Computational analysis of dispersive and nonlinear 2D materials by using a GS-FDTD method

The isolation of graphene has sparked an unprecedented world wide research activity on the topic of two-dimensional (2D) materials. However, even though graphene has a high potential for various applications, its metallic character is a significant limitation for a large variety of electron devices, starting with the conventional field effect transistor. This limitation could be overcome in the near future by the use of layered van der Waals crystals such as black phosphorus (i.e., phosphorene, which is one to few layers of black phosphorus) and also by other semiconducting 2D materials such as transition metal dichalcogenides (TMDCs) of general formula MX2, where M is the metal and X the chalcogen (S, Se and Te). For instance, phosphorene exhibits a direct band gap varying between ~ 0.3 eV for bulk crystals to ~ 2 eV for a monolayer. In layered TMDC structures, each layer typically comprises 3 atomic planes (corresponding to a thickness below 8 Å), and consists of an hexagonally-organized atomic layer of metal atoms sandwiched between two planes of chalcogen atoms, also in hexagonal configurations. M–X bonds inside each layer are covalent; however, the sandwiching chalcogen layers are linked by weak van der Waals bonds, so that a bulk crystal is easy to cleave along the chalcogen planes. As with phosphorene, most semiconducting TMDC materials also see their band gap increasing as thickness decreases and they switch from indirect to direct band gap for a monolayer. To date, the most studied semiconductor TMDCs are MoS2 and WS2. Because they are atomically thin, 2D materials are particularly well suited for flexible electronics applications. After a brief description of the major features of phosphorene and TMDCs (crystal structures, relevant electronic properties as a function of thickness …), the talk will highlight recent results concerning field effect transistor characteristics. In particular, carrier mobility values as high as 5000 cm2/Vs have been measured in phosphorene films. Since local substitutional-type doping cannot be used in 2D materials, there is a general contacting problem (Schottky barrier formation), which is of paramount importance for device applications. In particular, two types of contacts can be formed: the top contact and the edge contact, which behave differently. Generally speaking, the semiconductor thickness is much smaller than the depletion length at the contact, which is an intriguing and novel situation. In the second part of the talk, various synthesis methods will be presented and discussed, particularly in view of their possible use in the field of large area electronics. For most devices fabricated so far, the 2D layers were obtained by exfoliation of bulk crystals. However, recent progress in synthesis include molecular beam epitaxy, controlled chemical vapour deposition and vapour phase transport. Those various approaches will be discussed, as well as the newly-introduced atomic layer deposition (ALD) process. As most 2D materials are grown on a separate substrate, the transfer problem will be highlighted, particularly concerning phosphorene which is highly hygroscopic, and sensitive to the presence of light. The presentation will be concluded by some perspectives concerning the industrialization of 2D materials.

Direct liquid-phase exfoliation of layered materials by means of ultrasound, shear forces or electrochemical intercalation holds enormous promise as a convenient, cost-effective approach to the mass production of two-dimensional (2D) materials, particularly in the form of colloidal suspensions of high quality and micrometer- and submicrometer-sized flakes. Of special relevance due to environmental and practical reasons is the production of 2D materials in aqueous medium, which generally requires the use of certain additives (surfactants and other types of dispersants) to assist in the exfoliation and colloidal stabilization processes. In this context, biomolecules have received, in recent years, increasing attention as dispersants for 2D materials, as they provide a number of advantages over more conventional, synthetic surfactants. Here, we review research progress in the use of biomolecules as exfoliating and dispersing agents for the production of 2D materials. Although most efforts in this area have focused on graphene, significant advances have also been reported with transition metal dichalcogenides (MoS2, WS2, etc.) or hexagonal boron nitride. Particular emphasis is placed on the specific merits of different types of biomolecules, including proteins and peptides, nucleotides and nucleic acids (RNA, DNA), polysaccharides, plant extracts and bile salts, on their role as efficient colloidal dispersants of 2D materials, as well as on the potential applications that have been explored for such biomolecule-exfoliated materials. These applications are wide-ranging and encompass the fields of biomedicine (photothermal and photodynamic therapy, bioimaging, biosensing, etc.), energy storage (Li- and Na-ion batteries), catalysis (e.g., catalyst supports for the oxygen reduction reaction or electrocatalysts for the hydrogen evolution reaction), or composite materials. As an incipient area of research, a number of knowledge gaps, unresolved issues and novel future directions remain to be addressed for biomolecule-exfoliated 2D materials, which will be discussed in the last part of this review.

