Analytical determination of back-side contact gear mesh stiffness

A study of effects of tooth surface wear on time-varying mesh stiffness of external spur gear considering wear evolution process

In order to accurately describe the complex transmission systems and clarify the effects of internal and external excitation on the vibration characteristics for large complex transmission systems, a dynamics model considering gear meshing error and time-varying meshing stiffness is established at two-stage planetary gears systems. The coupling model is established by matrix set method for two-stage planetary gears and multistage spur gears transmission systems. The random load excitation verified by experiments is the external excitation in the system, and the excitation caused by the time-varying meshing stiffness and meshing error is the internal excitation. The research on the response of the vibration systems shows that the internal excitation caused by gear meshing stiffness and gear meshing error has important influence on the dynamic load behavior of spur gears transmission in complex systems. For the planetary system with heavy external load, the dynamic behavior mainly depends on the external load, and the influence of internal excitation on the dynamic meshing force is less than that of the external excitation for the planetary system. The external excitation mainly affects the low-frequency region of the dynamic meshing force for the system, and the internal excitation affects the high-frequency region of the dynamic force for the system. The frequency influence interval of the internal excitation is much larger than that of the external excitation.

Effect of Back-side Contact on Mesh Stiffness of Spur Gear Pair by Finite Element Method

An expert system for fatigue testing of airframes: Gubarev, V.V., Grif, M.G., Metyolkin, N.G., Seryoznov, A.N. and Sklyarov, A.A. Conf. Fatigue and Fracture in Steel and Concrete Structures, ISFF '91, Madras, India, Dec 1991 Vol 2 (Oxford & IBH Publishing Co. Pvt. Ltd, New Delhi, India, 1991) 923–927

An improved analytical model for gear mesh stiffness calculation

Three new models for evaluation of standard involute spur gear mesh stiffness

Simulation of crack propagation in spur gear tooth for different gear parameter and its influence on mesh stiffness

On gear time-varying meshing stiffness calculation considering indexing feeds and processing characteristics of gear shaping processing

A probability distribution model of tooth pits for evaluating time-varying mesh stiffness of pitting gears

Time-varying mesh stiffness (TVMS) is a vital internal excitation source for the spiral bevel gear (SBG) transmission system. Spalling defect often causes decrease in gear mesh stiffness and changes the dynamic characteristics of the gear system, which further increases noise and vibration. This paper aims to calculate the TVMS and establish dynamic model of SBG with spalling defect. In this study, a novel analytical model based on slice method is proposed to calculate the TVMS of SBG considering spalling defect. Subsequently, the influence of spalling defect on the TVMS is studied through a numerical simulation, and the proposed analytical model is verified by a finite element model. Besides, an 8-DOF dynamic model is established for SBG transmission system. Incorporating the spalling defect into TVMS, the dynamic responses of spalled SBG are analysed. The numerical results indicate that spalling defect would cause periodic impact in time domain. Finally, an experiment is designed to verify the proposed dynamic model. The experimental results show that the spalling defect makes the response characterized by periodic impact with the rotating frequency of spalled pinion. Conflict of Interest Statement The authors declare no conflicts of interest.

Time-varying mesh stiffness (TVMS) of gear plays vital role in analysing dynamic characteristic of gear transmission. So accurately evaluating the TVMS is important and essential. In this paper, a revised method to calculate the TVMS of helical gear is proposed. Based on slice method, the helical gear is sliced into pieces along the tooth width direction. The proposed method corrects the fillet foundation stiffness within multi-tooth in contact and considers the non-linearity and load-dependence of the Hertzian contact stiffness. The effect of the axial mesh force is considered. Finally, an equivalent helical gear model is established in ANSYS to study the mesh stiffness. The results show the proposed method has high effectiveness compared with FEM (finite element method).

Crack detection of a modified high contact ratio gear

PurposeThis study aims to research the time-varying mesh stiffness (TVMS) model for orthogonal face gear drives considering elastohydrodynamic lubrication (EHL) and provide a theoretical basis for understanding the dynamic characteristics of face gear drives.Design/methodology/approachConsidering EHL, a novel model is proposed to calculate the TVMS of orthogonal face gears using the deformation compatibility condition. First, the tooth surface equations of orthogonal face gears are derived according to the tooth surface generation principle. Then, the oil film thickness on the tooth surface of face gears is obtained by solving the governing equations of EHL. Furthermore, the proposed model is used to calculate the TVMS of face gears along the mesh cycle and is verified. Finally, the effects of module, tooth number of shaper cutter and pressure angle on mesh stiffness are analyzed.FindingsThe results indicate that when the contact ratio is greater than 1 and less than or equal to 2, the TVMS of face gears exhibits a phenomenon of double-single tooth alternating meshing where sudden changes occur. As the module increases, the overall mesh stiffness of face gears increases, and the magnitude of the sudden change at the moment of single-double tooth alternating meshing gradually increases. As the tooth number of shaper cutter and pressure angle increase, so does the TVMS of face gears. When the effect of oil film is considered, the calculated TVMS of face gears slightly increases overall and the increase in average oil film thickness leads to a rise in the TVMS. This study provides a theoretical basis for understanding the dynamic characteristics of face gear drives.Originality/valueThis study’s originality and value lie in its comprehensive approach, which includes conducting analysis based on loaded tooth contact, considering the influence of elastohydrodynamic lubrication, proposing a novel analytical–finite–element model, calculating TVMS of face gears, verifying the proposed model and analyzing the effects of typical structural parameters and oil film thickness.

Effects of tooth profile modification on dynamic responses of a high speed gear-rotor-bearing system

<div class="section abstract"><div class="htmlview paragraph">A new capability to analyze the dynamic interaction of nonlinear hypoid gear mesh characteristics and time-varying bearing stiffness is proposed. Both backlash nonlinearity and time-varying mesh parameters, such as mesh stiffness, mesh point and line-of-action, are included in the nonlinear hypoid gear mesh model. The time-varying bearing stiffness behavior due to the changing orbital position of rolling elements is also modeled. A practical application is studied to reveal the dynamic characteristics of the complex interactions. Dynamic simulation results show that dynamic mesh force is relatively insensitive to the temporal variation in the bearing stiffness. On the other hand, the dynamic bearing loads are affected significantly by the time-varying bearing stiffness, especially in the case of heavy drive torque load without the occurrence of jump response phenomenon. However, for the case of light load condition assuming time-invariant mesh parameters, the dynamic bearing loads are insensitive to time-varying bearing stiffness. The analysis also reveals that the presence of appropriate backlash nonlinearity can stabilize the parametric resonance caused by the time-varying bearing stiffness for the case of light load condition assuming the mesh parameters are time-invariant.</div></div>