Artificial neural network maximum power point tracking for mitigation photovoltaic harmonic distortion

The escalating demands and increasing awareness for the environment, resulted in deployment of Photovoltaic (PV) system as a viable option. PV system are widely installed for numerous applications. However, the challenges in tracking the maximum power with intermittent atmospheric condition and varying load is significant. Maximum Power Point Tracking (MPPT) algorithms are employed and based on their convergence speed, control of external variations and oscillation, the output power efficiency, and other significant factors viz. the algorithm complexity and implementation cost, novel MPPT approach are preferable than the conventional approach. This paper presents an artificial intelligence-based optimization controller for MPPT in a PV system under varying load and irradiance conditions. Comparative analysis of Artificial Neural Network (ANN) and Particle Swarm Optimization (PSO) based MPPT is simulated and analysed. The PV system consisting of PV array and boost converter with MPPT controller feeds the DC load. The power conversion and panel efficiency are the significant factors to determine the effectiveness of tracking maximum power point. The simulation results show the performance of these controllers on the PV panel output power and the load side output power under changing loads and irradiance. In addition, the comparison of PV panel efficiency of ANN and PSO based MPPT techniques w.r.t changing loads is carried out. Based on the above analysis, PSO based MPPT algorithm marginally outperforms the ANN based MPPT algorithm. Further, the implementation of hybrid MPPT (ANN &PSO) for higher accuracy and tracking capability can be carried out as future work.

In renewable system control engineering, Maximum Power Point Tracking (MPPT) techniques are considered as one of the key steps in photovoltaic (PV) system development. Indeed, some MPPT techniques provide high performance under uniform irradiation and temperature conditions. However, their performance significantly degrades when the two preceding climatic conditions suddenly change. Therefore, this paper proposes a new voltage regulation based on Fuzzy Logic Control (FLC) strategy and small-signal model of DC–DC booster converter. The proposed control scheme is mainly based on the indirect incremental conductance (Inc) technique, equipped with an optimal integrator controller (OIC). It is implemented in a PV system, consisting of a DC–DC boost converter connected to a resistive load, with the main objective of ensuring a good MPP tracking behavior for variable operating conditions. To achieve this objective, the proposed MPPT strategy is designed around two stages. First, the smooth reference voltage is ensured by a Single-Input Single-Output (SISO) fuzzy logic controller using the Inc technique based on the MPPT approach. Then, the optimal integrator controller stabilizing the closed-loop system is integrated with optimization of its parameter according to Routh’s criterion for resistive load variations. Simulation results confirm the effectiveness of the proposed MPPT technique compared to some commonly used MPPT approaches. The superiority of the proposal is proven by using efficiency ratio, which rises more than 98% in all case studies. These objectives are ensured for both uniform and critical sudden change in weather conditions, regardless of resistive load variations.

This paper presents a control for a three-phase an eleven-level cascaded H-bridge inverter for photovoltaic (PV) system. The maximum power point tracking (MPPT) is capable of extracting maximum power from the PV array connected to each DC link voltage level. The MPPT algorithm is solved by fuzzy logic controller. Space vector pulse width modulation (SVPWM) algorithm uses a simple mapping to generate gate signals for the inverter. This is done to achieve high dynamic performance with low total harmonic distortion (THD). The validity of the system is verified through MATLAB/Simulink and results are compared with three-phase three-level, five-level, seven-level and nine-level cascaded H-bridge inverter for PV system in terms of THD. Finally, simulation results are presented to verify the effectiveness and accuracy of the proposed system.

