have yet to overcome many obstacles to enable indoor positioning. Meanwhile, due to the wide deployment of Wireless Local Area Networks (WLAN) in recent years, WLAN positioning algorithms have become popular for mobile device positioning in indoor environments. The most accurate WLAN positioning algorithms exploit the so-called fingerprinting concept which consists of two stages. In the offline stage (training), the Received Signal Strength Indicator (RSSI) from a set of available Access Points (AP) is measured for a number of reference locations and stored in a database. Due to the availability of many APs and the complex structure of indoor environments, this information is distinctive for each reference location and thus is called a position fingerprint. In the online stage (testing), a mobile device receives RSSIs from the APs and their fingerprint is compared to the fingerprints that are stored in the database for a best possible match. WLAN fingerprinting can provide high accuracy in indoor environments when there are many APs which ensure fingerprint uniqueness. This paper provides a novel approach to use WLAN multipath signals as possible fingerprints for positioning algorithms for applications with lower number of access points. The paper provides an initial study.

The idea of smart and sustainable cities is incomplete without using information and communication technologies. Wireless Local Area Network (WLAN) plays a vital role in connecting different services, transferring data and providing indoor localization. WLAN fingerprinting technique has become the most common approach for indoor localization in smart cities. This technique utilizes received signal strength (RSS) and channel status from the installed WLAN Access Points (AP). Currently, WLAN planning relies on the site survey, which is laborious and uneconomical for large areas. The WLAN has a limited number of channels assigned in the frequency reuse strategy. An inefficient channel assignment strategy will lead towards increased interference, thus degrading the overall service. This paper proposes a WLAN channel assignment strategy for large and crowded indoor areas. The proposed scheme assigns the channels to installed APs for indoor localization in fingerprinting framework. The proposed technique ensures that the proposed AP channel assignment algorithm in our network-planning scheme mitigates interference.

It is usually possible to associate with more than one Access Point (AP) in IEEE 802.11 Wireless LANs. AP selection is a crucial issue because the performance achieved by a user heavily depends on the AP selected. A received signal strength (RSS)-based association mechanism is specified by the IEEE 802.11 standard. However, this does not consider the channel conditions and AP load, which leads to a low throughput and a low user transmission rate. An alternative to using the RSS is to exploit the airtime metric, which provides users with information on how busy the channel is, but the results of our simulations show that the airtime metric cannot indicate the exact status of the channel. In this paper, we present a new association framework using channel occupancy in order to provide users with exact channel status information of APs. Via the proposed scheme, users can compare the achievable throughput provided by each AP and select the best AP. We validate our proposed association method via simulation results, which show that the throughput improvement of the method is worthy of notice.

With the rapid proliferation of broadband wireless services, it is of paramount importance to understand how fast data can be sent through a wireless local area network (WLAN). Thanks to a large body of research following the seminal work of Bianchi, WLAN throughput under saturated traffic condition has been well understood. By contrast, prior investigations on throughput performance under unsaturated traffic condition was largely based on phenomenological observations, which lead to a common misconception that WLAN can support a traffic load as high as saturation throughput, if not higher, under nonsaturation condition. In this paper, we show through rigorous analysis that this misconception may result in unacceptable quality of service: mean packet delay and delay jitter may approach infinity even when the traffic load is far below the saturation throughput. Hence, saturation throughput is not a sound measure of WLAN capacity under nonsaturation condition. To bridge the gap, we define safe-bounded-mean-delay (SBMD) throughput and safe-bounded-delay-jitter (SBDJ) throughput that reflect the actual network capacity users can enjoy when they require finite mean delay and delay jitter, respectively. Our earlier work proved that in a WLAN with multi-packet reception (MPR) capability, saturation throughput scales superlinearly with the MPR capability of the network. This paper extends the investigation to the nonsaturation case and shows that superlinear scaling also holds for SBMD and SBDJ throughputs. Our results here complete the demonstration of MPR as a powerful capacity-enhancement technique for WLAN under both saturation and nonsaturation conditions.

Indoor positioning methods using location-sensitive features of available wireless signals can achieve high accuracy. In particular, many state-of-the-art methods exploit quite unique sets of location-dependent received signal strength (RSS) measurements from multiple wireless local area network (WLAN) access points (APs), also called as wireless fingerprints. However, reception of signals from WLAN APs is not often stable, and RSS measurements tend to be unavailable due to WLAN card or AP transient effects, limited sensitivity of WLAN cards, and fluctuating attenuation and reflection of signals due to a multipath environment, structural changes and moving objects. In certain hostile scenarios, bogus APs may be installed to disorient WLAN localisation algorithms. In this study, two approaches are proposed to mitigate the impact of faulty signal strength measurements. Performance figures are provided for both simulated and empirical environments in order to support conclusions.

