Comparative study of IoT forensic frameworks

With the growth of wireless network technology-based devices, identifying the communication behaviour of wireless connectivity enabled devices, e.g. Internet of Things (IoT) devices, is one of the vital aspects, in managing and securing IoT networks. Initially, devices use frames to connect to the access point on the local area network and then, use packets of typical communication protocols through the access point to communicate over the Internet. Toward this goal, network packet and IEEE 802.11 media access control (MAC) frame analysis may assist in managing IoT networks efficiently, and allow investigation of inclusive behaviour of IoT devices. This paper presents network traffic traces data of D-Link IoT devices from packet and frame levels. Data collection experiment has been conducted in the Network Systems and Signal Processing (NSSP) laboratory at Universiti Brunei Darussalam (UBD). All the required devices, such as IoT devices, workstation, smartphone, laptop, USB Ethernet adapter, and USB WiFi adapter, have been configured accordingly, to capture and store network traffic traces of the 14 IoT devices in the laboratory. These IoT devices were from the same manufacture (D-Link) with different types, such as camera, home-hub, door-window sensor, and smart-plug.

Cognitive radio (CR) is considered as a key enabling communication technology that offers efficient wireless connectivity to Internet of Things (IoT) devices. Its integration with the future 5G architecture is expected to advance the IoT paradigm. Security attacks can severely degrade the performance of such CR‐based IoT (CRIoT) networks. The effect of security attacks can be reduced by implementing defensive approaches. However, such solutions come at the expense of degrading spectrum efficiency and consuming more network resources. In this paper, we investigate the spectrum sharing and access problem in a multidevice single‐transceiver CRIoT network with time‐critical applications under jamming attacks. Our main goal is to maximize the number of simultaneously served IoT devices over all available idle channels while ensuring delay requirement, hardware, link quality, security attacks, and spectrum utilization constraints. This problem is formulated as a total unimodular binary linear programming, which is shown to be solvable in polynomial time. Unlike most of previous security‐aware channel assignment solutions that conduct the channel assignment sequentially, our solution simultaneously provides secured distributed channel‐assignment decisions for multiple CRIoT links (batching method). Batching can be realized through an admission control stage for CR IoT devices to announce their control packets. Simulation results reveal that our solution significantly improves network performance compared to previous security‐aware schemes.

The rapid proliferation of Internet of Things (IoT) devices has ushered in a new era of connectivity and data exchange, revolutionizing various industries. However, the inherent vulnerabilities in traditional centralized transaction systems pose significant security challenges, particularly when dealing with sensitive data generated by IoT devices. This paper introduces an ICAA (Integrity Consensus Authorization Algorithm) for securing transaction records over the IoT network by leveraging Decentralized Distributed Ledger Technology (DDL), integrating the PICA (Proof-of-Integrity Consensus Algorithm) and CTAP (Context-Aware Transaction Authorization Protocol). The proposed system addresses the limitations of centralized architectures by employing a decentralized ledger, ensuring transparency, immutability, and tamper-resistant transaction records. The Proof-of-Integrity Consensus Algorithm enhances the security of the network by validating and confirming transactions based on the integrity of the data stored in the distributed ledger. This consensus mechanism minimizes the risk of fraudulent activities and unauthorized modifications, making it well-suited for the dynamic and distributed nature of IoT environments. Furthermore, the integration of the Context-Aware Transaction Authorization Protocol enhances the adaptability of the system to the diverse contexts in which IoT devices operate. The synergy between the Proof-of-Integrity Consensus Algorithm and the Context-Aware Transaction Authorization Protocol creates a comprehensive and secure framework for managing transaction records in IoT networks. . The proposed HGGC is 5.026% better than the ECMQV-MAC, 0.4215% better than QKD, and 0.0843% better than OTP in the nodes 200. The proposed model contributes to the establishment of a trustworthy and resilient infrastructure for the IoT, laying the foundation for secure and transparent transactions in the connected world.

