Coordinated dynamic hybrid position/force control for multiple robot manipulators handling one constrained object

An approach to designing controllers for dynamic hybrid position/force control of robot manipulators is presented, and preliminary experimental results are given. Dynamic hybrid control is an extension of an approach proposed by M.H. Raibert and J.J. Craig (1981) to the case where the full manipulator dynamics is taken into consideration and the end-effector constraint is explicitly given by the constraint hypersurfaces. This design method consists of two steps. The first step is the linearization of the manipulator dynamics by nonlinear state feedback. Formulation of the constraint by the constraint hypersurfaces plays an essential role in establishing the linearizing law. The second step is the design of position and force controllers for the linearized model using the concept of two-degrees-of-freedom servocontroller. The merit of this servocontroller is that it can take account of both the command response and the robustness of the controllers to modeling errors and disturbances. Preliminary experiments using a SCARA robot show the validity of the approach. >

We address the problem of two robots manipulating a rigid object which moves along a constraint surface. The dynamic model of such a system is usually very complicated. However, because of the constrained motion, some degrees of freedom are lost or irrelevant to the required task. The work space is divided into two subspaces which describe the linear motion and the angular motion. Based on the fact that the two manipulators, the object, and the constraint surface form a closed chain, the dynamic couplings as well as the kinematic couplings among the system elements are exploited to get a reduced order dynamic model. Next, the control problem is addressed. When manipulating a constrained object using multiple robot manipulators, it is necessary to control the position of the object, the internal force exerted on the object by the manipulators, and the constraint force. Using the reduced order model, a controller consisting of a nonlinear feedback and servo compensators is proposed. Under a certain condition, this controller decouples the object position, the internal force and the constraint force. This controller also guarantees the asymptotic convergence of the position, the internal force, and the constraint force to their desired values. To validate our results, simulations for two three-link planar manipulators moving a constrained object are carried out. The simulation results show that the proposed controller achieves the desired asymptotic tracking. >

