CFD Modeling for Optimizing the Fluid Dynamics Patterns of Refractory Lining Drying Process in a Vertical Lime Kiln

Computational fluid dynamics (CFD) models are powerful computational tools to simulate urban-landscape scale atmospheric dispersion events. They are proven to be very useful for security management and emergency response. Essential inputs to CFD models include landscape characteristics, which are often captured by various GIS data layers. While it is logical to couple GIS and CFD models to take advantage of available GIS data and the visualization and cartographic rendering capabilities of GIS, the integration of the two tools have been minimal. In this paper, we took the first step to evaluate the use of GIS data in CFD modeling. Specifically, we explore how efficient is to use GIS data in CFD models and how sensitive the CFD results are to different GIS data formats. Using campus topography and building data, and the FEFLO-URBAN CFD model, we performed atmospheric release simulations using topographic data in contour and raster formats. We found that using raster format was quite efficient and contour data required significant effort. Though the simulation outputs from the two data formats were not identical, their overall outcomes were similar and did not post alarming discrepancies. We concluded that using GIS data have tremendous potential for CFD modeling.

An analysis and development method for augmenting flow and pressure performance of electronic cooling axial fans using a fixed vane stator is established using classical hand calculations, 2-dimensional (2D) Computational Fluid Dynamics (CFD) analysis, data from a design of experiments, and 3-dimensional (3D) CFD modeling. Where the size of electronic enclosures may disallow an increase in diameter of axial fans but allow for an increase in depth; a fixed vane stator is implemented to recapture lost dynamic pressure associated with swirl and radial flow vectors from the axial fan blades thus augmenting the pressure/flow curve of the unit. Stator blade effectiveness is evaluated and optimized first using data associated with National Advisory Committee for Aeronautics (NACA) airfoil shapes and then using 2-dimensional (2D) CFD analyses on both the impeller and stator blades. CFD modeling approaches and solving methods are discussed. A Design of Experiments (DOE) is utilized to verify and optimize the performance of the stator vanes and identifies the effectiveness of the stator vane angle, curvature of the stator leading edge, and number of stator vanes. At a constant back pressure the best performing DOE geometry delivered a 22% improvement in flow at constant electrical power input and a 41% improvement in flow at constant acoustic noise. This result was confirmed using a 3D CFD modeling. This analysis and development method provides a good baseline for evaluating and choosing proper stator vane geometries for flow improvement in axial fans.

This paper presents the first simulation model of a tilting pad journal bearing (TPJB) using three-dimensional (3D) computational fluid dynamics (CFD), including multiphase flow, thermal-fluid, transitional turbulence, and thermal deformation of the shaft and pads employing two-way fluid–structure interaction (FSI). Part I presents a modeling method for the static performance. The model includes flow between pads BP, which eliminates the use of an uncertain, mixing coefficient (MC) in Reynold's equation approaches. The CFD model is benchmarked with Reynold's model with a 3D thermal-film, when the CFD model boundary conditions are consistent with the Reynolds boundary conditions. The Reynolds model employs an oversimplified MC representation of the three-dimensional mixing effect of the BP flow and heat transfer, and it also employs simplifying assumptions for the flow and heat transfer within the thin film between the journal and bearing. This manufactured comparison shows good agreement between the CFD and Reynold's equation models. The CFD model is generalized by removing these fictitious boundary conditions on pad inlets and outlets and instead models the flow and temperature between pads. The results show that Reynold's model MC approach can lead to significant differences with the CFD model including detailed flow and thermal modeling between pads. Thus, the CFD approach provides increased reliability of predictions. The paper provides an instructive methodology including detailed steps for properly applying CFD to tilt pad bearing modeling. Parts I and II focus on predicting static and dynamic response characteristic responses, respectively.

