Comment on egusphere-2022-956

The computational fluid dynamical software AVL-FIRE code was used for investigating the impact of multiply injection strategies and spray included angles on combustion and emissions in a marine diesel engine. The fuel injection parameters of spray included angle and pilot injection timing with pilot-main injection, as well as post injection ratio and post injection duration angle with pilot-main-post injection, were all investigated and optimized. The results indicate that retarding pilot injection timing with pilot-main injection declines high temperature region, resulting in a notable reduction in NOx emissions. Since fuel evaporation and burn are hampered by long spray penetration due to low temperature and pressure with pilot injection, a suitable spray included angle are used to offer more efficient air-fuel mixing process. A wider spray included angle simultaneously reduces soot emission and indicated specific fuel consumption (ISFC). Post injection fuel exerts impact on combustion process by causing a great disturbance to flow field during post combustion. Increasing post injection ratio from 4% to 10% at a small post injection duration angle great emission performance is achieved by simultaneous reduction in NOx and soot emissions while only using a slight consumption of ISFC. To summarize, the defeat of traditional NOx-soot trade-off occurs as both NOx and soot emissions are decreased with optimized multiple injection strategy and spray included angle. Particularly, there are respectively four cases with pilot-main injection and two cases with pilot-main-post injection, that achieve simultaneous reduction in NOx emissions, soot emission, and ISFC, compared to the prototype.

Experimental and numerical studies were performed to investigate the simultaneous reduction of NOx and CO for stoichiometric diesel combustion with a 3-way catalyst. A single-cylinder engine was used for the experiments and KIVA simulations were used in order to characterize the combustion efficiency and emissions of throttled stoichiometric diesel combustion at 0.7 bar boost pressure and 90MPa injection pressure. In addition, the efficiency of emission conversion with the 3-way catalysts in stoichiometric diesel combustion was investigated experimentally. The results showed CO and NOx emissions can be controlled with the 3-way catalyst in spite of the fact that CO increases more at high equivalence ratios compared to conventional diesel combustion (i.e., lean combustion). At stoichiometric operation, the 3-way catalyst reduced CO and NOx emissions by up to 95%, which achieves lower emissions compared to conventional diesel combustion or low temperature diesel combustion, while keeping better fuel consumption than a comparable gasoline engine.

Experimental and numerical studies were performed to investigate the simultaneous reduction in NOx and CO for stoichiometric diesel combustion with a three-way catalyst. A single-cylinder engine was used for the experiments and KIVA simulations were used in order to characterize the combustion efficiency and emissions of throttled stoichiometric diesel combustion at 0.7 bar boost pressure and 90 MPa injection pressure. In addition, the efficiency of emission conversion with three-way catalysts in stoichiometric diesel combustion was investigated experimentally. The results showed CO and NOx emissions can be controlled with the three-way catalyst in spite of the fact that CO increases more at high equivalence ratios compared with conventional diesel combustion (i.e., lean combustion). At a stoichiometric operation, the three-way catalyst reduced CO and NOx emissions by up to 95%, which achieves lower emissions compared with conventional diesel combustion or low temperature diesel combustion, while keeping better fuel consumption than a comparable gasoline engine.

Impact of H2 addition on flame stability and pollutant emissions for an atmospheric kerosene/air swirled flame of laboratory scaled gas turbine

