Design of the prototype low energy beam transport line for the Spallation Neutron Source
Design of the Prototype Low Energy Beam Transport Line for the Spallation Neutron Source * D.W. Cheng † , R.A. Gough, M.D. Hoff, R. Keller, M.A. Leitner, K.N. Leung, J.W. Staples, M.D. Williams, Earnest Orlando Lawrence Berkeley National Laboratory, Berkeley, CA 94720 Abstract The design of the Spallation Neutron Source (SNS) prototype low-energy beam transport (LEBT) system is discussed. This LEBT must transfer 35 mA of H- current from the ion source outlet aperture to the entrance of the radio-frequency quadrupole (RFQ). The plasma generator is a radio frequency-driven multicusp source, operated at 6% duty factor (1 ms, 60 Hz). The entire LEBT configuration is electrostatic, with a high-voltage extraction gap followed by two sets of einzel lenses. The second einzel lens will be split into four quadrants to permit the application of transverse steering and beam chopping fields. The H- ion source emits a gas flow into the LEBT that must be efficiently pumped to reduce stripping losses of the H- ions. Therefore, an efficient electrode design is incorporated to reduce the gas pressure between the electrodes. Alignment requirements and related issues will also be discussed. 1 INTRODUCTION The Spallation Neutron Source front end systems, being built at the Lawrence Berkeley National Laboratory (LBNL), must supply a 2.5 MeV, 28 mA H - beam at 6% duty factor to a 1GeV linac that injects into an accumulating ring. This ring then delivers a 1 MW average beam power to a neutron production target at 60 Hz. This paper discusses the design of the low energy beam transport (LEBT) line of the front end accelerator system. Figure 1. Cross section of the LEBT electrodes, with the ion source outlet aperture, electron dump, and RFQ endwall. section of the lens configuration. Because of the limited space, voltage holding and creepage length along the surface of insulators must be taken into consideration. Table 1 summarizes the design parameters used. In addition, alignment for these electrodes must be held to a ±0.05 mm tolerance in the radial direction, and ±0.1 mm in the z (beam) direction. Table 1. Criteria for voltage holding used. *units of d are cm, units of U are kV Gap: Insl. Surface: 2 REQUIREMENTS The LEBT is designed to transport 35 mA of a 65 keV H - beam from an rf-driven source to the RFQ, operating at a 6% duty factor. It must match the beam to the RFQ entrance with a normalized emittance of less than 0.15 π mm•mrad and Twiss parameters, α = 1.6, and β = 6.5 cm. The entire LEBT is electrostatic, with a high-voltage (~80 kV) extraction gap and an einzel lens configuration with beam chopping and steering capabilities incorporated into the second (G5) lens electrode. The entire package is approximately 10 cm in length. Figure 1 shows a cross- This research is sponsored by the Lockheed Martin Energy Research Corporation under the U.S. Department of Energy, Contract No. DE- AC05-96OR22464, through the Lawrence Berkeley National Laboratory under contract No. DE-AC03-76SF00098. in Vacuum * d = ( 0 . 0141 U 3 / 2 ) / 10 15 kV/cm in Air 10 kV/cm 8 kV/cm 3 ELECTRODE DESIGN 3.1 Extractor Electrode The extractor electrode consists of three sub-parts: the main stainless-steel spider-arm”, a retainer ring, and the aperture insert held in place by the ring (see Figure 1). The aperture insert is replaceable in case of accidental damage by hitting of the beam particles. Therefore, the aperture is designed to be accessible and replaceable without affecting the alignment of the entire LEBT assembly. We will use copper, as opposed to stainless steel, for the insert material because of its excellent thermal conductivity. We will also consider other Email: dwcheng@lbl.gov
Read more