Computational fluid dynamics (CFD) model has been widely used for prototyping data centers. Evolving it to high-fidelity {\em digital twin} is desirable for the management and operations of large-scale data centers. Manually calibrating CFD model parameters to achieve twin-class fidelity by specially trained domain expert is tedious and labor-intensive. To reduce manual efforts, existing automatic calibration approaches developed for various computational models apply heuristics to search model configurations within an empirically defined parameter bound. However, in the context of CFD, each search step requires long-lasting CFD model's iterated solving, rendering these approaches impractical with increased model complexity. This paper presents Kalibre, a knowledge-based neural surrogate approach that performs CFD model calibration by iterating four key steps of i) training a neural surrogate model based on CFD-generated data, ii) finding the optimal parameters at the moment through neural surrogate retraining based on sensor-measured data, iii) configuring the found parameters back to the CFD model, and iv) validating the CFD model using sensor-measured data as the ground truth. Thus, the parameter search is offloaded to the neural surrogate which is ultra-faster than CFD model's iterated solving. To speed up the convergence of Kalibre, we integrate prior knowledge of the twinned data center's thermophysics into the neural surrogate design to improve its learning efficiency. With about five hours computation on a 32-core processor, Kalibre achieves mean absolute errors (MAEs) of $0.81^o$C and $0.75^o$C in calibrating two CFD models for two production data halls hosting thousands of servers each while requires fewer CFD solving processes than existing baseline approaches.

A numerical investigation was performed to study the variation in axial and lateral velocity profiles occurring downstream of the inlet nozzle of a typical Westinghouse 17×17 PWR fuel assembly. A Computational Fluid Dynamic (CFD) model was developed with commercial CFD software. The model comprised the lower region of the fuel assembly, including: the Debris Filter Bottom Nozzle (DFBN), P-grid, Bottom Inconel grid, one and half grid span, as well as the lower core plate hole. The purpose of the study was to obtain insight into the flow redistribution resulting from the interaction of the jet arising from the lower core plate hole and the fuel assembly structure. In particular the axial and lateral velocities before and after the nozzle were studied. The results, axial and lateral velocity contours, streamlines and maximum axial and lateral velocity distributions at various elevations are presented and discussed in relation to the potential risk of high turbulent excitation over the rod and the resulting rod-to-grid fretting-wear damage. The CFD model results indicated that the large jet flows from the lower core plate are effectively dissipated by DFBN nozzle and the grids components of the fuel assembly. The breakup of the large jets in the DFBN and the lower grids helps to reduce the steep velocity gradients and thus the rod vibration and fretting-wear risk in the lower part of the fuel assembly. The presented CFD model is one step towards developing advanced tools that can be used to confirm and evaluate the effect of complex PWR structures on flow distribution. In the future the presented model could be integrated in a larger CFD model involving several fuel assemblies for evaluating the lateral velocities generated due to the non-uniform inlet conditions into the various fuel assemblies.

Computational fluid dynamics (CFD) modelling and optimum gap size of a compact steam methane reforming (SMR) reactor

The effects of an apartment complex on flow and pollutant dispersion in an urban area are numerically investigated using a computational fluid dynamics (CFD) model. The CFD model is based on the Reynolds-averaged Navier-Stokes equations and includes the renormalization group k- turbulence model. The geographic information system (GIS) data is used as an input data of the CFD model. Eight numerical simulations are carried out for different inflow directions and, for each inflow direction, the effects of an apartment complex are investigated, comparing the characteristics of flow and dispersion before and after construction of the apartment complex in detail. The observation data of automatic weather system (AWS) is analyzed. The windrose analysis shows that the wind speed and direction after the construction of the complex are quite different from those before the construction. The construction of the apartment complex resulted in the decrease in wind speed at the downwind region. It is also shown that the wind speed increased partially inside the apartment complex due to the channeling effect to satisfy the mass continuity. On the whole, the wind speed decreased at the downwind region due to the drag effect by the apartment complex. As a result, the passive pollutant concentration increased (decreased) near the downwind region of (within) the apartment complex compared with that before the construction.

Wind tunnel and CFD study of dust dispersion from pesticide-treated maize seed

The lack of accurate submodels for in-cylinder radiation and heat transfer has been identified as a key shortcoming in developing truly predictive, physics-based computational fluid dynamics (CFD) models that can be used to develop and design combustion systems for advanced high-efficiency, low-emissions engines. Measurements of wall boundary layers in engines show discrepancies of up to 100% with respect to standard CFD boundary layer models. And analysis of in-cylinder radiation based on the most recent spectral property databases and high-fidelity radiative transfer equation solvers has shown that at operating pressures and exhaust-gas recirculation levels typical of modern compression-ignition truck engines, molecular gas radiation (mainly carbon dioxide and water vapor) can be more important than soot particle radiation, and that a significant fraction of the emitted radiation (50% or more) can be reabsorbed before reaching the walls, thereby acting to redistribute energy in the combustion chamber. In this project, an integrated experimental and simulation approach has been used to generate new physical insight into in-cylinder heat-transfer processes in engines, and to develop computationally practicable CFD-based models that accurately represent the physics. New experimental data have been taken in an optically accessible single-cylinder research engine, and in a multi-cylinder production engine. Those data have provided new insight into the radiative environment in engines. New CFD models have been developed and validated for in-cylinder heat transfer, focusing mainly on radiative heat transfer and coupling between turbulent boundary layer wall heat transfer and radiative heat transfer. The CFD models have been developed and implemented in an open-source software framework that can be shared with other researchers. The models are compatible both with unsteady Reynolds-averaged Navier Stokes (URANS) formulations and with large-eddy simulations (LES) of in-cylinder processes in engines.

