An Experimental Study Towards Attacker Identification in Automotive Networks

<div class="section abstract"><div class="htmlview paragraph">The amount of data communicated in automotive networks is increasing rapidly, leading to more complex systems alongside the rising number of Electronic Control Units (ECUs) in modern vehicles. As the number of ECUs has risen, Controller Area Network (CAN) communication bandwidth has been pushed to its limit. Existing solutions - such as using multiple CAN buses, sending multiple CAN frames or switching to another protocol - require a significant system-design effort and replacement of hardware and software. This has paved the way for CAN Flexible Data-rate (CAN FD), which extends the CAN standard and permits significantly higher data rates, enabling faster firmware upgrades. However, some changes must be made like: exchange the classical CAN microcontroller with a CAN FD microcontroller and also a CAN FD transceiver must be used.</div><div class="htmlview paragraph">This article will explore the benefits of CAN FD, how it compares with the classical CAN protocol, requirements for systems and how to introduce CAN FD into existing CAN networks.</div></div>

Modern cars are equipped with a wide variety of sensors generating continually growing amounts of data. This data is transmitted via bus systems such as Controller Area Network (CAN) inside of the vehicle to the microcontroller-based Electronic Control Units. By connecting the vehicle to its surroundings using wireless interfaces, this data becomes accessible to the vehicle manufacturer from a distance. Through the opening to the outside, cyber attacks can exploit these interfaces and introduce major risks to the privacy and safety of vehicle users. Hence, suitable methods for vehicle security monitoring such as intrusion detection and logging are needed. In this work, we focus on the logging of network data, since this data is useful for the development of security updates, countermeasures and incident signatures. On this account, we propose a new method to aggregate the data of the CAN bus. The method combines CAN frames into so-called flows. Each flow contains a set of packets that share a certain common attribute (e.g.: frame type and identifier). To integrate security monitoring of vehicle fleets seamlessly into backend server systems, the gathered CAN flow data is stored in an industry standard data format. Additionally, the payload data is included in the flow format using a compression algorithm to leverage deep-packet inspection. The evaluation results with realworld vehicle data indicate that in our case about 40 % reduction of the overall data size is possible with our method compared to industry-standard formats for storing CAN frames. On this account, we propose a new method to aggregate the data of the CAN bus. The method combines CAN frames into so-called flows. Each flow contains a set of packets that share a certain common attribute (e.g.: frame type and identifier). To integrate security monitoring of vehicle fleets seamlessly into backend server systems, the gathered CAN flow data is stored in an industry standard data format. Additionally, the payload data is included in the flow format using a compression algorithm to leverage deep-packet inspection. The evaluation results with realworld vehicle data indicate that in our case about 40 % reduction of the overall data size is possible with our method compared to industry-standard formats for storing CAN frames.

The modern car is increasingly connected. That connection is magnified by the presence of a large number of electronic control units (ECUs). The communication between the ECUs of a modern car is assured by the Controller Area Network (CAN) bus system. Despite its importance, the CAN bus system is bereft of security mechanisms making it vulnerable to numerous security attacks. When an attacker succeeds in compromising the ECUs, they can take control and stop the engine, disable the brakes, turn the lights on/off, etc. An intrusion detection system (IDS) can be deployed as an appropriate security measure to detect the malicious network traffic in the CAN bus system. In this paper, we propose a Convolutional Neural Network (CNN)-based network attacks IDS for protecting the CAN bus system. For efficiency reasons, we generated our own datasets from three car models. Our experiment results demonstrate that our classifier is efficient for detecting the CAN bus system attacks, and it performs with a high accuracy of 99.99% and a detection rate of 0.99.

The Controller Area Network (CAN) bus system works inside connected cars as a central system for communication between electronic control units (ECUs). Despite its central importance, the CAN does not support an authentication mechanism, i.e., CAN messages are broadcast without basic security features. As a result, it is easy for attackers to launch attacks at the CAN bus network system. Attackers can compromise the CAN bus system in several ways: denial of service, fuzzing, spoofing, etc. It is imperative to devise methodologies to protect modern cars against the aforementioned attacks. In this paper, we propose a Long Short-Term Memory (LSTM)-based Intrusion Detection System (IDS) to detect and mitigate the CAN bus network attacks. We first inject attacks at the CAN bus system in a car that we have at our disposal to generate the attack dataset, which we use to test and train our model. Our results demonstrate that our classifier is efficient in detecting the CAN attacks. We achieved a detection accuracy of 99.9949%.