Extensive internet of things (IoT) devices being in-fected by malware are an increasingly important viable objective in IoT cyberattacks e.g., botnet, virus, trojan, etc. The botnets got leverage from unsecured IoT devices (e.g., CCTV, Raspberry Pi, Arduino Uno, ESP8266, etc) that operates by using the Internet traffic. In recent year, the high-profile IoT device’s vendor and the researcher from all over universities are exploring the robustness of IoT devices against botnet attacks. This research uses a deep learning approach to prevent botnet attacks on IoT networks. The deep residual one-dimensional CNN (1DCNN) model as the proposed method is used for botnet traffic detection. Two algorithms are provided: data processing for the N-BaIoT dataset and IoT botnet detection training and testing. For data processing, training, and testing, the datasets were evaluated, and the model was optimized with different optimizers. This research used RMS Prop, ADaDelta, AdaGrad, AdaMax, and Adam as optimizers and the CNN was compared with LSTM, CNN with RNN, and Deep residual 1DCNN, respectively. The results showed that Deep Residual 1DCNN with Adam has the highest training accuracy of 88.67%, 88.67% for validation accuracy, and 88.53%for test accuracy.

The Internet of Things (IoT) devices is able to communicate with another IoT devices in heterogeneous environments. They are also able to create a network by their own using wireless capabilities without a centralized approach. This network is called wireless mobile ad hoc network (MANET). The MANET facilitate IoT devices to communicate with each other in an infrastructure less network of the Internet of Things environment. The IoT devices can dynamically join, create connection and exchange information among them. The role of cloud in this framework is to store and process the data by IoT devices. The communication Security has been raised as one of the most critical issues of cloud computing where resolving such an issue would result in a constant growth in the use and popularity of cloud. Our purpose of this study is to create a framework for providing the communication in an integrated framework of Cloud and MANET among IoT devices. Our main contribution links a new study that integrates cloud computing to the MANET and provides communication to the internet of things. This study can be used in the framework of the Internet of Things in future.

The need for secure Internet of Things (IoT) devices is growing as IoT\ndevices are becoming more integrated into vital networks. Many systems rely on\nthese devices to remain available and provide reliable service. Denial of\nservice attacks against IoT devices are a real threat due to the fact these low\npower devices are very susceptible to denial-of-service attacks. Machine\nlearning enabled network intrusion detection systems are effective at\nidentifying new threats, but they require a large amount of data to work well.\nThere are many network traffic data sets but very few that focus on IoT network\ntraffic. Within the IoT network data sets there is a lack of CoAP denial of\nservice data. We propose a novel data set covering this gap. We develop a new\ndata set by collecting network traffic from real CoAP denial of service attacks\nand compare the data on multiple different machine learning classifiers. We\nshow that the data set is effective on many classifiers.\n

Edge computing provides cloud services at the edge of the network for Internet of Things (IoT) devices. It aims to address low latency of the network and alleviates data processing of the cloud. This “cloud-edge-device” paradigm brings convenience as well as challenges for location-privacy protection of the IoT. In the edge computing environment, the fixed edge equipment supplies computing services for adjacent IoT devices. Therefore, edge computing suffers location leakage as the connection and authentication records imply the location of IoT devices. This article focuses on the location awareness in the edge computing environment. We adopt the “deniability” of authentication to prevent location leakage when IoT devices connect to the edge nodes. In our solution, an efficient deniable authentication based on a two-user ring signature is constructed. The robustness of authentication makes the fixed edge equipment accept the legal end devices. Besides, the deniability of authentication cannot convince any third party that the fact of this authentication occurred as communication transcript is no longer an evidence for this connection. Therefore, it handles the inherent location risk in edge computing. Compared to efficient deniable authentications, our protocol saves 10.728% and 14.696% computational cost, respectively.

The Internet of Things (IoT) has had a considerable influence on our daily lives by enabling enhanced connection of devices, systems, and services that extends beyond machine-to-machine interactions and encompasses a wide range of protocols, domains, and applications. However, despite privacy concerns shown by IoT users, little has been done to reduce and protect individual information exposure. It is extremely difficult to mitigate IoT devices from reidentification threats which is why it is still a major challenge for IoT users to securely protect their information. The trust controls how we regulate privacy in our IoT platforms in the same way that it governs personal relationships. As IoT devices become increasingly linked, more data is shared across individuals, businesses, governments, and ecosystems. Technologies, sensors, machines, data, and cloud connections all rely largely on trust relationships that have been formed. With the rapid growth of additional types of IoT devices that are being introduced, it, therefore, expands privacy concerns and is difficult to develop trust with an IoT system or device without the option to regulate information privacy settings. Privacy has always been a barrier for many devices as they race for the early adoption of IoT technologies. Several Internet of Things devices or systems will continue to pose privacy threats. As a result, the main objective of this study was to examine the individual understanding of privacy and to promote information privacy protection awareness not only to IoT users but also to organizations that use IoT devices or platforms to run their day-to-day business operations. Furthermore, the objective extends to compare user knowledge and concerns about IoT privacy, as well as to identify any common attitudes and variances. However, in terms of enhancing individuals’ knowledge, an artifact was developed to educate and enhance information privacy awareness among IoT users. A pre- and postquestionnaire was generated to test and validate user knowledge regarding information privacy protection in IoT. The study was conducted using a quantitative research method. Findings indicate that IoT users’ awareness of information privacy protection turned out to be average, suggesting a need for education and awareness. Several participants stated that information privacy protection awareness is required within the community to educate, raise awareness, eliminate human error, and enable individuals to be conscious of their privacy when surfing the Internet.