In 2013 the Editor of Journal of Vibration and Control and SAGE became aware of a peer review ring involving assumed and fabricated identities that appeared to centre around Peter Chen at National Pingtung University of Education, Taiwan (NPUE). SAGE and the Editor then began a complex investigation into the case during the rest of 2013 and 2014. Following an unsatisfactory response from Peter Chen, NPUE was notified. NPUE were serious in addressing the Journal and SAGE’s concerns. NPUE confirmed that the institution was investigating Peter Chen. SAGE subsequently uncovered a citation ring involving the above mentioned author and others. We regret that individual authors have compromised the academic record by perverting the peer review process and apologise to readers. On uncovering problems with peer review and citation SAGE immediately put steps in place to avoid similar vulnerability of the Journal to exploitation in the future. More information may be found at www.sagepub.co.uk/JVC_Statement_2014 . The Journal and SAGE understand from NPUE that Peter Chen has resigned his post at NPUE. The following articles are retracted because after thorough investigation evidence points towards them having at least one author or being reviewed by at least one reviewer who has been implicated in the peer review ring and/or citation ring. All authors have had an opportunity to respond to the allegations and proposed actions. OnlineFirst articles (these articles will not be published in an issue) Chen CY, Chen T-H, Chen Y-H, Yu S-E and Chung P-Y (2013) Information technology system modeling an integrated C-TAM-TPB model to the validation of ocean tidal analyses Journal of Vibration and Control Epub ahead of print 7 May 2013. doi: 10.1177/1077546312472924 Chang R-F, Chen CY, Su F-P and Lin H-C (2013) A two-step approach for broadband digital signal processing technique Journal of Vibration and Control Epub ahead of print 26 April 2013. doi: 10.1177/1077546312472925 Chen TH, Chang CJ, Yu SE, Chung PY and Liu C-K (2013) Nonlinear information analysis and system management technique: the influence of design experience and control complexity Journal of Vibration and Control Epub ahead of print 12 April 2013. doi: 10.1177/1077546312473321 Chen CY, Shih BY, Chen YH, Yu SE and Liu YC (2013) The exploration of a 3T flow model using vibrating NXT: II. Model validation Journal of Vibration and Control Epub ahead of print 10 April 2013. doi: 10.1177/1077546312470481 Chen CY, Shih BY, Chen YH, Yu SE and Liu YC (2013) The exploration of 3T flow model using vibrating NXT: I. model formulation Journal of Vibration and Control Epub ahead of print 6 February 2013. doi: 10.1177/1077546312467360 Lin M-L and Chen C-W (2013) Stability analysis of fuzzy-based NN modeling for ecosystems using fuzzy Lyapunov methods Journal of Vibration and Control Epub ahead of print 6 February 2013. doi: 10.1177/1077546312466687 Chen CY, Chen TH, Chen YH and Chiu J (2012) A multi-stage method for deterministic-statistical analysis: a mathematical case and measurement studies Journal of Vibration and Control Epub ahead of print 20 December 2012. doi: 10.1177/1077546312466579 Shih BY, Lin MC and Chen CY (2012) Autonomous navigation system for radiofrequency identification mobile robot e-book reader Journal of Vibration and Control Epub ahead of print 13 December 2012. doi: 10.1177/1077546312466578 Chang RF, Chen CY, Su FP, Lin HC and Lu C-K (2012) Multiphase SUMO robot based on an agile modeling-driven process for a small mobile robot Journal of Vibration and Control Epub ahead of print 13 December 2012. doi: 10.1177/1077546312464993 Shih B-Y, Lin Y-K, Cheng M-H, Chen C-Y and Chiu C-P (2012) The development of an application program interactive game-based information system Journal of Vibration and Control Epub ahead of print 12 December 2012. doi: 10.1177/1077546312464682 Chen C-Y, Chang C-J and Lin C-H (2012) On dynamic access control in web 2.0 and cloud interactive information hub: technologies Journal of Vibration and Control Epub ahead of print 12 December 2012. doi: 10.1177/1077546312464992 Shin BY, Chen CY and Hsu KH (2012) Robot cross platform system using innovative interactive theory and selection algorithms for Android application Journal of Vibration and Control Epub ahead of print 13 November 2012. doi: 10.1177/1077546312463757 Articles published in an issue Chen C-W (2014) Applications of neural-network-based fuzzy logic control to a nonlinear time-delay chaotic system Journal of Vibration and Control 20 (4): 589-605. Epub ahead of print 5 November 2012. doi: 10.1177/1077546312461370 Chen C-W (2014) A review of intelligent algorithm approaches and neural-fuzzy stability criteria for time-delay tension leg platform systems Journal of Vibration and Control 20 (4): 561-575. Epub ahead of print 5 November 2012. doi: 10.1177/1077546312463759 Chen C-Y, Chang C-J and Lin C-H (2014) On dynamic access control in web 2.0 and cloud interactive information hub: trends and theories Journal of Vibration and Control 20 (4): 548-560. Epub ahead of print 5 November 2012. doi: 10.1177/1077546312463762 Lin M-L and Chen C-W (2014) Stability conditions for ecosystem modeling using the fuzzy Lyapunov method Journal of Vibration and Control 20 (2): 290-302. Epub ahead of print 23 October 2012. doi: 10.1177/1077546312451301 Chen C-H, Kuo C-M, Hsieh S-H and Chen C-Y (2014) Highly efficient very-large-scale integration (VLSI) implementation of probabilistic neural network image interpolator Journal of Vibration and Control 20 (2): 218-224. Epub ahead of print 22 October 2012. doi: 10.1177/1077546312458822 Chen C-Y (2014) Wave vibration and simulation in dissipative media described by irregular boundary surfaces: a mathematical formulation Journal of Vibration and Control 20 (2): 191-203. Epub ahead of print 22 October 2012. doi: 10.1177/1077546312464258 Chen C-H, Yao T-K, Dai J-H and Chen C-Y (2014) A pipelined multiprocessor system- on-a-chip (SoC) design methodology for streaming signal processing Journal of Vibration and Control 20 (2): 163-178. Epub ahead of print 16 October 2012. doi: 10.1177/1077546312458821 Lin M-L and Chen C-W (2014) Fuzzy neural modeling for n-degree ecosystems using the linear matrix inequality approach Journal of Vibration and Control 20 (1): 82-93. Epub ahead of print 8 October 2012. doi: 10.1177/1077546312458533 Chen C-H, Wu W-X and Chen C-Y (2013) Ant-inspired collective problem-solving systems Journal of Vibration and Control 19 (16): 2481-2490. Epub ahead of print 18 September 2012. doi: 10.1177/1077546312456231 Chen C-H, Yao T-K, Kuo C-M and Chen C-Y (2013) Evolutionary design of constructive multilayer feedforward neural network Journal of Vibration and Control 19 (16): 2413-2420. Epub ahead of print 12 September 2012. doi: 10.1177/1077546312456726 Chen C-W (2013) Applications of the fuzzy-neural Lyapunov criterion to multiple time-delay systems Journal of Vibration and Control 19 (13): 2054-2067. Epub ahead of print 16 August 2012. doi: 10.1177/1077546312451034 Chung P-Y, Chen Y-H, Walter L and Chen C-Y (2013) Influence and dynamics of a mobile robot control on mechanical components Journal of Vibration and Control 19 (13): 1923-1935. Epub ahead of print 20 July 2012. doi: 10.1177/1077546312452184 Chen C-W (2013) Neural network-based fuzzy logic parallel distributed compensation controller for structural system Journal of Vibration and Control 19 (11): 1709-1727. Epub ahead of print 22 June 2012. doi: 10.1177/1077546312442233 Chen C-W, Yeh K, Yang H-C, Liu KFR and Liu C-C (2013) A critical review of structural system control by the large-scaled neural network linear-deferential-inclusion-based criterion Journal of Vibration and Control 19 (11): 1658-1673. Epub ahead of print 18 June 2012. doi: 10.1177/1077546312443377 Chen C-H, Kuo C-M, Chen C-Y and Dai J-H (2013) The design and synthesis using hierarchical robotic discrete-event modeling Journal of Vibration and Control 19 (11): 1603-1613. Epub ahead of print 27 June 2012. doi: 10.1177/1077546312449645 Chang CJ, Chen CY and Chou I-T (2013) The design of information and communication technologies: telecom MOD strength machines Journal of Vibration and Control 19 (10): 1499-1513. Epub ahead of print 27 June 2012. doi: 10.1177/1077546312449644 Shih B-Y, Chen C-Y, Li K-H, Wu T-Y, Chen G-Y (2013) A novel NXT control method for implementing force sensing and recycling in a training robot Journal of Vibration and Control 19 (10): 1443-1459. Epub ahead of print 1 June 2012. doi: 10.1177/1077546312446361 Chen C-W, Chen P-C and Chiang W-L (2013) Modified intelligent genetic algorithm-based adaptive neural network control for uncertain structural systems Journal of Vibration and Control 19 (9): 1333-1347. Epub ahead of print 31 May 2012. doi: 10.1177/1077546312442232 Chen C-Y, Shih B-Y, Shih C-H and Wang L-H (2013) Enhancing robust and stability control of a humanoid biped robot: system identification approach. Journal of Vibration and Control 19 (8): 1199-1207. Epub ahead of print 26 April 2012. doi: 10.1177/1077546312442947 Chang C-J, Chen C-Y and Huang C-W (2013) Applications for medical recovery using wireless control of a bluetooth ball with a hybrid G-sensor and human-computer interface technology Journal of Vi

