Bayesian Spectral Decomposition for Efficient Modal Identification Using Ambient Vibration

Modal parameter identification is an important content for the research on dynamic behavior of civil engineering structures. For the conventional modal parameter identification techniques, excitation signal and response signal are necessary. But excitations can not be measured for structures under natural loading conditions, or excited by random forces. So, the operational modal parameter identification approaches are developing to identify structural modal parameters by using vibration response signal directly. In this paper, a new method for modal parameter identification depending on ambient excitation response signal is proposed based on independent component analysis (ICA). For modal coordinates independent of each other, ICA can extract modal coordinates of structure and estimate mode shape matrix using vibration response signal directly. The free vibration responses can be obtained by random decrement technique (RDT) from modal coordinates which are random processes, and then the natural frequencies and damping ratios are calculated by Hilbert transform. Numerical simulation results indicate that this method is effective and suitable for output-only structural modal parameter identification.

Performing forced vibration tests on full-scale structures is the most reliable way of determining the relevant modal parameters in structural dynamics, such as modal frequencies, mode shapes, modal damping, and modal masses. This study describes the modal identification of a double-level curved cable-stayed bridge with separate deck systems for pedestrians and vehicles via forced vibration tests. The steady-state structural responses to sinusoidal excitations produced by an electrodynamic shaker are recorded under varying excitation frequencies, and the frequency response functions are established. The measured frequency response functions are curve fitted to estimate the modal parameters. The numerical simulation of frequency response function–based modal parameter identification of an elastically multi-supported continuous beam structure is carried out, and the emphasis has been placed on the evaluation of the effect of an additional shaker mass, excitation frequency step and range, multi-mode vibration, and noise on identification results. Finally, the modal parameters for the first lateral mode of a double-level curved cable-stayed bridge are identified by forced vibration experiments, and the results are compared with those from ambient vibration tests and free vibration tests. The effect of the unmeasured wind excitation on identification is discussed. It is shown that the effect of ambient vibration is minor for wind velocity of 3–5 m/s. The damping ratios identified by forced and free vibration tests are comparable, while those from ambient vibration are subject to large variations. The modal mass obtained from forced vibration tests is in good agreement with finite element prediction, which provides design basis for mass-type dampers.

The instrumented Canton Tower is a 610 m high-rise structure, which has been considered as a benchmark problem for structural health monitoring (SHM) research. In this paper, an improved automatic modal identification method is presented based on a natural excitation technique in conjunction with the eigensystem realization algorithm (NExT/ERA). In the proposed modal identification method, damping ratio, consistent mode indicator from observability matrices (CMI_O) and modal amplitude coherence (MAC) are used as criteria to distinguish the physically true modes from spurious modes. Enhanced frequency domain decomposition (EFDD), the data-driven stochastic subspace identification method (SSI-DATA) and the proposed method are respectively applied to extract the modal parameters of the Canton Tower under different environmental conditions. Results of modal parameter identification based on output-only measurements are presented and discussed. User-selected parameters used in those methods are suggested and discussed. Furthermore, the effect of environmental conditions on the dynamic characteristics of Canton tower is investigated.

An out-put only modal parameter identification method based on variational mode decomposition (VMD) is developed for civil structure identifications. The recently developed VMD technique is utilized to decompose the free decay response (FDR) of a structure into to modal responses. A novel procedure is developed to calculate the instantaneous modal frequencies and instantaneous modal damping ratios. The proposed identification method can straightforwardly extract the mode shape vectors using the modal responses extracted from the FDRs at all available sensors on the structure. A series of numerical and experimental case studies are conducted to demonstrate the efficiency and highlight the superiority of the proposed method in modal parameter identification using both free vibration and ambient vibration data. The results of the present method are compared with those of the empirical mode decomposition-based method, and the superiorities of the present method are verified. The proposed method is proved to be efficient and accurate in modal parameter identification for both linear and nonlinear civil structures, including structures with closely spaced modes, sudden modal parameter variation, and amplitude-dependent modal parameters, etc.

