Control Design of Elementary Hybrid Petri Nets via Model Predictive Control

Multi-vector model predictive control of permanent magnet synchronous motor can effectively overcome the shortcomings of conventional single-vector model predictive control such as large motor current ripples and limited control accuracy, but its control performance is more susceptible to the influence of motor parameter perturbation. To improve the robustness of the multi-vector predictive control algorithm under the motor parameter perturbation, a novel nonparametric three-vector model predictive current control method for permanent magnet synchronous motors is proposed in this paper. Through constructing an ultra-local predictive current model based on the input and output signals of the permanent magnet synchronous motor, the influence of motor parameter perturbation on current prediction is avoided, and a disturbance observer is designed to estimate the non-modeled and perturbed parts of the ultra-local model. In addition, the direct calculation method of vector duty cycles based on current error is introduced to suppress the influence of motor parameter uncertainty on the duty cycle calculation link, which further improves the system robustness. Finally, simulations and experiments of the proposed method are demonstrated to compare with the conventional parametric three-vector model predictive current control, and the results show that the proposed control strategy can effectively suppress the disturbances caused by the motor parameters and ensure the steady-state performance during motor operation.

The paradigm of continuous control using internal models has advanced understanding of human motor control. However, this paradigm ignores some aspects of human control, including intermittent feedback, serial ballistic control, triggered responses and refractory periods. It is shown that event-driven intermittent control provides a framework to explain the behaviour of the human operator under a wider range of conditions than continuous control. Continuous control is included as a special case, but sampling, system matched hold, an intermittent predictor and an event trigger allow serial open-loop trajectories using intermittent feedback. The implementation here may be described as "continuous observation, intermittent action". Beyond explaining unimodal regulation distributions in common with continuous control, these features naturally explain refractoriness and bimodal stabilisation distributions observed in double stimulus tracking experiments and quiet standing, respectively. Moreover, given that human control systems contain significant time delays, a biological-cybernetic rationale favours intermittent over continuous control: intermittent predictive control is computationally less demanding than continuous predictive control. A standard continuous-time predictive control model of the human operator is used as the underlying design method for an event-driven intermittent controller. It is shown that when event thresholds are small and sampling is regular, the intermittent controller can masquerade as the underlying continuous-time controller and thus, under these conditions, the continuous-time and intermittent controller cannot be distinguished. This explains why the intermittent control hypothesis is consistent with the continuous control hypothesis for certain experimental conditions.

Model predictive control (MPC) presents important advantages in the control of the power converter and drives such as, fast dynamic response and capability to include nonlinear constrains. These have positioned MPC as a powerful and realistic control strategy, however, it also has disadvantages such as variable switching frequency and parameter sensitivity. This paper applied a modulated model predictive speed control that guarantees a fix switching frequency and, thanks to disturbance compensation, robustness to parameters variation. The strategy is validated and compared to finite set model predictive speed control through simulation results.

Model predictive control (MPC) as a nonlinear control method, is being studied for a wide variety of power electronics applications targeting various power ranges. The fast dynamic response, robustness under different load conditions, multi-objective control, and simplicity of implementation are the main features of MPC. However, the implementation of finite control set MPC (FCS-MPC) or direct MPC in its basic form for multilevel converters (MLCs) demonstrates the inability to generate the staircase multilevel output voltage waveform in a voltage sourced inverter (VSI) application. Adding a reference evaluation block to the basic FCS-MPC method can significantly improve its multilevel voltage generation capability. In this paper, an enhanced model predictive nearest level control (EMP-NLC) is proposed and implemented on a 5-Level flying capacitor multilevel converter (FCMC). The proposed method is simulated under different load conditions, while a comparison against existing MPC techniques is also presented. Experimental results verified the efficacy of the proposed controller.

Fifty-seven per cent of all water supply systems in the Netherlands are controlled by model predictive flow control; the other 43% are controlled by conventional level-based flow control. The differences between conventional level-based flow control and model predictive control were investigated in experiments at five full-scale water supply systems in the first half of 2011. Quality parameters of the drinking water and energy consumption of the treatment and distribution processes were measured and analysed. The experiments showed that the turbidity values are 12–28% lower, and particle volume values 12–42% lower for the systems which are controlled by model predictive flow control. The overall energy consumption of water supply systems controlled by predictive flow control is 1.0–5.3% lower than conventional level-based flow controlled systems, and the overall energy costs are 1.7–7.4% lower.

