Common part estimation of acoustic feedback paths in hearing aids optimizing maximum stable gain

In adaptive feedback cancellation the computational complexity and the convergence speed are determined by the number of adaptive parameters used to model the acoustic feedback path. Therefore it has been proposed to reduce the number of adaptive parameters by modeling the feedback path as the convolution of a time-invariant common part and a time-varying variable part. While previous approaches have modeled the common part either using only poles or using only zeros, in this paper we propose to use a common pole-zero model and present an iterative method to compute the common poles and zeros. Using measured acoustic feedback paths from a two-microphone behind-the-ear hearing aid it is shown that the proposed model enables either to increase the modeling accuracy given a fixed number of parameters of the variable part or to reduce the number of parameters of the variable part given a desired accuracy.

In adaptive feedback cancellation the convergence speed and the computational complexity depend on the number of adaptive param-eters used to model the acoustic feedback path. To improve the convergence speed and reduce the computational complexity, it has been proposed to model the acoustic feedback path as the convolution of a time-invariant common pole-zero part and a time-varying variable part. Previous approaches to estimate all the coefficients minimized the so-called equation-error which possibly suffers from poor estimation accuracy in the vicinity of prominent spectral regions, e.g., spectral peaks. In this paper we therefore propose to minimize the so-called output-error by using a Steiglitz-McBride-like iteration scheme. To ensure the stability of the estimated pole-zero filter a frequency domain constraint is used leading to a quadratic programming problem. Experimental results using measured impulse responses from a two-microphone behind-the-ear hearing aid show that the proposed estimation scheme outperforms the existing estimation scheme in terms of modeling accuracy.

Acoustic feedback in hearing aids occurs due to the coupling between the hearing aid loudspeaker and microphones. In order to reduce acoustic feedback, adaptive filters are often used to estimate the feedback path. To increase the convergence speed and decrease the computational complexity of the adaptive algorithms, it has been proposed to split the acoustic feedback path into a time-invariant fixed part and a time-varying variable part. A key question of this approach is how to determine the fixed part. In this paper, two approaches are investigated: (1) a digital filter design approach that makes use of the signals of at least two hearing aid microphones and (2) a defined physical location approach using an electro-acoustic model and the signals of one hearing aid microphone and an additional ear canal microphone. An experimental comparison using measured acoustic feedback paths showed that both approaches enable one to reduce the number of variable part coefficients. It is shown that individualization of the fixed part increases the performance. Furthermore, the two approaches offer solutions for different requirements on the effort to a specific hearing aid design on the one hand and the effort during the hearing aid fitting on the other hand.

Feedback is a problem in hearing aids which will cause signal degradation and reduce the maximum applicable gain. More specifically, the advantages of open fittings (e.g., minimizing the occlusion effect) are limited by acoustic feedback. Feedback cancelation algorithms are used to overcome these limitations. For the development of such algorithms, the acoustic feedback path of the hearing aid must be known. The acoustic feedback path is not only affected by the outer sound field but by the individual anatomy and physiology as well. In order to quantify these different influences, feedback path measurements were performed on 20 human subjects. The measurements included different static conditions as well as dynamic ones (i.e., repetitive movements were performed during the measurement). Since the sound pressure level must be limited in measurements on human subjects, a valid identification of the feedback path is difficult in many cases, due to a low signal to noise ratio. Therefore, all measurements were performed reciprocally in addition to the direct measurements. Results show that yaw movements only have a small influence on the acoustic feedback path, whereas changes of the outer sound field can have a substantial impact on the feedback path.

Publication in the conference proceedings of EUSIPCO, Antalya, Turkey, 2005

While several proactive acoustic feedback (Larsen-effect) cancellation schemes have been presented for speech applications with short acoustic feedback paths as encountered in hearing aids, these schemes fail with the long impulse responses inherent to, for instance, public address systems. We derive a new prediction error method (PEM)-based scheme (referred to as PEM-AFROW) which identifies both the acoustic feedback path and the nonstationary speech source model. A cascade of a short- and a long-term predictor removes the coloring and periodicity in voiced speech segments, which account for the unwanted correlation between the loudspeaker signal and the speech source signal. The predictors calculate row operations which are applied to prewhiten the speech source signal, resulting in a least squares system that is solved recursively by means of normalized least mean square or recursive least squares algorithms. Simulations show that this approach is indeed superior to earlier approaches whenever long acoustic channels are dealt with

In this paper, we propose a novel solution for continuous acoustic feedback neutralization in the digital hearing aids. The proposed method is based on two adaptive filters working in tandem. The error signal of the first adaptive filter is used as a desired response for the second adaptive filter being excited by a low-level (constant) probe signal. Initially at the start up, the first adaptive filter gives a fast convergence, however, its input and desired response are correlated with each other and it may converge to a biased solution at the steady-state. On the other hand, the second adaptive filter, though converging slowly being excited by a low-level probe signal, would give a good steady-state estimate of the acoustic feedback path. An appropriate delay is inserted at the output of the hearing aid, and based-on this delay-based processing, a novel strategy is proposed to exchange the weights between the two adaptive filters. The proposed strategy is such that the misconvergence of the first adaptive filter is avoided, as well as the initial convergence of the second adaptive filter is improved. Extensive computer simulations are carried out which demonstrate the effectiveness of the proposed method.