Stretchable photodetectors based on 2D materials: materials synthesis, fabrications and applications

The layered two-dimensional (2D) materials, e.g., the well-known graphene, transition metal dichalcogenides, and topological insulators, have attracted great interest of researchers from fundamental research as well as industries owing to their intriguing properties in a number of aspects. In practical applications, the efficient modification of the features of 2D materials is compelling and essential to achieve desired functionalities. Ion implantation has been successfully applied to synthesize graphene. The most exotic advantage of ion beam technology is that it offers distinct options of energetic beams, which has recently shown the unique capability to modify and tailor the properties of versatile 2D materials. To name a few, the energetic ion beams could implement the surface morphology or layer-to-layer structural engineering of 2D materials. At the microcosmic level, the introduction of ion beam induced defects and intentional doping of specific ions are the basis of tailoring properties of 2D materials. By manipulating the parameters of ion beams (energies, species, fluences, incident angles, etc.), the modified 2D materials may possess novel properties, which are unprecedented in pristine ones. Promising applications based on these 2D materials with ion beam tailored features have been realized in a broad range of fields. In this work, we systematically review the latest research progress on the deployed techniques and property modifications of graphene and other 2D materials under the treatment of various ion beams. A few selected applications are presented to indicate the practical potentials of ion beam modified 2D materials in distinct areas. Perspectives on future developments are also provided by focusing on several promising topics.

Towards controlled synthesis of 2D crystals by chemical vapor deposition (CVD)

The fascinating two-dimensional (2D) materials are being unconsciously applied in various fields from science to engineering, which is benefited from the glamorous physical and chemical properties of mechanics, optics, electronics, and magnetism. The representative 2D thermoelectric/piezoelectric materials can directly convert thermal/mechanical energy into electrical energy, which can resolve the energy issues and avoid further environmental deterioration. The thermoelectric or piezoelectric properties of various 2D materials, such as graphene, hexagonal boron nitride, black phosphorus, transition metal dichalcogenides (TMDs), arsenene, metal carbides and nitrides (MXenes), and so on, have been investigated in detail. Although tremendous progress has been achieved in the past few years, these properties still need to be improved for their practical application by designing new 2D materials, strain engineering, chemical functionalization, etc. In addition to this, in 2D materials, there are many other novel physical properties, such as magnetism, topology, valley, and so on. The combination of thermoelectricity/piezoelectricity with other unique properties may lead to novel device applications or scientific breakthroughs in new physics. Overall, the emergence of 2D thermoelectric and piezoelectric materials has expanded energy conversion research dramatically. By combing this new device concept with the novel 2D materials, original devices should have potential applications in energy harvesting.

Two-dimensional (2D) materials, such as graphene and transition-metal dichalcogenide monolayers, have unique properties that are distinctly different from those of their bulk counterparts, and hopefully possess a wide range of applications in 2D semiconductor device. Structural defects are known to have profound influences on the properties of crystalline materials; thus, correlating the defect structure with local properties in 2D material is of fundamental importance. However, electron microscopy studies of 2D materials on an atomic scale have become a challenge as most of these materials are susceptible to electron beam irradiation damage under high voltage and high dose experimental conditions. The development of low voltage aberration-corrected scanning transmission electron microscopy (STEM) has made it possible to study 2D materials at a single atom level without damaging their intrinsic structures. In addition, controllable structural modification by using electron beam becomes feasible by controlling the electron beam-sample interaction. New nanostructures can be created and novel 2D materials can be fabricated in-situ by using this approach. In this article, we review some of our recent studies of graphene and transition-metal dichalcogenides to showcase the applications of low voltage aberration corrected STEM in 2D material research.

Two-dimensional (2D) materials are crystals with one to a few layers of atoms and are being used in many fields such as optical modulator, photodetector, optical switch, and ultrafast lasers. Their exceptional optoelectronic and nonlinear optical properties make them as a suitable saturable absorber for laser cavities. This review focuses on the recent progress in ultrafast laser use 2D materials as a saturable absorber. 2D materials traditionally include graphene, topological insulators, transition metal dichalcogenides, as well as new materials such as black phosphorus, bismuthene, antimonene, and MXene. Material characteristics, fabrication techniques, and nonlinear properties are also introduced. Finally, future perspectives of ultrafast lasers based on 2D materials are also addressed.

A systematic review on 2D materials for volatile organic compound sensing

Environmental resilience with 2D materials: A futuristic perspective

In the last decade, the rise of two-dimensional (2D) materials has attracted a tremendous amount of interest for the entire field of photonics and opto-electronics. The mechanism of light–matter interaction in 2D materials challenges the knowledge of materials physics, which drives the rapid development of materials synthesis and device applications. 2D materials coupled with plasmonic effects show impressive optical characteristics, involving efficient charge transfer, plasmonic hot electrons doping, enhanced light-emitting, and ultrasensitive photodetection. Here, we briefly review the recent remarkable progress of 2D materials, mainly on graphene and transition metal dichalcogenides, focusing on their tunable optical properties and improved opto-electronic devices with plasmonic effects. The mechanism of plasmon enhanced light–matter interaction in 2D materials is elaborated in detail, and the state-of-the-art of device applications is comprehensively described. In the future, the field of 2D materials holds great promise as an important platform for materials science and opto-electronic engineering, enabling an emerging interdisciplinary research field spanning from clean energy to information technology.

