Analysis of large-displacement compliant mechanisms using an incremental linearization approach

An intensive study on the dynamic modeling and analysis of compliant mechanisms is presented in this paper based on the pseudo-rigid-body model. The pseudo-rigid-body dynamic model with single degree-of-freedom is proposed at first and the dynamic equation of the 1R pseudo-rigid-body dynamic model for a flexural beam is presented briefly. The pseudo-rigid-body dynamic models with multi-degrees-of-freedom are then derived in detail. The dynamic equations of the 2R pseudo-rigid-body dynamic model and 3R pseudo-rigid-body dynamic model for the flexural beams are obtained using Lagrange equation. Numerical investigations on the natural frequencies and dynamic responses of the three pseudo-rigid-body dynamic models are made. The effectiveness and superiority of the pseudo-rigid-body dynamic model has been shown by comparing with the finite element analysis method. An example of a compliant parallel-guiding mechanism is presented to investigate the dynamic behavior of the mechanism using the 2R pseudo-rigid-body dynamic model.

A parameter optimization framework for determining the pseudo-rigid-body model of cantilever-beams

This study develops a new multi-objective optimization design for a compliant planar spring that is used for upper limb assistive device for disabled people. The structure of spring is designed by arranging the leaf springs in a zigzag shape to permit a large deformation. The spring is a key element of the gravity-balanced mechanism (GBM) in the upper limb assistive device, exoskeleton and upper limb assistive robot. Static equilibration of the GBM is utilized to eliminate the working effort of the disable forearm. The spring is therefore used to adjust the stiffness and to maintain the equilibrium condition. To improve static performances, an effective hybrid approach of the response surface method, finite element method, and multi-objective genetic algorithm is developed. In comparison with common types of surrogates, the Kriging metamodel was found as a prefer black-box to approximate the objective functions. Subsequently, the multi-objective genetic algorithm is adopted to find out the Pareto-optimal set for the spring. The sensitivity of each design variables is then analyzed, and their significant contributions are conducted using the analysis of variance. The predicted results give a good agreement with the validation ones. It eliminates the modeling errors of the analytical method for synthesis and analysis of compliant mechanisms. The results facilitate an optimization design for the intelligent robotics systems for the assistive devices.

Design of a variable-diameter wheel with a novel distributed compliant mechanism

Compliant mechanisms gain at least some of their mobility from the deflection of flexible members rather than from movable joints only. Dynamic effects are very important to improving the design of compliant mechanisms. An investigation on the dynamics and synthesis of the compliant mechanisms is presented. The dynamic model of compliant mechanisms is developed at first. The natural frequency and sensitivity are then studied based on the dynamic model. Finally, optimal design of compliant mechanism is investigated. The experimental study of natural frequency is performed. The comparison between the experiment results and the theoretical results verifies the validity of the experiment system and theoretical model.

Compliant mechanisms are single-piece flexible structures that deliver the desired motion by undergoing elastic deformation as opposed to jointed rigid body motions of conventional mechanisms. Compliance in design leads to jointless, no-assembly (Fig. 1), monolithic mechanical devices and is particularly suited for applications with small range of motions. The compliant windshield wiper shown in Fig. 1 illustrates this paradigm of no-assembly. Conventional flexural mechanisms employ flexural joints that connect relatively rigid links as depicted in Fig. 2. Reduced fatigue life, high stress concentration and difficulty in fabrication are some of the drawbacks of flexural joints. Our focus is on designing compliant mechanisms with distributed compliance which employs flexural links (see Fig. 3) and have no joints (neither pin nor flexural joints) for improved reliability, performance, and ease of manufacture. Distributed compliant mechanisms derive their flexibility due to topology and shape of the material continuum rather than concentrated flexion at few regions. This paper focuses on the unique methodology employed to design jointless mechanisms with distributed compliance. The paper also illustrates a compliant stroke amplification mechanism that was recently designed, fabricated and tested for MEMS application.

Compliant mechanisms, unlike rigid-body mechanisms, are devices that derive some or all of their mobility due to the deformation of their flexible members. The knowledge of existing rigid-body mechanism synthesis techniques is very useful in designing compliant mechanisms. In rigid-body mechanisms, a four-bar is treated as the basic mechanism that can transfer motion, force or energy. In this paper, a compliant single-strip continuum is introduced as the basic compliant mechanism that can transfer motion, force or energy. A classification of compliant mechanisms is presented herein. A methodology for compliant single-strip mechanism synthesis for energy, force or torque specifications is developed in this research as our second objective. The synthesis types, the governing equations, and the variables involved are enumerated.

Compliant mechanisms have been defined as mechanical systems that derive some or all of their mobility from the flexibility of one or more of their members. In general, due to the large-deflection nature of the compliant members, analysis and synthesis of compliant mechanisms have typically required a numerical iterative solution method. Recently, analytical loop-closure synthesis techniques have been extended to the design of compliant mechanisms, by utilizing the concept of an equivalent pseudo-rigid-body model for a compliant mechanism. These developments have greatly simplified the synthesis of compliant mechanisms. These mechanisms have been synthesized for three precision points using analytical and graphical methods. In rigid-link mechanism design, additional precision points may be incorporated by using Burmester theory. With this enhancement as the motivation, this paper presents the first use of Burmester theory to design compliant mechanisms for four and five precision points. This is facilitated by use of the concept of an equivalent pseudo-rigid-body model. Burmester theory yields a linear set of kinematic equations, allowing for their easy utilization herein. Also for some design problems, this theory can provide a graphical representation of all possible solutions for compliant mechanisms. In addition to the specification of precision points for compliant mechanisms, input torque and/or potential energy values may also be prescribed.