Small Diesel engines pose a very tough challenge of simultaneously meeting NOx and particulate matter (PM) emissions, without hampering performance and fuel consumption. Frequent revision in small diesel engines pose a very tough challenge of simultaneously meeting NOx and PM emissions, without hampering performance and fuel consumption. Frequent revision in emission norms for small diesel engines makes it further difficult, as they need to be upgraded in design and for combustion. These small, low-capacity engines are predominantly used in specific regions/countries where cost plays a major role and hence these engines lack a clear emission reduction strategy. It is required to develop an emission reduction strategy considering available technologies and cost implications. Current research work aims to develop a cost-effective emission reduction strategy by modifying the engine using conventional technologies. The present work is an experimental study of the effect of cylinder head Swirl, static injection timing (SIT), intake valve opening (IVO), and Exhaust gas recirculation (EGR) on a 0.4 l single-cylinder diesel engine's performance and emission. Baseline vehicle has HC+NOx and PM emission levels are 0.61 g/kM and 0.04 g/KM, respectively; which is higher considering existing and upcoming emission norms. The lower Swirl cylinder head, advanced IVO timings with retarded injection timings shows an 18% reduction in NOx emission with a 3% improvement in performance at the engine dynamometer. Different EGR rates were also studied and effects were analyzed on emission and fuel consumption and emissions. EGR rate of 25% with advanced IVO of 16° with SIT of 5° and 1.9 Swirl cylinder head had shown 48% improvement in HC+NOx emissions, 20% improvement in PM emission, and 11% improvement on CO emissions at the Chassis dynamometer.

In this study, real voyage data and ship specifications of a general cargo ship are employed, and it is assumed that diesel generators are replaced with hydrogen proton exchange membrane fuel cells. The effect of the replacement on CO2, NOX, SOX, and PM emissions and the CII value is calculated. Emission calculations show that there is a significant reduction in emissions when hydrogen fuel cells are used instead of diesel generators on the case ship. By using hydrogen fuel cells, there is a 37.4% reduction in CO2 emissions, 32.5% in NOX emissions, 37.3% in SOX emissions, and 37.4% in PM emissions. If hydrogen fuel cells are not used instead of diesel generators, the ship will receive an A rating between 2023 and 2026, a B rating in 2027, a C rating in 2028–2029, and an E rating in 2030. On the other hand, if hydrogen fuel cells are used, the ship will always remain at an A rating between 2023 and 2030. The capital expenditure (CAPEX) and operational expenditure (OPEX) of the fuel cell system are USD 1,305,720 and USD 2,470,320, respectively, for a 15-year lifetime, and the hydrogen fuel expenses are competitive at USD 260,981, while marine diesel oil (MDO) fuel expenses are USD 206,435.

Real world CO2 and NOx emissions from 149 Euro 5 and 6 diesel, gasoline and hybrid passenger cars

Simultaneous reduction of NOx emission and SOx emission aided by improved efficiency of a Once-Through Benson Type Coal Boiler

This study evaluates the effects of Al2O3 and CeO2 nanoparticles as additives to standard diesel and biodiesel fuels on the combustion and emissions characteristics of a CR diesel engine with split injection (pilot and main injections). Three nanoparticle dosing levels (50 ppm, 100 ppm, and 150 ppm) were compared with undoped standard diesel and biodiesel fuels. The results showed that the presence of both Al2O3 and CeO2 in biodiesel increased the ignition delay of the pilot fuel by about 8.0% at low load and about 3.5% at high load. The addition of both nanoparticles to diesel and biodiesel fuels had an insignificant effect on the main injection fuel’s ignition delay, MBF50 position and combustion duration. The thermal efficiency was up to 1.0% lower. Al2O3 additive in diesel had no significant effect on NOx emissions. CO emissions were higher by 4.4–7.5% in most cases. The Al2O3 additive in biodiesel reduced NOx emissions by an average of 38%, 17.1%, and 9.4% at low, medium, and high engine loads, respectively. The reduction in CO emissions averaged 15%. The addition of CeO2 nanoparticles to diesel fuel reduced NOx emissions by 22.5%, 8.5%, and 3.1% on average across the corresponding load ranges. When the engine was operated on CeO2-doped biodiesel, NOx emissions were lower by an average of 25.7%, 9.6%, and 2.5% at low, medium, and high loads, respectively. Adding CeO2 nanoparticles to diesel fuel increased CO emissions, whereas adding them to biodiesel significantly reduced CO emissions.