Two-dimensional (2D) materials such as graphene, transition metal dichalcogenides and phosphorene have emerged as brand new photonic materials with huge potential in a variety of optical applications in recent years, due to their unique properties and multiple functions. Owning to the significantly increased surface to volume ratio in the atomic thin layered structure, the interactions between 2D materials with light become remarkably strong in either elastic or inelastic interactions. Most of previous studies were focused on the inelastic interactions between 2D materials with light, namely Raman and photoluminescence properties. However, we found the elastic interactions between them and light are also very attractive. Based on the properties discovered, we demonstrated several optical applications, such as atomically thin optical lenses and gratings. On the other hand, we found the inelastic interactions with light in the 2D limitation affected a lot by the external environment, which could serve as a unique method to control the working status of the optical devices to meet multiple application needs. Several progresses were demonstrated such as control of excitons and trions in few-layer MoS2 via the co-modulations by both temperature and electric field and the defect engineering by oxygen plasma etching to stimulate new photon emission.

Cost-effective, rapid, and accurate virus detection technologies play key roles in reducing viral transmission. Prompt and accurate virus detection enables timely treatment and effective quarantine of virus carrier, and therefore effectively reduces the possibility of large-scale spread. However, conventional virus detection techniques often suffer from slow response, high cost or sophisticated procedures. Recently, two-dimensional (2D) materials have been used as promising sensing platforms for the high-performance detection of a variety of chemical and biological substances. The unique properties of 2D materials, such as large specific area, active surface interaction with biomolecules and facile surface functionalization, provide advantages in developing novel virus detection technologies with fast response and high sensitivity. Furthermore, 2D materials possess versatile and tunable electronic, electrochemical and optical properties, making them ideal platforms to demonstrate conceptual sensing techniques and explore complex sensing mechanisms in next-generation biosensors. In this review, we first briefly summarize the virus detection techniques with an emphasis on the current efforts in fighting again COVID-19. Then, we introduce the preparation methods and properties of 2D materials utilized in biosensors, including graphene, transition metal dichalcogenides (TMDs) and other 2D materials. Furthermore, we discuss the working principles of various virus detection technologies based on emerging 2D materials, such as field-effect transistor-based virus detection, electrochemical virus detection, optical virus detection and other virus detection techniques. Then, we elaborate on the essential works in 2D material-based high-performance virus detection. Finally, our perspective on the challenges and future research direction in this field is discussed.

Two-dimensional (2D) materials have captured the attention of the scientific community due to the wide range of unique properties at nanometer-scale thicknesses. While significant exploratory research in 2D materials has been achieved, the understanding of 2D electronic transport and carrier dynamics remains in a nascent stage. Furthermore, because prior review articles have provided general overviews of 2D materials or specifically focused on charge transport in graphene, here we instead highlight charge transport mechanisms in post-graphene 2D materials, with particular emphasis on transition metal dichalcogenides and black phosphorus. For these systems, we delineate the intricacies of electronic transport, including band structure control with thickness and external fields, valley polarization, scattering mechanisms, electrical contacts, and doping. In addition, electronic interactions between 2D materials are considered in the form of van der Waals heterojunctions and composite films. This review concludes with a perspective on the most promising future directions in this fast-evolving field.

Multifunctional polymer composite gels have attracted attention because of their high thermal stability, conductivity, mechanical properties, and fast optical response. To enable the simultaneous incorporation of all these different functions into composite gels, the best doping material alternatives are two-dimensional (2D) materials, especially transition metal dichalcogenides (TMD), which have been used in so many applications recently, such as energy storage units, opto-electronic devices and catalysis. They have the capacity to regulate optical, electronic and mechanical properties of basic molecular hydrogels when incorporated into them. In this study, 2D materials (WS2, MoS2 and MoSe2)-doped polyacrylamide (PAAm) gels were prepared via the free radical crosslinking copolymerization technique at room temperature. The gelation process and amount of the gels were investigated depending on the optical properties and band gap energies. Band gap energies of composite gels containing different amounts of TMD were calculated and found to be in the range of 2.48–2.84 eV, which is the characteristic band gap energy range of promising semiconductors. Our results revealed that the microgel growth mechanism and gel point of PAAm composite incorporated with 2D materials can be significantly tailored by the amount of 2D materials. Furthermore, tunable band gap energies of these composite gels are crucial for many applications such as biosensors, cartilage repair, drug delivery, tissue regeneration, wound dressing. Therefore, our study will contribute to the understanding of the correlation between the optical and electronic properties of such composite gels and will help to increase the usage areas so as to obtain multifunctional composite gels.