As smart building becomes increasingly popular, it enables many interesting applications, such as smart lock, elderly monitoring and remote healthcare.This paper will introduce one sub-system in the smart building: smart power system.This smart power system consists of an Android application, a cloud server and a smart socket.In addition, human-device interaction methods in this system are studied.

IEEE 802.11 Wireless Local Area Networks (WLANs) has become one of the most popular networking environments. With high density WLANs, it causes the interference among access points (APs) and degrades the performance of APs, especially in public area. To solve this problem, we design and implement a Cluster-based Channel Assignment (CCA), a combination of RSS-Aware Channel Selection Module (RCSM) and Interference-Aware Clustering Module (ICM), which is applied to a network management system (NMS) as a central coordinator. Based on the Received Signal Strength (RSS) information collected by NMS, RCSM can assign channels with less interference and ICM can reasonably partition interference domains of WLANs. The CCA leads to more efficient channel assignment in high density WLANs. We applied our scheme in a high density real Public WLANs, called Huashan. The results show it effectively increases the AP's throughput.

Internet of things is the trending direction when it comes to designing smart living environment. One of the popular applications of Internet of things is the smart home system. A smart home system usually consists of various types of connected sensors, actuators, appliances and a controller. The controller analyzes the data reported by the sensors and sends out messages to electric appliances and other sensors to ask them to behave accordingly. There are a lot of smart home designs proposed in the literature to make the systems smarter and more comfortable. However, little work has considered the security and privacy issues in smart home systems. In this paper, we analyze the differences of security and privacy issues that lie in the smart home systems, smart grid, and wireless sensor networks. Further, we propose our own solutions that achieves privacy preservation during the communications between end sensors and appliances and the controller.

Indoor localization based on Received Signal Strengths (RSS) or on some form of power measurements is a low-cost and low-complexity solution gaining more and more interest in the research and commercial worlds. Typically, Wireless Local Area Network (WLAN) signals are employed for such purpose, due to the fact that they are widely spread in indoor environments. Nevertheless, any wireless signal available in indoor scenarios can be used for positioning based on similar power measurement approaches. One example is the radio frequency identification (RFID), which enable portable localization systems in the form of wearable REID tags. Such RFID-enabled systems are highly demanded for health-state monitoring, object tracking, and security. These applications are mostly indoor applications, and thus, we can envision a near future where multiple RFID and WLAN signals will co-exist on multiple frequency bands. The existing signal diversity can offer a benefit in indoor positioning, providing that the signal propagation effects for both WLAN and RFID are well understood and taken into account. However, measurement-based studies on indoor channel modeling, including path loss and shadowing effects of RFID signals are still missing. A comparison between RFII) and WLAN channel models for positioning purpose has yet to be made. It is the purpose of our paper to address the path-loss channel models and shadowing effects for WLAN and RFID signals based on extensive measurement campaigns in an office environment.

Due to the wide deployment of wireless local area networks (WLAN), received signal strength (RSS)-based indoor WLAN localization has attracted considerable attention in both academia and industry. In this paper, we propose a novel page rank-based indoor mapping and localization (PRIMAL) by using the gene-sequenced unlabeled WLAN RSS for simultaneous localization and mapping (SLAM). Specifically, first of all, based on the observation of the motion patterns of the people in the target environment, we use the Allen logic to construct the mobility graph to characterize the connectivity among different areas of interest. Second, the concept of gene sequencing is utilized to assemble the sporadically-collected RSS sequences into a signal graph based on the transition relations among different RSS sequences. Third, we apply the graph drawing approach to exhibit both the mobility graph and signal graph in a more readable manner. Finally, the page rank (PR) algorithm is proposed to construct the mapping from the signal graph into the mobility graph. The experimental results show that the proposed approach achieves satisfactory localization accuracy and meanwhile avoids the intensive time and labor cost involved in the conventional location fingerprinting-based indoor WLAN localization.

Queueing systems to study the energy consumption of a campus WLAN

The main objective of this paper is to propose a simple, low cost, reliable and scalable architecture for building Smart Home Systems (SHSs) that can be used to remotely automate and control home appliances, using microcontroller. The proposed architecture aims to take advantage of emerging technologies to make it easier to develop Smart Home systems and to provide more management by expanding its capabilities suitably. The suggested design intends to make it easier and more convenient for many applications to access context data, as well as providing a new schematic guide for creating as complete and comprehensive Smart Home Systems and data processing as possible. Related topics like smart homes and their intelligent systems will be addressed by examining prior work and proposing the authors' opinions in order to suggest the new architecture. The proposed advanced architecture's building blocks include Classic Smart Homes, Internet of Things (IoT), Context-awareness (CA), Cloud Computing (CC), and Rule-based Event Processing Systems (RbEPS). Finally, the proposed architecture is validated and evaluated by constructing a smart home system.