Pulverized coal fired combustion is a major contributor to global emissions of nitric oxide (NO). Release of NO into the atmosphere causes toxic NO, reduction of ozone, formation of smog, and reduced visibility. Computational fluid dynamic (CFD) modelling of NO emissions from pulverized coal fired boilers offers several benefits including optimisation of boiler operating conditions to minimize NO emissions and development of low NO technology. Formation of NO within a pulverized coal fired boiler is a complex process, yet simple mechanisms are used to approximate the formation process. CFD modelling of NO formation requires prediction of the 1. nitrogen release rate from coal during devolatilization and char combustion, 2. possibly the type of nitrogen compound released during devolatilization and char combustion, 3. gas phase conversion of nitrogen compounds to NO (including possible NO reduction mechanisms), 4. contributions of thermal and prompt NO, and 5. conversion of char nitrogen to NO. This thesis assessed currently used models for processes 1-5 for accuracy and reliability in simple systems and CFD modelling. Models for processes 1-5 were improved, if required. CFD models currently assume the rate of nitrogen release equals a times the carbon release rate, where a equals 1. Laboratory and utility boiler measurements showed that a varies between 0.8 and 1.2. The sensitivity of a to NO emissions should be tested in CFD models for a variety of cases. If NO emissions are sensitive to a, a value of 1.07 is recommended for utility boilers as estimated from utility boiler measurements. The type of nitrogen compound released during devolatilization and char combustion may affect the reaction kinetics converting nitrogen compounds to NO. Previous laboratory measurements concluded that HCN and NH3 are the major nitrogen compounds released during devolatilization. The most likely compound released during char combustion is NO. The conversion of HCN and NH3 to NO was found to vary in fuel-rich conditions at temperatures between 1200 K and 2000 K. Therefore a NO prediction model should include conversion of HCN and NH3 to NO. Currently used global kinetic mechanisms were found to inadequately predict NO formation. Commonly used thermal NO mechanisms significantly over-predict NO formation at temperatures greater than 2200 K and long residence times. This trend is not critical in coal-fired systems because maximum temperatures are less than 2000 K. The de Soete mechanism is commonly used to predict the conversion of HCN to NO. This mechanism was found to under-predict NO formation at temperatures less than 1700 K. The de Soete mechanism was adjusted to improve predictions at low temperatures. An investigation into the use of reduced reaction mechanisms found it was not theoretically possible to reduce a comprehensive reaction mechanism to the extent it could be incorporated into a CFD model, and solve within the same simulation time as a CFD model using global kinetics. An empirical equation was developed that fits the profile of NO formation and HCN destruction. The equations fit NO and HCN profiles across a wide range of conditions. Values of NO and HCN at conditions other than the simulated ones are calculated by interpolation. This mechanism offers an alternative approach to prediction of NO formation by global kinetic mechanisms. Currently available char nitrogen to NO equations are simple, and do not consider parameters such as char size, temperature and char surface area. Empirical equations were developed to calculate the conversion of char nitrogen to NO given the char size, temperature, O2 concentration, NO concentration, char surface area and intrinsic reactivity. The accuracy and reliability of NO predictions determined by CFD models was assessed by comparison of model predictions and utility boiler measurements. CFD models were assessed by four criteria including how accurately NO emissions were predicted, how accurately NO profiles and profiles of species important to NO formation within the burner region were predicted, how accurately temperature and O2 concentrations were predicted and how accurately the model predicted trends in NO emissions as combustion conditions changed. The CFD model investigated, Furnace, could not satisfy the set criteria and therefore modelling results should be interpreted carefully.n