Seeing is not always believing: Insights on IoT manufacturing from firmware composition analysis and vendor survey

With the advancement in science and technology, the demand for electronic Internet of Things (IoT) devices has increased to store and process digital data. With the advancement in IoT technology, we are more reliant on IoT devices to perform our regular tasks. IoT Forensics deals with the investigation of IoT devices such as smartphones, tablets, smart watches, or any device which is connected to the Internet. The data on these devices can still be retrieved via IoT forensics even if they are destroyed, resold, or misplaced. Before discarding any IoT device, we must consider how to secure the data stored on them. We are then going to discuss the several types of personal data that could be retrieved from discarded IoT devices. Finally, we are going to discuss the protection measures for the safe disposal of IoT devices.

With the advancement of 5G mobile telecommunication, various IoT (Internet of Things) devices communicate massive amounts of data by being connected to wireless networks. Since this wireless communication is vulnerable to hackers via data leakage during communication, the transmitted data should be encrypted through block ciphers to protect the data during communication. In addition, in order to encrypt the massive amounts of data securely, it is essential to apply one of secure mode of operation. Among them, CTR (CounTeR) mode is the most widely used in industrial applications. However, these IoT devices have limited resources of computing and memory compared to typical computers, so that it is challenging to process cryptographic algorithms that have computation-intensive tasks in IoT devices at high speed. Thus, it is required that cryptographic algorithms are optimized in IoT devices. In other words, optimizing cryptographic operations on these IoT devices is not only basic but also an essential effort in order to build secure IoT-based service systems. For efficient encryption on IoT devices, even though several ARX (Add-Rotate-XOR)-based ciphers have been proposed, it still necessary to improve the performance of encryption for smooth and secure IoT services. In this article, we propose the first parallel implementations of CTR mode of ARX-based ciphers: LEA (Lightweight Encryption Algorithm), HIGHT (high security and light weight), and revised CHAM on the ARMv8 platform, a popular microcontroller in various IoT applications. For the parallel implementation, we propose an efficient data parallelism technique and register scheduling, which maximizes the usage of vector registers. Through proposed techniques, we process the maximum amount of encryption simultaneously by utilizing all vector registers. Namely, in the case of HIGHT and revised CHAM-64/128 (resp. LEA, revised CHAM-128/128, and CHAM-128/256), we can execute 48 (resp. 24) encryptions simultaneously. In addition, we optimize the process of CTR mode by pre-computing and using the intermediate value of some initial rounds by utilizing the property that the nonce part of CTR mode input is fixed during encryptions. Through the pre-computation table, CTR mode is optimized up until round 4 in LEA, round 5 in HIGHT, and round 7 in revised CHAM. With the proposed parallel processing technique, our software provides 3.09%, 5.26%, and 9.52% of improved performance in LEA, HIGHT, and revised CHAM-64/128, respectively, compared to the existing parallel works in ARM-based MCU. Furthermore, with the proposed CTR mode optimization technique, our software provides the most improved performance with 8.76%, 8.62%, and 15.87% in LEA-CTR, HIGHT-CTR, and revised CHAM-CTR, respectively. This work is the fastest implementation of CTR mode on ARMv8 architecture to the best of our knowledge.

In the modern security-conscious world, Deep Packet Inspection (DPI) proxies are increasingly often used on industrial and enterprise networks to perform TLS unwrapping on all outbound connections. However, enabling TLS unwrapping requires local devices to have the DPI proxy Certificate Authority certificates installed. While for conventional computing devices this is addressed via enterprise management, it's a difficult problem for Internet of Things (IoT) devices which are generally not under enterprise management, and may not even be capable of it due to their resource-constrained nature. Thus, for typical IoT devices, being installed on a network with DPI requires either manual device configuration or custom DPI proxy configuration, both of which solutions have significant shortcomings. This poses a serious challenge to the deployment of IoT devices on DPI-enabled intranets. The authors propose a solution to this problem: a method of installing on IoT devices the CA certificates for DPI proxy CAs, as well as other security configuration (security bootstrapping). The proposed solution respects the DPI policies, while allowing the commissioning of IoT and IIoT devices without the need for additional manual configuration either at device scope or at network scope. This is accomplished by performing the bootstrap operation over unsecured connection, and downloading certificates using TLS validation at application level. The resulting solution is light-weight and secure, yet does not require validation of the DPI proxy's CA certificates in order to perform the security bootstrapping, thus avoiding the chicken-and-egg problem inherent in using TLS on DPI-enabled intranets.