The response time distributions of the frames sent on a Controller Area Network (CAN) bus are of prime interest to dimension and validate automotive electronic architectures. However, the existing work on the timing behaviour of the CAN network does not take into account that all the data exchanges between the Electronic Control Units (ECUs) are driven by different and independent clocks which are subject to clock drifts. This paper proposes a model for clock drifts and describes their impact on the CAN frame response time distributions. By implementing the clock drifts in a CAN simulation tool, we show experimentally that the response time distributions converge, for drift values chosen randomly within the same range on all ECUs, whatever the initial phasings between the sending nodes. Furthermore, we show that, as a result of the clock drifts, the situations leading to the worst case response times are transient.

Controller Area Network (CAN) is a bus standard commonly used in the automotive industry. A large number of researches have been carried out on the identity authentication and intrusion detection technology of the in-vehicle network for attacks. This paper presents a method to extract the voltage of CAN bus terminal to obtain the equipment fingerprint. The method identifies different ECUs by measuring the voltage difference on the vehicle network, selects features only from the time domain and detects based on a single frame. This paper mainly focuses on the influence of temperature on the fingerprint of CAN bus terminal. By using a high and low temperature test chamber to simulate different temperature environments during vehicle operation, a large number of CAN frames have been collected for fingerprint extraction. By studying the relationship between temperature and CAN bus terminal fingerprint, the influence of temperature on fingerprint has been compensated. After temperature linear compensation, the recognition rate of voltage-based CAN bus terminal fingerprint extraction increases from 71.2% to 87.6% at 0–80 °C.

With the rapid development of autonomous vehicles (AVs), vehicle safety has attracted attention. Controller area network (CAN) bus without authentication and encryption mechanisms is a weakness of the in-vehicle network (IVN), and attackers always primarily target the CAN bus. Attacks on the AVs' CAN bus are more frequent because AVs have more external interfaces and sensors than ordinary vehicles. To address the abovementioned issues, this paper proposes a lightweight encryption and authentication scheme for the CAN bus of AVs using message authentication codes and Grain stream cipher. The scheme realizes efficient authentication between electronic control units and a counter re-synchronization protocol is used to ensure that authentication failure owing to counter inconsistency is prevented. Blom key management scheme is employed to rapidly distribute and update session keys, avoiding the complicated process of updating pairwise keys. In addition, considering the scalability of the IVN, a key distribution protocol for new nodes was provided. The security proof using Burrows-Abadi-Needham logic and security analysis prove that the proposed scheme can satisfy the security requirements of the IVN. In addition, performance analysis shows that the proposed scheme can meet real-time requirements and has little impact on the busload.

There have been several public demonstrations of attacks on connected vehicles showing the ability of an attacker to take control of a targeted vehicle by injecting messages into their Controller Area Network (CAN) bus. In this article, using injected speed reading and Revolutions Per Minute (RPM) reading messages in in-motion vehicle, we examine the ability of the Pearson correlation and the unsupervised learning methods k-means clustering and Hidden Markov Model (HMM) to differentiate ’no-attack’ and ’under-attack’ states of the given vehicle. We found that the Pearson correlation distinguishes the two states, the k-means clustering method has an acceptable accuracy but high false positive rate and HMM detects attacks with acceptable detection rate but has a high false positive in detecting attacks from speed readings when there is no attack. The accuracy of these unsupervised learning methods are comparable to the ones of the supervised learning methods used by CAN bus Intrusion Detection System (IDS) suppliers. In addition, the article shows that studying CAN anomaly detection techniques using off-vehicle test facilities may not properly evaluate the performance of the detection techniques. The results suggest using other features besides the data content of the CAN messages and integrate knowledge about how the Electronic Control Units (ECUs) collaborate in building effective techniques for the detection of injection of fabricated message attacks.

This system is designed to test automotive CAN (Controller Area Network) controlled devices or entire network. This system not only can display CAN frames (CAN 2.0A/B) received from or sent onto CAN bus, but also can record data on log files for off-line evaluation. Users can configure several monitoring modes and CAN channel features of the system with PC application. Furthermore the USB technology adopted in the system make it a more practical and convenient CAN bus testing system.