The historic trend of the levels of gaseous H2O2 during 1960's–1980's in Los Angeles was assessed from field date and numerical simulations. The results indicate that during 1960's–1970's concentrations of H2O2, as well as O3, were likely to have been higher than those during 1980's, For the period 1969–1987, predicted summer peak concentrations of H2O2 and O3 in the ground level atmosphere were in a range of 6–10 ppb and 200–350ppb, respectively. Also H2O2 and 03 concentrations decreased by about 35% and 42% respectively from the levels of 1975 to 1987. Model simulations indicated that the reduction of NMHC and CO emissions from industrial and automotive sources have resulted in the decrease in H2O2 levels during the late 1970's–1980's, whereas the reduction of NMHC, CO and NOx emissions have resulted in lower O3 levels. The role of H2O2 as an oxidant for SO2 and as a possible toxin on trees in Los Angeles and surrounding mountains during the past decades are discussed. From the historic data of atmospheric levels of sulfate in Los Angeles, we suggest that the decrease in the levels of H2O2 and O3 may have contributed to the decrease in sulfite levels during the 1980's.

In the current study, the influence of pressure and steam on the emission formation in a premixed natural gas flame is investigated at pressures between 1.5 bar and 9 bar. A premixed, swirl-stabilized combustor is developed that provides a stable flame up to very high steam contents. Combustion tests are conducted at different pressure levels for equivalence ratios from lean blowout to near-stoichiometric conditions and steam-to-air mass ratios from 0% to 25%. A reactor network is developed to model the combustion process. The simulation results match the measured NOx and CO concentrations very well for all operating conditions. The reactor network is used for a detailed investigation of the influence of steam and pressure on the NOx formation pathways. In the experiments, adding 20% steam reduces NOx and CO emissions to below 10 ppm at all tested pressures up to near-stoichiometric conditions. Pressure scaling laws are derived: CO changes with a pressure exponent of approximately −0.5 that is not noticeably affected by the steam. For the NOx emissions, the exponent increases with equivalence ratio from 0.1 to 0.65 at dry conditions. At a steam-to-air mass ratio of 20%, the NOx pressure exponent is reduced to −0.1 to +0.25. The numerical analysis reveals that steam has a strong effect on the combustion chemistry. The reduction in NOx emissions is mainly caused by lower concentrations of atomic oxygen at steam-diluted conditions, constraining the thermal pathway.

Analysis of combustion and emissions characteristics of a DI diesel engine fuelled with diesel/biodiesel/glycerol tert-butyl ethers mixture by altering compression ratio and injection timing

Effects of biodiesel-ethanol and biodiesel-butanol blends on the combustion, performance and emissions of a diesel engine

• EGR contributed to further reductions in NOx emissions in RCCI combustion. • Improvements in BTE and BSFC were achieved by using EGR in RCCI combustion. • Better RCCI operation with EGR requires an alternating premixed fraction. • Increased biodiesel dose in DI-Fuel lead to an increment in NOx emissions. Exhaust gas recirculation (EGR) seems to be a critical parameter in developed RCCI operations for controlling emissions, in-cylinder charge reactivity as well as combustion phasing. The most advantages of utilizing the RCCI burning technique are the simultaneous decrease of PM as well as NOx emissions. Nevertheless, significant challenges remain, such as extreme HC and CO emissions. The purpose of this work is to investigate the effects of external, hot, and high-pressure EGR as well as different DI-Fuels on RCCI combustion under various load conditions. The tests were performed on direct injection, single-cylinder, and four-stroke modified diesel engine (peak power 5 KW under 1500 rpm) operating in RCCI mode with an EGR system. To initiate ignition, high reactivity fuel (biodiesel/diesel blends) was injected directly inside the engine's cylinder whereas low reactivity fuel (LPG) was induced into to intake mixing chamber. EGR at various ratios (30%, 20%, and 10%) was introduced into the engine via the intake mixing chamber, and experiments were done under various loads. The results show that increasing EGR results in a slight increment in BTE under medium and high engine loads. NOx emissions from diesel engines operating in traditional RCCI mode declined dramatically, and they decreased even further with the addition of EGR. The CO and HC emission levels, on the other hand, are slightly greater when EGR is used. Increasing the proportion of biodiesel in DI-Fuel is resulting in a decrement in BTE and NOx emissions in addition to an increment in BSFC, CO, and HC emissions.

Assessing the performance of the transport sector within the global supply chain context: Decomposition of energy and environmental productivity