Structural modal parameter identification with the Power-Exponential window function

An accurate prediction for the response of civil and mechanical engineering structures subject to ambient excitation requires the information of dynamic properties of these structures including natural frequencies, damping ratios and mode shapes. Since the excitation force is not available as a measured signal, we need to develop techniques which are capable of accurately extracting the modal parameters from output-only data. This article presents the results of modal parameter identification using two time-domain methods as follows: the autoregressive moving average vector (ARMAV) method and the state–space method. These methods directly work with the recorded time signals and allow the analysis of structures where only the output is measured, while the input is unmeasured and unknown. The equivalence between ARMAV and state–space approaches for the problem of modal parameter identification of vibrating systems is shown in the article. Using only the singular value decomposition of a block Hankel matrix of sample covariances, it is shown that these two approaches give identical modal parameters in the case where the block Hankel matrix has full row rank. The time-domain modal identification algorithms have a serious problem of model order determination: when extracting structural modes these algorithms always generate spurious modes. A modal indicator to differentiate spurious and structural modes is presented. Numerical and experimental examples are given to show the effectiveness of the ARMAV or state–space approaches in modal parameter identification using response data only.

The integrity of offshore structures is prone to the threat of drifting sea ice. By exciting the natural frequencies of the ice–structure interaction system, severe vibrations may occur. For a better understanding of how dynamic ice–structure interaction affects the system properties, a stochastic subspace system identification technique, SSI-cov is introduced to identify modal parameters during dynamic ice–structure interactions. Due to the uncertain input variables of SSI-cov, the identified modal parameters suffer from the quantitative judgment of the analyst. To address this problem, this study proposes an uncertainty analysis (UA) framework to obtain estimates of modal parameters. This framework constitutes both a sensitivity analysis (SA) and a UA. First, SA is applied to pick up the input variables that contribute the most to the identified modal parameters. Next, the important variables are left free to vary over their range of existence to obtain the modal parameters’ uncertainties. The framework is applied to full-scale tests from Norströmsgrund lighthouse and model tests carried out in Hamburg Ship Model Basin (HSVA). The comparison with traditional automated modal parameter identification shows its superiority in terms of the accuracy of modal parameters.

This paper chooses the Nanjing-Hangzhou high speed overbridge, a self-anchored suspension bridge, as the research target, trying to identify the dynamic characteristic parameters of the bridge by using the peak-picking method to analyze the velocity response data under ambient excitation collected by 7 vibration pickup sensors set on the bridge deck. The ABAQUS is used to set up a three-dimensional finite element model for the full bridge and amends the finite element model of the suspension bridge based on the identified modal parameter, and suspender force picked by the PDV100 laser vibrometer. The study shows that the modal parameter can well be identified by analyzing the bridge vibration velocity collected by 7 survey points. The identified modal parameter and measured suspender force can be used as the basis of the amendment of the finite element model of the suspension bridge. The amended model can truthfully reflect the structural physical features and it can also be the benchmark model for the long-term health monitoring and condition assessment of the bridge.

Accurate and timely identification of modal parameters of long-span bridges is important for bridge health monitoring and wind tunnel tests. Wavelet analysis is one of the most advantageous methods for identification because of its good localization characteristics in both time and frequency domain. In recent years, the wavelet method has been applied more frequently in parameter identification of linear and nonlinear systems. In this article, based on wavelet ridges and wavelet skeleton, the improved modal parameter identification method was studied. To find the appropriate time-frequency resolution, an optimal wavelet basis design principle based on minimum Shannon entropy was proposed. Aiming at endpoint effect in wavelet transform, a prediction continuation method based on support vector machine (SVM) was proposed, which can effectively suppress the endpoint effect of the extended samples. In view of the fact that the ridges of metric matrices obtained by the traditional crazy climber algorithm cannot fully reflect the distribution of ridges of modulus value matrices of wavelet coefficients, an improved high-precision crazy climber algorithm was put forward to accurately identify the position of the ridge of wavelet coefficients. Finally, taking a long-span cable-stayed bridge and a long-span suspension bridge as the engineering background, improved continuous wavelet transform (CWT) was applied to modal parameter identification of bridge under ambient excitation. The modal parameters such as modal frequency, damping ratio, and mode shape were obtained. Compared with the calculation value of the numerical simulation of long-span cable-stayed bridge and wind tunnel test of long-span suspension bridge, the reliability of CWT for modal parameter identification of long-span bridges under ambient excitation was verified.