An in-vehicle controller area network (CAN) bus is vulnerable because of increased sharing among modern autonomous vehicles and the weak protocol design principle. Spoofing attacks on a CAN bus can be difficult to detect and have the potential to enable devastating attacks. To effectively identify spoofing attacks, we propose the authentication of sender identities using a recurrent neural network with long short-term memory units (RNN-LSTM) based on the features of a fingerprint signal. We also present a way to generate the analog fingerprint signals of electronic control units (ECUs) to train the proposed RNN-LSTM classifier. The proposed RNN-LSTM model is accelerated on embedded Field-Programmable Gate Arrays (FPGA) to allow for real-time detection despite high computational complexity. A comparison of experimental results with the latest studies demonstrates the capability of the proposed RNN-LSTM model and its potential as a solution to in-vehicle CAN bus security.

Controller Area Network (CAN) is an effective choice for the automotive industries due to its simplicity, low cost nature, decrease of wiring density and in addition to that it provide connectivity with multiple nodes with single wiring pair. This paper aims in describing an ARM 7 LPC 2129 based Temperature measurement system with Controller Area Network (CAN) bus. Objective of this paper is to construct a hardware proposal for communication between nodes with CAN bus. A Node to Node communication link has been established which are connected via CAN bus so as to observe and control the temperature values transferring on the CAN bus and send the command signals onto the another node. The hardware boards are designed to be capable of supporting high speed bit rate up to 1Mbps. The CAN communication module can transmit or receive data following CAN Protocol. With the help of the software used, the CAN-BUS communication would be clear to the nodes of the ARM 7 Controllers in the system. The software part is done in KEIL microvision-4 using Embedded -C.

Modern vehicles have significantly increased the number of Internet of Things (IoT) devices called electronic control units (ECUs) connected by in-vehicle networks to provide enhanced features and safety. These devices communicate with the environment and have brought the notion of the Internet of vehicles. The controller area network (CAN) bus facilitates efficient ECU communications and is the standard protocol used by every vehicle, but it is susceptible to remote attacks. Consequently, it is desirable to monitor the CAN bus for malicious activities, such as data injection attacks, that can compromise the vehicular operations. We present an anomaly detection technique that uses an extreme gradient boosting machine (GBM) learning algorithm to categorize unexpected occurrences in the CAN data payload. We further combine GBM with a ten-fold cross-validation method to improve prediction performance. Moreover, we use the early -stopping and grid search approaches to overcome overfitting without affecting model accuracy. We evaluate our detection approach on real CAN bus datasets collected from Hyundai Sonata, a KIA Soul, and Chevrolet Spark with different attack scenarios, such as Denial-of-Service (DoS), fuzzy, spoofing, and malfunction attacks. Using standard metrics, such as accuracy, recall, precision, F1 score, and false-positive rate, the performance analysis of the proposed model achieved an overall accuracy of over 99 percent.

The Partial controller area network (CAN), which can partially turn on and off the operation of electronic control unit (ECU), is a low-power technology and can reduce the CO2 emissions and power consumption of an automobile compared with the existing automobile CAN. However, a problem arises in the application of the Partial CAN whereby the existing automobile CAN databases that contain all the CAN frames of the automobile have many period frames. The periodic frame wakes the ECU every constant cycle, so the power consumption and CO2 emissions savings of ECU are ineffective. To solve this problem, we proposed a new algorithm for applying the Partial CAN that can evade the period wake-up of the ECU. In this paper, we introduce a new algorithm for applying the Partial CAN and analyze the performance of the proposed algorithm by comparing with the existing algorithm.

Rec-CNN: In-vehicle networks intrusion detection using convolutional neural networks trained on recurrence plots

This paper introduces the principle of controller area network (CAN) bus and the structure of fuel cell vehicle control system based on CAN bus. It focuses on electrical air -condition control system for fuel cell vehicle based on CAN bus, which consists of an air condition control node and an air condition compressor drive. The design of electrical air condition control system based on CAN bus is analyzed in detail, including hardware design and software design. The hardware design mainly includes a general-purpose microcontroller P89C51Rx2, a dedicated microcontroller ST72141 for brushless DC Motor and an independent CAN controller etc.. The running result of air-condition control system proves the flexibility and efficiency and reliability of the system design.