The proposed work deals with the implementation of a control approach for an active power transfer between solar photovoltaic (PV) array and grid/ load alongwith power quality improvement by eliminating harmonics and compensating reactive power required by the load in the distribution system. The PV array is directly connected across the DC link of a voltage source converter (VSC). The power is transferred to the grid/ load through VSC, which performs the function of distribution static compensator (DSTATCOM) by injecting compensating currents in the proposed system. The PV array is operated at maximum power by employing the usage of perturb and observe (P&O) maximum power point tracking (MPPT) approach in order to extract the available maximum power from the solar PV array. A feed-forward term for the solar PV array power, is incorporated for the enhancement of dynamic response. The prominence of the control algorithm lies in the efficient switching of VSC, by generating reference grid currents, which are obtained through indirect current control technique. The recursive digital filter is utilized for processing the load currents and extracting the active power component of the load currents. Therefore, the active power component of load currents obtained, are used for generating the reference grid currents in the proposed system. A prototype of the system is developed in the laboratory and its performance is studied for varying loads, changing solar insolation, and voltage swell and voltage sag conditions.

The current publication is directed to achieve a high-performance stand-alone PV system having the capability of tracking maximum output power, providing fixed output DC voltage, and attaining efficient system utilization, under different irradiation levels. A new maximum power point tracking (MPPT) approach integrating the incremental conductance algorithm and fuzzy logic control, and enhanced with PI-controller, was proposed to track maximum power. To provide fixed output DC voltage and approaching full system utilization, the PV system is equipped with a battery bank, electrolyzer; as a dump load, and buck-boost converter, with two controllers. The results of the proposed MPPT technique; modified incremental conductance (MINC), are compared with the corresponding results of three prevalently implemented MPPT algorithms: perturbed and observed (P&O), modified variable step-size P&O (VSZ-PO) and the ordinarily incremental conductance (INC). The highest output power, best tracking efficiency and best output power response are achieved by utilizing the proposed MPPT method. The results of the output voltage response and electrolizer on/off states confirm the ability of the PV scheme to provide fixed DC voltage and attain efficient system utilization, under varying irradiances.

Solar photovoltaic (PV) system contributes a significant role in meeting power requirements and helps the decentralization of power generation and distribution. The output of the individual photovoltaic module depends on local temperature and irradiance. Since the variation of these parameters depends on the environmental factors, it is difficult to obtain maximum power in all instances. The maximum power point tracking (MPPT) technique is used for tracking the maximum power available at a particular instant. This paper presents the maximum power extraction from a photovoltaic system using Artificial Intelligence (AI) techniques. AI based methods provide a fast dynamic response with high accuracy and mitigate the effects of partial shading. A comparative study is performed for various AI based MPPT techniques such as Fuzzy, Artificial Neural Network (ANN), and Adaptive Neuro Fuzzy Inference System (ANFIS). PV module output is interfaced with the resistive load through the Z-Source inverter (ZSI). The ZSI boost the input voltage and provides an AC output voltage. The AI based MPPT techniques have been investigated with conventional Z-source Inverter (ZSI) and Switched Inductor Z-Source inverter (SL-ZSI). A simple boost control technique is employed to control, both conventional and SL Z-source inverter. The performance of the system is verified using MATLAB Simulink.

Energy crises and the growth of the energy demand have increased the interest in utilizing unconventional power sources. Thus, renewable energy sources have become a topic of interest to mitigate rising energy concerns and cope with increased electricity demand. With remarkable merits including cleanness and abundance, photovoltaic (PV) solar energy systems are a key to solving these issues. The employed inverters should effectively utilize the maximum available power from the PV solar system and transfer this power to the utility grid without posing any further limitations. However, the unequal power generation of different PV systems caused by partial shading (PS) and other PV panel degradation factors leads to a reduction in generation capacity. One of the relatively new solutions to mitigate the mismatch concerns between the PV modules and sub-modules is to extract the maximum power of each sub-module individually. The main objective of this paper is to present a comprehensive review of such PV grid-connected inverters topologies associated with sub-module connection and control. It will classify the PV grid-tied inverters in accordance with the level where the maximum power point tracking (MPPT) system is implemented. A special focus has been placed on sub-module microinverters (MI) in terms of circuit topologies, conversion efficiency, and controller design. This paper provides a comprehensive analysis of employing the distributed MPPT (DMPPT) approach to maximize the power generation of PV systems by mitigating the mismatch issues inside the PV module. The circuit topology, PV system configuration, and MPPT algorithms used for applying DMPPT solutions in PV SMs are discussed in detail in this study.