At present, fossil-fuel power plants supply the majority of the world’s demand of electric energy. The environmental and health threats from anthropogenic emissions of greenhouse gases (GHG) of these power plants have been considered as one of the main reasons for global climate change. In order to make the existing fossil fuel energy sources more environmentally friendly, a new generation of advanced power plant with increased output and environmental performance is required to be built. Oxy-fuel combustion technique can potentially provide significant opportunities for near-zero emissions from the existing and new-build power plants by capturing and storing the carbon dioxide emissions from burning fossil fuels and biomass. To obtain a better understanding of the overall oxy-fuel combustion process, it is important to investigate the effects of oxy-fuel-fired conditions on the combustion characteristics and heat transfer performance as innovations in the energy used. As a first step in developing and validating a computational tool to numerically model combustion of gaseous fuel, a computational fluid dynamics (CFD) modelling study has been carried out involving propane combustion with associated chemical reactions, radiative heat transfer, and turbulence. Three different combustion environments that were adopted experimentally in a 100 kW drop tube firing unit, were examined. One air-fired (reference case) and two oxy-fuel-fired cases (21 vol.% O2 for one combustion case (OF21) and 27 vol.% O2 for the other combustion case (OF27)) were investigated. The irreversible singlestep and reversible multi-step reaction mechanisms were considered. The results obtained with the multi-step chemistry mechanism showed improved agreement, particularly in the flame zone. The unburnt fuel in air-fired and OF27 cases was less than that of the OF21 case due to the low oxygen concentration used in the latter combustion case. As a second step of this research program, a comprehensive CFD modelling study was undertaken by integrating the combustion of pulverized dry lignite in several combustion environments. Four different cases were investigated: an air-fired and three different oxy-fuel combustion environments (25 % vol. O2 concentration (OF25), 27 % vol. O2 concentration (OF27), and 29 % vol. O2 concentration (OF29) were considered. The available experimental results from a lab-scale 100 kW firing lignite unit (Chalmers’ furnace) were selected for the validation of these simulations. The findings showed reasonable agreement with the qualitative and quantitative measurements of temperature distribution profiles and species concentration profiles at the most intense combustion locations inside the furnace. Through the use of Computational Fluid Dynamics (CFD), it is concluded that the resident time, stoichiometry, and recycled flue gas rates are relevant parameters to optimize the design of oxy-fuel furnaces. Under the same oxy-fuel combustion conditions as above, the appropriate mathematical models with the related kinetics parameters were implemented. The purpose was to accurately calculate the temperature distributions, species concentrations (O2, CO2, CO, H2O, and H2), NOx emission concentrations, and the radiation heat transfer. In this step of the modelling investigation, the multi-step chemical reaction mechanisms were conducted on the gas-phase and solid-phase of the coal reaction in one-, two-, and three-step reaction schemes. The predicted results showed a reasonably good agreement against the measured data for all the combustion cases, but in the three-step scheme the results were highly improved, particularly in the flame envelope zone. In the final step of the investigation, a computational fluid dynamics (CFD) modelling study has been developed to investigate Victorian brown coal combustion in a 550 MW utility boiler under air-fired and three oxy-fuel-fired scenarios. User-defined functions (UDFs) were written and incorporated into the CFD code in order to calculate the following mathematical models: the PC devolatilization, char burnout, multi-step chemical reactions, mass and heat transfer, carbon in fly-ash, and NOx formation/destruction. A level of confidence of the CFD model was achieved by validating four different parameters of the conventional combustion case. The numerical results of OF29 combustion condition were considerably similar to the reference firing results in terms of gas temperature levels and radiative heat transfer relative to the OF25 and OF27 combustion cases. In addition, a significant increase in the CO2 concentrations and a noticeable decrease in the NOx formation were observed under all oxy-fuel combustion scenarios. This study of oxy-fuel combustion in a large-scale tangentially-fired boiler is important prior to its implementation in real-life.