Effects of joint clearance on the dynamics of a partly compliant mechanism: Numerical and experimental studies

Dynamic analysis of the precision compliant mechanisms considering thermal effect

The design of compliant mechanisms has been aided by the development of pseudo-rigid-body models to predict the motion of flexible members undergoing large displacements. Many of these models are based on the fact that the end of a cantilever beam follows a near-circular path when planar loads are applied. This paper shows that the application of 3-dimensional end-loading causes a beam to follow a near-spherical path, even for beams with non-circular cross-sections. A 3D pseudo-rigid-body model is presented that allows the motion of an end-loaded rectangular beam to be predicted using a rigid link and a spherical joint. Two sets of deflection limits for 0.5% error are presented and shown to be dependent upon the aspect ratio of the cross-section of the beam. The model has the potential for aiding in the design of spatial compliant mechanisms and analysis of planar compliant mechanisms undergoing large out-of-plane motions.

Bistable mechanical devices remain stable in two distinct positions without power input. They find application in valves, switches, closures, and clasps. Mechanically bistable behavior results from the storage and release of energy, typically in springs, with stable positions occurring at local minima of stored energy. Compliant mechanisms offer an elegant way to achieve this behavior by incorporating both motion and energy storage into the same flexible element. Interest in compliant bistable mechanisms has also recently increased because of the advantages of bistable behavior in many micro-electro-mechanical systems (MEMS). Design of compliant or rigid-body bistable mechanisms typically requires simultaneous consideration of both energy storage and motion requirements. This paper simplifies this process by developing theory that provides prior knowledge of mechanism configurations that guarantee bistable behavior. Configurations which include one or more translational, or slider, joints are studied in this work. Several different mechanism types are analyzed to determine compliant segment placement that will ensure bistable mechanism operation. Examples demonstrate the power of the theory in design.

This paper proposes a new compliant mechanism for the stroke amplification of piezoelectric actuators. Compared with the existing ones, this compliant stroke amplification mechanism (CSAM) has several advantages including lightweight, less stress concentration, large motion range, as well as ease of manufacture in macro- and micro-scales, mainly due to the completely distributed compliance and largely reduced moving mass. Kinetostatic models of the CSAM, with consideration of the payloads applied on the output stage, are derived for quick and insightful determinate analysis, which enables optimization of the associated parameters to achieve different objectives. The results obtained from the kinetostatic models are in reasonable agreement with the FEA simulation results, with less than 3.8% difference when the input displacement is less than 10 µm. An optimization method, based on the analytical models, is introduced and employed to increase the amplification ratio of the CSAM by up to 240%. The optimized CSAM is an excellent candidate for the stroke amplification of piezoelectric actuators, which is fabricated and experimentally tested. The optimization method is able to be extended to design other compliant mechanisms with optimized size, shape and topology configuration simultaneously.

Compliant mechanisms use the flexibility of the limbs for movement and are produced monolithic, without any conventional joint. These flexible mechanisms have wide applications in several fields such as sensors, grippers, parallel mechanisms, micro-electro-mechanical systems, high-precision devices, and biomedical and surgery robots. Topology optimization is regarded as one of the most frequently used approaches for designing compliant mechanisms. The present study aimed to develop the ground structure approach by meshing the design domain using curved beam elements. Moreover, it seeks to implement three different metaheuristic algorithms, including the genetic algorithm, the imperialist competition algorithm, and the equilibrium optimizer for the topology optimization problem. The structural analysis of the compliant mechanism is necessary for determining the values of the objective functions for the optimization process. In the present study, the finite element method was used to analyze the obtained compliant mechanism. Based on the results, an optimum compliant mechanism with both straight and curved beam elements had better performance compared with a compliant mechanism with only straight beams.

Compliant mechanisms utilize the elastic deformation of their constituent members to transfer forces or displacements. Compliant mechanisms are advantageous in robotic applications because of their simplified manufacturing, monolithic structure, high precision, low wear and backlash, and flexibility to accommodate a wide range of actuation schemes. Despite these significant advantages, modeling these mechanisms is challenging because of their complex and large nonlinear deformations. Currently, most modeling methods for compliant mechanisms are either kinematic or kinetostatic, such as the pseudo-rigid body method (PRBM), beam constraint model (BCM), and load-flow-based method. These methods are mostly limited to bending deformation and do not consider shear or stretch strain. Furthermore, they are not conducive to modeling compliant mechanisms with embedded actuators in the geometry of the mechanism. To overcome these limitations, here we adopt Cosserat rod modeling, which captures the generalized deformations of the constituent members of compliant mechanisms. Furthermore, it allows the modeling of compliant mechanisms with actuation members. Several compliant mechanism experimental prototypes, including compliant inverters and a compliant gripper, were presented to validate and depict the effectiveness of the Cosserat rod modeling. This modeling approach enables large-scale and efficient modeling of the complaint mechanisms with actuators and sensors.