Model predictive control (MPC) is an efficient and growing approach to power converter control. This paper proposes an improved and simplified model predictive current control (MPCC) technique for a four-level nested neutral point clamped (4L-NNPC) converter. Conventional MPCC exhibits better performances as compared to the conventional linear control system such as fast dynamic response, consideration of the system constraints, and nonlinearities. However, the application of the conventional model predictive current control (MPCC) approach on complex systems provokes a significant number of calculations, which is the main hurdle to its practical implementation. To fix this flaw, this paper proposes an effective algorithm to shorten the execution time of the conventional MPCC. In this proposed technique, 216 current predictions of the conventional MPCC are skipped and converted into one required voltage vector (RVV) prediction. With this equivalent reference voltage transformation, the calculation burden of MPCC is significantly reduced, while the output performance is not influenced. The results of the simplified MPCC for the 4L-NNPC converter are analyzed and compared with the conventional MPCC. The computational time is reduced by 19.56% using the simplified MPCC, while keeping an approximately similar error of output currents. The switching frequency and total harmonic distortion (THD) of the proposed method are reduced by 8.16% and 0.07%, respectively, as compared to the conventional technique. These results demonstrate the fact that that the performance of a conventional MPCC is enhanced with the proposed MPCC. The proposed algorithm can be applied to several inverter topologies.

Nowadays, a model predictive control has gained a lot of attractions for power converter. To overcome the defects of the conventional model predictive control and achieve better performance, this article presents a multivector model predictive power control (MV-MPPC) with low computational burden for the grid-tied quasi-Z-source inverter (qZSI). Compared with the conventional model predictive power control (MPPC) that adopts only one vector in one control period, the proposed MV-MPPC applies several vectors including two active vectors, one null vector, and one shoot-through (ST) vector to fulfill the expected performance for the grid-tied qZSI. By calculating the optimal duty ratios of the ST vector, the inductor current ripple can be greatly reduced. To eliminate the weighting factor, a modified sliding-mode control method for simultaneously controlling the capacitor voltage and the inductor current to their setting points is proposed. Furthermore, a quick and effective optimal sector selection method is given, which chooses the optimal sector through a look-up table instead of a bunch of complex calculations. Hence, the computational burden of the proposed MV-MPPC is decreased with significance. Both simulation and experimental results are shown to validate the effectiveness and the advantages of the proposed method.

The research object of this paper is single-phase PWM rectifier, the purpose is to reduce the total harmonic distortion (THD) of the grid-side current. A model predictive current control (MPCC) with fixed switching frequency and dead-time compensation is proposed. First, a combination of an effective vector and two zero vectors is used to fix the switching frequency, and a current prediction equation based on the effective vector’s optimal action time is derived. The optimal action time is resolved from the cost function. Furthermore, in order to perfect the established prediction model and suppress the current waveform distortion as a consequence of the dead-time effect, the dead-time’s influence on the switching vector’s action time is analyzed, and the current prediction equation is revised. According to the experimental results, the conclusion is that, firstly, compared with finite-control-set model predictive control, proportional-integral-based instantaneous current control (PI-ICC) scheme and model predictive direct power control (MP-DPC), the proposed MPCC has the lowest current THD. In addition, the proposed MPCC has a shorter execution time than MP-DPC and has fewer adjusted parameters than PI-ICC. In addition, the dead-time compensation scheme successfully suppresses the zero-current clamping effects, and reduce the current THD.

In power system automatic generation control, the existence of the generation rate constraints (GRC) and the valve limit on the governor can greatly influence the dynamic responses of the power system. Model predictive control is a popular control strategy which takes systematic account of process input, state and output constraints, thereby is employed to load frequency control to cope with the GRC. The valve limit on the governor is modeled by a fuzzy model so that the local predictive controllers are incorporated into the nonlinear control system. The proposed methodology is tested with an interconnected power system. Simulation results demonstrate the effectiveness of the proposed nonlinear constraint predictive control algorithm.

This paper presents a model predictive voltage control method for single-inductor multiple-output (SIMO) DC/DC converters operating in the continuous conduction mode (CCM). The state-space model for a SIMO DC/DC converter system is formulated and a Model Predictive Control (MPC) strategy, which has the capability to track the reference voltage automatically and reduce the impact of cross regulation problem, is proposed to regulate the system. Considering that the switches in the converter only have ON/OFF modes, the quadratic programming algorithm is employed to obtain the MPC's solution. Simulation studies are conducted in MATLAB/Simulink to verify the performance of the proposed method.