The constant development of aero engines towards lighter but yet more compact designs, without decreasing their efficiency, has led to gradually increased demands of the lubrication systems, such as the bearing chambers of the aero engine. For this reason, it is of particular importance to increase our level of understanding of the flow field inside the bearing chambers in order to optimize its design and performance. The flow field in such cases is of a complicated nature since there is a strong interaction between air-flow and lubricant oil together with the geometrical configurations and the shaft rotational speed inside the bearing chamber. The behavior of this interaction must be investigated in order to understand the flow field development inside the aero engine bearing and, at a next step, optimize its performance in relation to the lubrication and heat transfer capabilities. Such an effort is presented in this work where an investigation of the air-flow field development inside the front bearing chamber of an aero engine is attempted. The front bearing chamber is divided in two separate smaller sections where the flow passes from the first section partially through the bearing and the holding structure, to the second one where the vent and the scavenge are placed. The investigation was performed with the combined use of experimental measurements and Computational Fluid Dynamics (CFD) modeling. The experimental measurements were carried out with the use of a Laser Doppler Anemometry (LDA) system in an experimental rig modeling the front bearing chamber of an aero engine for real operating conditions taking into account both air-flow and lubricant oil-flow and for a varying number of shaft rotating speeds. The CFD modeling was performed with the use of a commercial CFD package. The air-flow inside the bearing was modeled with the adoption of a porous medium assumption. The experimental measurements and the CFD computations presented similar flow patterns and satisfactory quantitative agreement. At the same time the effect of the important parameters such as the air and oil mass flow together with the shaft rotation speed and the effect of the chamber inside geometry were identified. These conclusions can be exploited in future attempts in combination with the developed CFD model, in order to optimize the efficiency of the lubricant and cooling system. The latter forms the main target of this work which is the development of a useful engineering tool capable of predicting the flow field inside the aero engine bearing so as to be used for optimization efforts.

Urban environmental problem became one of major issues during its urbanization processes. Environmental impacts are assessed during recent urban planning and development. Though the environmental impact assessment considers meteorological impact as a minor component, changes in wind environment during development can largely affect the distribution pattern of air temperature, humidity, and pollutants. Impact assessment of local wind is, therefore, a major element for impact assessment prior to any other meteorological impact assessment. Computational Fluid Dynamics (CFD) models are utilized in various fields such as in wind field assessment during a construction of a new building and in post analysis of a fire event over a mountain. CFD models require specially formatted input data and produce specific output files, which can be analyzed using special programs. CFD's huge requirement in computing power is another hurdle in practical use. In this study, a CFD model and related software processors were automated and integrated as a microscale wind environmental impact assessment system. A supercomputer system was used to reduce the running hours of the model. Input data processor ingests development plans in CAD or GIS formatted files and produces input data files for the CFD model. Output data processor produces various analytical graphs upon user requests. The system was used in assessing the impacts of a new building near an observatory on wind fields and showed the changes by the construction visually and quantitatively. The microscale wind assessment system will evolve, of course, incorporating new improvement of the models and processors. Nevertheless the framework suggested here can be utilized as a basic system for the assessment.

One of the main factors affecting the use of lasers in the industry for welding thick structures is the process accompanying solidification cracks. These cracks mostly occurring along the welding direction in the welding center, and strongly affect the safety of the welded components. In the present study, to obtain a better understanding of the relation between the weld pool geometry, the stress distribution and the solidification cracking, a three-dimensional computational fluid dynamic (CFD) model was combined with a thermo-mechanical model. The CFD model was employed to analyze the flow of the molten metal in the weld pool during the laser beam welding process. The weld pool geometry estimated from the CFD model was used as a heat source in the thermal model to calculate the temperature field and the stress development and distributions. The CFD results showed a bulging region in the middle depth of the weld and two narrowing areas separating the bulging region from the top and bottom surface. The thermo-mechanical simulations showed a concentration of tension stresses, transversally and vertically, directly after the solidification during cooling in the region of the solidification cracking.

In the present study, a Computational Fluid Dynamics (CFD) model was set up to analyse the dynamic behaviour of LNG (Liquefied Natural Gas) tanks adopted in heavy trucks refuelling stations in normal operating conditions or during process upsets. The CFD model was based on the Volume-Of-Fluid (VOF) method to simulate the transient behaviour of a multi-phase flow in a 100 m3 vertical cylindrical tank. The model first considered a fully insulated vessel, and subsequently it was modified to take into account possible damages of the insulation layer, this being a critical upset scenario. The CFD model allowed predicting the dynamic pressure build up in the damaged tank, thus obtaining key indications for the evaluation of the vessel mechanical resistance and set up of safety measures. The model also provided the prediction of vapor temperature with respect to time and external heat source, that is a key issue to assess the effectiveness of the thermal insulation.