A hybrid maximum power point tracking for partially shaded photovoltaic systems in the tropics

Due to the Randomness and fluctuation of the photovoltaic (PV) system, Maximum Power Point Tracking (MPPT) algorithm is employed to ensure the maximum power extraction from PV arrays, when it is connected to the grid. The previous studies have indicated that the MPPT algorithm is one of the main causes of interharmonics emission in PV systems. The MPPT algorithm parameters such as perturbation step size inevitably have a strong impact on the interharmonics in the current injected to the grid. In general, a smaller MPPT perturbation step size will reduce the interharmonics emission level, but it will result in poor tracking performance of the MPPT algorithm. Thus, there is a trade-off between the MPPT efficiency and the interharmonics emission in PV system. In this paper, an interharmonics suppression scheme with variable step size MPPT algorithm was proposed. In the suppression scheme, two voltage values near by the MPPT voltage and two tracking step size are preset. When the dc-link voltage of PV is between the two preset voltage values, it means that the PV power near its MPP and the smaller perturbation step size implemented in the MPPT algorithm. Otherwise, the bigger perturbation step size is employed. It can greatly reduce interharmonics emission level and maintain the MPPT efficiency. Simulations have been carried out to verify the effectiveness of the suppression scheme.

Solar energy is the most promising among many renewable energy sources to meet the increasing demand. Photovoltaic (PV) based power generating solutions are expected to gain popularity as a power source for different applications, including independent and grid connected loads, due to their cleanliness, high performance, and high dependability. The efficacy of photovoltaic systems is impacted by several elements, including geographical location, positioning, shadowing effects, and local climate conditions. In order to fulfil the demands of loads, an interleaved boost converter is utilized, which has a reduced number of filters with less stress on the devices. Solar powered systems employ several maximum power point tracking (MPPT) methodologies. However, when there is partial shading, many power peaks arise, which complicates the identification of the overall peak. Although MPPT approaches are designed to measure and maintain the global maximum power point (GMPP), there are still significant oscillations observed around the GMPP with subpar settling time, tracking efficiency, and conversion efficiency. In this work, novel hybrid MPPT technique called artificial neural network supported adaptable stepped-scaled perturb and observe (ANN-ASSPO) method and water cycle optimization based perturb and observe (WCO-PO) have been proposed. Artificial neural network (ANN) has been used to determine the best scaling factor in ANN-ASSPO MPPT. Performance is enhanced in ANN-ASSPO MPPT by using the optimum scaling factor, particularly in situations when the irradiance is rapidly changing/partial shading conditions. Similarly, in WCO-PO MPPT water cycle optimization is used to determine the peak power when the PV panel is subjected to partial shading conditions. The performances of proposed hybrid MPPT ANN-ASSPO and WCO-PO techniques have been compared in terms of power generated, output voltage, average settling time and conversion efficiency. The MATLAB/Simulink tool is employed to carry out the experiment for this study.

Solar and wind are the most prevalent resources due to their accessibility and the simplicity of their conversion into power. Each renewable resource necessitates a DC/DC boost converter with MPPT management for power generation. The maximum power point tracking (MPPT) technology is utilized to achieve optimal efficiency in photovoltaic (PV) and wind energy systems. Perturbation and Observation-MPPT approach is employed in photovoltaic systems where direct current voltage serves as the perturbation variable. In wind energy systems, a perturbation variable in the form of direct current is utilized in the modified perturb and observe maximum power point tracking algorithm. The modified perturb and observe technique exhibits stability and rapid tracking in response to abrupt changes in wind speed. The greatest Power Point Tracking (MPPT) technique employed with a boost converter optimally takes the greatest power from the available source. The simulation of both renewable energy sources is conducted independently in PSIM 9.0 utilizing various MPPT approaches.