The number of Internet of Things (IoT) devices has increased recently and will increase further in the future. IoT devices are vulnerable, so vendors update and distribute firmware. At the time of firmware distribution, a huge number of IoT devices may connect to the firmware server and excessive network traffic may occur. Consequently, a method using a peer-to-peer file sharing system and a blockchain has been proposed. One study proposed an update scheme considering incentives for distributors to help with updating. However, this method requires the IoT devices, which have limited processing power, to decrypt encrypted files, and the distribution nodes to pay the transaction cost. This paper proposes a firmware distribution method that provides incentives for distributors to help with distribution to reduce the gas costs, using a smart contract and access control based on update records. The additional computations performed by IoT devices and distributors key management were reduced compared to those in previous studies by using access control instead of encryption. Further, the proposed approach was implemented and evaluated using a Raspberry Pi and laptop. The evaluation demonstrated that the gas cost per update was successfully lowered compared to the costs in previous studies.

As location-aware IoT (Internet of Things) devices intend to spread across almost every application, IoT devices are going to require different GNSS (Global Navigation Satellite System) receiver design requirements. To deliver on IoT opportunities, system architects and designers need to look carefully at every aspect of system design and architecture to be able to enable the full potential of the IoT era. IoT devices are equipped with different connectivity sensors that can provide a reliable integrated location-awareness solution. IoT devices are mainly relying on GNSS chip to deliver a service when no other RF signal is available. Hence, GNSS chip is expected to maintain a robust and reliable performance even in harsh environment. The harsh environment includes multipath environment, NLOS (Non-Line of Sight) GNSS signal reception, weak GNSS signal power reception, superimposed motion (e.g., arm swing, floating platform fluctuation …etc.), operation under freezing temperature, and interference. The targeted low-cost system design along with the expected harsh operational environment derived us to face exceptional GNSS signal reception condition. This paper discusses lessons learned, and challenges faced signal acquisition, reacquisition, and tracking for several IoT applications. Different operational modes are also explored to accommodate various use cases scenarios for several IoT applications. These different power consumption operational modes allow the GNSS chip to achieve an Ultra-low power consumption which indeed required for IoT applications. This paper provides an overview about the addressed GNSS chip fabricated in a 28nm FD-SOI process. We demonstrate a system performance and power consumption comparison of this chip along with other state-of-the-art GNSS chip. We compare the positioning performance for this device alongside another state-of-the-art GNSS modules and Novatel’s tightly coupled GNSS/INS (Inertial Navigation System) reference solution at numerous scenarios ranging from walking, running, and driving at several sites under different environment.

The ability to deploy such systems throughout a region, or perhaps a nation, will increase as IoT infrastructure develops. Although Internet of Things (IoT) devices are capable of offering intelligent services, the massive amounts of data they gather and analyze pose a severe security threat. Researchers have spent a lot of work building sophisticated NIDS to prevent the exploitation of IoT data in smart applications. However, present methods may be vulnerable to attack, particularly new attacks, due to a lack of sufficient and evenly distributed attack data used to train the detection strategy. This study introduces a original hierarchical adversarial attack (HAA) generation strategy, which in turn targets the convolutional neural network-based intrusion detection in IoT devices with a limited budget, and therefore realizes the level-aware black-box adversarial attack approach. To generate adversarial instances with little disturbance, an intelligent approach is developed that relies on a saliency map methodology. To do this, a shadow CNN framework has been constructed. Using a random walk having restart based hierarchical node selection approach, a subset of the targeted IoT network's nodes with the lowest structural strength are selected. The proposed HAA generation technique is evaluated in comparison to three reference methods using the publicly available data set UNSW-SOSR2019. In a comparison of the two most sophisticated convolutional neural network (CNN) designs, GCN and JK-Net, it was shown that the classification accuracy for NIDS in IoT settings may be reduced by more than 30%.