Acoustic feedback arises from the leakage of sound from the loudspeaker back to the microphone and is a common problem in hearing aids and public address systems. One popular solution to this problem is adaptive feedback cancellation (AFC) which utilizes an adaptive filter (AF) to estimate and subsequently subtract the feedback component from the microphone. Due to the closed-loop system the loudspeaker signal and the incoming signal exhibit a high correlation. However, model-based and more recently learning-based AF methods typically neglect this correlation in their derivation, leading to sub-optimal performance in closed-loop scenarios. In this paper, we propose Neural-AFC, a recurrent neural network (RNN) designed for AFC step-size control optimization, that addresses this problem by including not only the adaptive filter but also the acoustic feedback path and the system gain in the recurrence model. Our experiment results show that when trained within this closed-loop model, Neural-AFC improves the steady-state performance and (re)convergence rate compared to conventional and open-loop RNN-based AF in both hearing aid and public address system applications.

It is well known that the conventional adaptive algorithm for cancellation of the effect of the feedback path in hearing aids is biased. In this paper the stationary point of a modified adaptive algorithm by splitting the delay in the conventional one is derived by a direct method considering the causality constraint and an explicit expression of the bias is obtained. Also, a stability condition is mentioned. Then, when the input signal to hearing aids is a moving average (MA) process or an autoregressive (AR) process, unbiased algorithms for identification of the feedback path are proposed. It is shown by simulations that the new algorithm for an AR process converges considerably faster than that of the previously proposed two-channel adaptive algorithm.

The role of the external boundary conditions of the nozzle surface on the azimuthal mode selection of impinging supersonic jets is demonstrated for the first time. Jets emanating from thin- and infinite-lipped nozzles at a nozzle pressure ratio of $3.4$ and plate spacing of $5.0D$, where $D$ is the nozzle exit diameter, are investigated using high resolution particle image velocimetry (PIV) and acoustic measurements. Proper orthogonal decomposition is applied to the PIV fields and a difference in dominant instability mode is found. To investigate possible explanations for the change in instability mode, additional nozzle external boundary conditions are investigated, including the addition of acoustic dampening foam. A difference in acoustic feedback path is suggested to be the cause for the change in dominant azimuthal modes between the flows. This is due to the thin-lip case containing a feedback path that is concluded to be closed exclusively by a reflection from the nozzle base surface, rather than directly to the nozzle lip. The ability of the flow to form a feedback path that maximises the impingement tone gain is discussed with consideration of the numerous acoustic feedback paths possible for the given nozzle external boundary conditions.

Adaptive feedback cancellation in hearing aids

Feedback whistling is a severe problem with hearing aids. A typical acoustical feedback path represents a wave propagation path from the receiver to the microphone and includes many complicated effects among which some are invariant or nearly invariant for all users and in all acoustical environments given a specific type of hearing aids. Based on this observation, a feedback path model that consists of an invariant model and a variant model is proposed. A common-acoustical-pole and zero model-based approach and an iterative least-square search-based approach are used to extract the invariant model from a set of impulse responses of the feedback paths. A hybrid approach combining the two methods is also proposed. The general properties of the three methods are studied using artificial datasets, and the methods are cross-validated using the measured feedback paths. The results show that the proposed hybrid method gives the best overall performance, and the extracted invariant model is effective in modeling the feedback path.

Self-adapting variable step size strategies for active noise control systems with acoustic feedback

Criteria for estimating an FIR filter for cancelling the feedback path signal in hearing aid system

The adaptive feedback canceller (AFC) based on the least mean square (LMS) or normalized LMS (NLMS) algorithm shows poor convergence for sparse impulse response, since they do not consider the characteristics of the impulse response. The acoustic feedback path of the hearing aid exhibits sparse characteristics consisting of few active coefficients and many non active (near to zero) coefficient values. This paper proposes an improved gradient controlled improved proportionate NLMS (IGC-IPNLMS) algorithm for cancelling the feedback phenomenon in hearing aids. The IGC-IPNLMS algorithm employs a variable convergence factor, an estimate of the gradient vector for allocating step size, the controlling parameter of the IGC-IPNLMS algorithm is also updated in each iteration based on the sparseness measure. Further, the reduction in computational complexity is achieved by using sparse partial update method along with the IGC-IPNLMS algorithm (SIGC-IPNLMS) for feedback cancellation. The simulation results show the superior performance of the proposed method for white noise and speech segment as input.