Automated identification and long-term tracking of modal parameters for a super high-rise building

Operational modal analysis of a high-rise multi-function building with dampers by a Bayesian approach

Traditional modal parameter identification methods have many disadvantages, especially when used for processing nonlinear and non-stationary signals. In addition, they are usually not able to accurately identify the damping ratio and damage. In this study, methods based on the Hilbert-Huang transform (HHT) are investigated for structural modal parameter identification and damage diagnosis. First, mirror extension and prediction via a radial basis function (RBF) neural network are used to restrain the troublesome end-effect issue in empirical mode decomposition (EMD), which is a crucial part of HHT. Then, the approaches based on HHT combined with other techniques, such as the random decrement technique (RDT), natural excitation technique (NExT) and stochastic subspace identification (SSI), are proposed to identify modal parameters of structures. Furthermore, a damage diagnosis method based on the HHT is also proposed. Time-varying instantaneous frequency and instantaneous energy are used to identify the damage evolution of the structure. The relative amplitude of the Hilbert marginal spectrum is used to identify the damage location of the structure. Finally, acceleration records at gauge points from shaking table testing of a 12-story reinforced concrete frame model are taken to validate the proposed approaches. The results show that the proposed approaches based on HHT for modal parameter identification and damage diagnosis are reliable and practical.

This paper reports the step-by-step procedures of a full-scale ambient vibration test and the corresponding modal identification and Bayesian structural model updating of a coupled building. The building is characterized as a combination of a main part and a complementary part connected together by corridors in between. Compared with the main part, the volume of the complementary part is much smaller. Therefore, the influence on the dynamic properties of the complementary part from its counterpart is expected. To capture the dynamic properties of the coupled building, a 21-setup ambient vibration test was designed to cover all the degrees of freedom (DOFs) of interest. The modal parameters of each setup were identified following the frequency domain decomposition (FDD) method and the partial mode shapes from different setups were assembled following a least-squares method. To determine the stiffness of the linkage between the two parts, the coupled building was simulated with two linked shear buildings and updated utilizing the Markov chain Monte Carlo (MCMC)-based Bayesian model updating method. The identified modal parameters revealed interesting features about the coupled effects between the main part and complementary part and were discussed in detail. The good match between the model-predicted and identified modal parameters verified the validity of proposed shear building model. This study provides valuable experience in the area of structural model updating and structural health monitoring.

Conventional nuclear data evaluation methods using generalized linear least squares make the following assumptions: prior and posterior probability distribution functions (PDFs) of all model parameters and data are normal (Gaussian); the linear approximation is sufficiently accurate to minimize the cost function (even for nonlinear models); the model (e.g., of neutron cross section) and experimental data (including covariance data) are without defect and prior PDFs of parameters and measured data are known perfectly. Neglect of covariance between model parameters and measured data in conventional evaluations contributes to imperfections. These assumptions are inherent to the generalized linear least squares minimization method commonly used for resolved resonance region neutron cross section evaluations but are often not justified due to the presence of non-normal PDFs, nonlinear models (e.g., R-matrix formalism), and inherent imperfections in data and models (e.g. imperfect covariance data). Here, these assumptions are removed in a mathematical framework of Bayes’ theorem, which is implemented using the Metropolis-Hastings Monte Carlo method. Most importantly, new parameters are introduced to parameterize discrepancies between the theoretical model and measured data to quantify judgement about discrepancies or imperfections in a reproducible manner. An evaluation of 233U in the eV region using the ENDF-B/VIII.0 library and transmission data (Guber et al.) is presented, and posterior parameters are compared to those obtained by conventional evaluation methods. This example illustrates the effects of removing the most harmful assumption: that of model-data perfection.

Modal analysis, which provides modal parameters including frequencies, damping ratios, and mode shapes, is essential for assessing structural safety in structural health monitoring. Automated operational modal analysis (AOMA) offers a promising alternative to traditional methods that depend heavily on human intervention and engineering judgment. However, estimating structural dynamic properties and managing spurious modes remain challenging due to uncertainties in practical application conditions. To address this issue, we propose an automated modal identification approach comprising three key aspects: (1) identification of modal parameters using covariance-driven stochastic subspace identification; (2) automated interpretation of the stabilization diagram; (3) an improved self-adaptive algorithm for grouping physical modes based on ordering points to identify the clustering structure (OPTICS) combined with k-nearest neighbors (KNN). The proposed approach can play a crucial role in enabling real-time structural health monitoring without human intervention. A simulated 10-story shear frame was used to verify the methodology. Identification results from a cable-stayed bridge demonstrate the practicality of the proposed method for conducting AOMA in engineering practice. The proposed approach can automatically identify modal parameters with high accuracy, making it suitable for a real-time structural health monitoring framework.