The need for cost-effective fuel economy improvements has driven the introduction of automatic transmissions with an increasing number of gear ratios. Incorporation of interlocking dog clutches in these transmissions decreases package space and increases efficiency, as compared to conventional dry or wet clutches. Unlike friction based clutches, interlocking dog clutches require very precise rotational speed matching prior to engagement. Precise engine speed control is therefore critical to maintaining high shift quality. This research focuses on controlling the engine speed during a gearshift period by manipulating throttle position and combustion phasing. Model predictive control (MPC) is advantageous in this application since the speed profile of a future prediction horizon is known with relatively high confidence. The MPC can find the optimal control actions to achieve the designated speed target without invoking unnecessary actuator manipulation and violating hardware and combustion constraints. This research utilizes linear parameter varying (LPV) MPC to control the engine speed during the gearshift period. Combustion stability constraints are considered with a control oriented covariance of indicated mean effective pressure model (COV of IMEP). The proposed MPC engine speed controller is validated with a high-fidelity 0-dimensional engine model with crank angle resolution. Four case studies, based on simulation, investigate the impact of different MPC design parameters. They also demonstrate that the proposed MPC engine controller successfully achieves the speed reference tracking objective while considering combustion variation constraints.

The wide availability of microprocessors with much higher computational power capabilities has encouraged many researchers during the last decade to introduce the predictive control techniques to the field of power electronics and motor drives. One technique of predictive control, which is called model predictive control, is introduced in this paper and its application to control a five-phase induction motor is also presented. The mathematical formulation of both model predictive torque control and model predictive speed control algorithms are explained, which shows that the algorithms' equations are intuitive so they can be easily understood and implemented. Since a load torque estimate is needed in the predictive speed controller, an observer based on the minimal-order Gopinath's method is designed to get the load torque value. A comparison between the two techniques is carried out based on a simulation study. Also, the simulation results show the effectiveness of the predictive control in achieving a high dynamic performance control of multiphase induction motor drives.

Model Predictive Control (MPC), the dominant advanced control approach in industry over the past twenty-five years, is presented comprehensively in this unique book. With a simple, unified approach, and with attention to real-time implementation, it covers predictive control theory including the stability, feasibility, and robustness of MPC controllers. The theory of explicit MPC, where the nonlinear optimal feedback controller can be calculated efficiently, is presented in the context of linear systems with linear constraints, switched linear systems, and, more generally, linear hybrid systems. Drawing upon years of practical experience and using numerous examples and illustrative applications, the authors discuss the techniques required to design predictive control laws, including algorithms for polyhedral manipulations, mathematical and multiparametric programming and how to validate the theoretical properties and to implement predictive control policies. The most important algorithms feature in an accompanying free online MATLAB toolbox, which allows easy access to sample solutions. Predictive Control for Linear and Hybrid Systems is an ideal reference for graduate, postgraduate and advanced control practitioners interested in theory and/or implementation aspects of predictive control.

Model Predictive Control (MPC), the dominant advanced control approach in industry over the past twenty-five years, is presented comprehensively in this unique book. With a simple, unified approach, and with attention to real-time implementation, it covers predictive control theory including the stability, feasibility, and robustness of MPC controllers. The theory of explicit MPC, where the nonlinear optimal feedback controller can be calculated efficiently, is presented in the context of linear systems with linear constraints, switched linear systems, and, more generally, linear hybrid systems. Drawing upon years of practical experience and using numerous examples and illustrative applications, the authors discuss the techniques required to design predictive control laws, including algorithms for polyhedral manipulations, mathematical and multiparametric programming and how to validate the theoretical properties and to implement predictive control policies. The most important algorithms feature in an accompanying free online MATLAB toolbox, which allows easy access to sample solutions. Predictive Control for Linear and Hybrid Systems is an ideal reference for graduate, postgraduate and advanced control practitioners interested in theory and/or implementation aspects of predictive control.

Multi-power sources are included in hybrid electrical vehicles, which leads to multi-driving modes co-existing when driving the vehicle. However, the frequent driving mode switching (DMS) will probably need the engine to be started frequently, which can result in extra fuel consumption. So, avoiding unnecessary DMS should be fully considered when designing the control strategy. For solving this problem, a model predictive control (MPC) strategy integrating Markov chain driving intention identification is put forward. First, the component models of the powertrain system are established. Second, according to the real driving cycle data, a driving intention model based on the Markov chain is designed according to the real driving cycle data. Then the MPC-based control strategy aiming at reducing DMS times is proposed by integrating the cost of DMS. Finally, the proposed control strategy is contrasted with three other control strategies to verify its validity in reducing the mode switching times and improving the fuel economy.