This paper proposes a variable DC-link reference voltage algorithm for wide range of maximum power point tracking (MPPT) for two-string photovoltaic (PV) systems. A multi-string system, which is a kind of PV system, is widely used due to its many merits (such as the ability to use low rating devices, high MPPT efficiency, and so forth). PV systems can choose their input voltages on the basis of their PV cell connection structure. The PV cell connection structure can be restricted because the input voltage and current affect the PV system design. This reduces the MPPT range under some weather conditions. In the restricted PV connection structure, this algorithm enlarges the MPPT range and minimizes the increment of the total harmonic distortion (THD) by selecting the appropriate DC-link voltage reference which is changed by comparing the sorted input voltage. To verify the proposed algorithm, simulation and experiments are conducted to show the results of the performance for the proposed algorithm.

This study offers a thorough examination of a photovoltaic (PV) system using a variety of maximum power point tracking (MPPT) methods, including fuzzy logic control (FLC), adaptive neuro-fuzzy inference systems (ANFIS), perturb and observe (P&O), and artificial neural networks (ANN). Optimizing power extraction from PV systems under various environmental circumstances, including temperature variations and irradiance, is the main goal of these MPPT algorithms. Despite its widespread use and affordability, the P&O algorithm may have performance issues in dynamic circumstances. By using fuzzy logic to adjust to non-linear changes in environmental conditions, FLC improves P&O and offers more dependable and seamless operation. Although they demand a large amount of data and processing power, ANN-based MPPT approaches provide sophisticated capabilities by predicting optimal operating points by learning from historical system actions. By fusing fuzzy logic and neural networks, ANFIS offers a reliable solution that can more accurately adjust in real time to changing circumstances. These algorithms' incorporation into a PV system allows for more flexible and effective power management, guaranteeing peak performance in a range of climatic conditions. By combining many MPPT techniques, hybrid approaches can further reduce the drawbacks of individual approaches and improve the overall dependability and efficiency of PV systems.

The paper introduces a novel Maximum Power Point Tracking (MPPT) approach for Photovoltaic (PV) systems which is based on Golden Section Optimization (GSO). The approach finds the Maximum Power Point (MPP) by a method known as interval shrinking. Initially, two points were extracted from the known search space, then evaluated and a new point was generated accordingly. At the given iteration, according to the evaluation observations, the algorithm has a new narrowed interval bounded by the new point and one of the original points. When the interval is short enough, the algorithm begins iterating and the PV is required to run at the average value of the last discovered interval without disrupting either another voltage or the duty cycle. This thing makes the PV system converge easily to the MPP and around the highest Power Point without voltage or power oscillations, thus minimizing energy loss. The study reveals that, under quickly changing conditions and PV modules, the MPPT algorithm uses a few arithmetic operations and monitors the MPP of PV systems rapidly and accurately.

Nowadays, grid-connected photovoltaic (PV) power system is quite popular in many countries. For grid-connected PV power system, to achieve maximum power and good power quality of the system are considered as big challenges. In order to achieve this, artificial intelligent (AI) controller-based maximum power point tracking (MPPT) algorithm has been investigated for PV system as well as a new cascade multilevel inverter (MLI) is proposed for grid integration of PV system. The proposed cascade MLI has been designed with a smaller number of power electronic switches and it can be operated at asynchronous voltage sources, which is most adaptable for PV system. This proposed inverter can reduce the total harmonic distortion (THD) at output side by means of increasing the output voltage level with this power quality of the system has been improved. The microgrid integration of proposed inverter has been controlled by using AI-based voltage source controller and this proposed system is designed and simulated in MATLAB environment at various weather conditions and loading conditions. Finally, prototype model has been developed in laboratory and evaluating its performance. The simulation results and prototype results were verified with IEEE 1547 standard that proves the proposed system effectiveness.