Retraction notice

Many bridges in Taiwan have been in use from the period that Taiwan was governed by the Japanese, over 50 years ago, which is the average ultimate usable lifetime of such structures. Three-quarters of the bridges on major highways have been in use for more than 20 years and numerous bridges on country roads have also been in use for more than 20 years. In other words, most of the bridges in Taiwan are aging and may require repair or replacement. Ambient vibration tests are utilized to measure the response of old bridges, which are difficult to equip with accelerometers. The Fourier transform method is traditionally used to gain important information about ambient vibration records. However, the development of information technology over the last 20 years has meant that there are more kinds of signal management technologies, including the wavelet and Hilbert—Huang transform (HHT) methods. In this study we investigate the characteristics of aging bridges by comparison with their structural properties. We analyze their ambient vibration, and discuss the possible influence of the frequency function. Long-term environmental impacts create many structural problems, but with traditional methods examination of bridge health is difficult. Therefore, in our HHT management system, we examine destroyed bridges. The characteristics and behavior of bridges subjected to random loading can be understood by analysis with the random decrement technique and the frequency response function method.

Retraction notice

This paper is concerned with the control and cooperation of multiple arms mounted on a mobile platform. This represents a highly coupled and redundant system in which the motion of the arms affect that of the platform and vice versa. The objective is to develop control techniques to accurately track the motion of an object held jointly by a number of arms, while moving the platform along its desired trajectories as closely as possible. Moreover, the internal forces on the object are controlled to avoid damaging the object during manipulation. New dynamic and kinematic hybrid controllers are developed for the system. The dynamic controller is based on full model linearization while the kinematic controller utilises the concept of augmented Jacobian. The performance of the controllers is tested on a full scale simulator of two-six-degrees-of-freedom PUMA arms mounted on a three-degrees-of-freedom platform.

Compliance in multifingered hand improves grasp stability and effectiveness of the manipulation tasks. Compliance of robotic hands depends mainly on the joint control parameters, on the mechanical design of the hand, as joint passive springs, and on the contact properties. In object grasping the primary task of the robotic hand is the control of internal forces which allows to satisfy the contact constraints and consequently to guarantee a stable grasp of the object. When compliance is an essential element of the multifingered hand, and the control of the internal forces is not designed to be decoupled from the object motion, it happens that a change in the internal forces causes the object trajectory to deviate from the planned path with consequent performance degradation. This paper studies the structural conditions to design an internal force controller decoupled from object motions. The analysis is constructive and a controller of internal forces is proposed. We will refer to this controller as object motion-decoupled control of internal forces. The force controller has been successfully tested on a realistic model of the DLR Hand II. This controller provides a trajectory interface allowing to vary the internal forces (and to specify object motions) of an underactuated hand, which can be used by higher-level modules, e.g. planning tools.

Mathematical model of multiple manipulators: cooperative compliant manipulation on dynamical environments

This paper reports a method for regulating the internal forces during in hand manipulation of an unknown shaped object with soft robotic fingers. It is known that for the case of multifingered manipulation, a part of the forces applied by the fingers result in the motion of the object, whereas the other part is considered to be an internal force. The internal forces do not result in the motion of the object but are used to improve the grip on the object. For an object with unknown shape, the internal forces are regulated to ensure that the object does not slip off during manipulation. It is shown that if soft fingers show bounded conformity and the finger-object interface does not have relative slip (or a bounded slip), then the relative angular velocity between the object and the fingertip frame in contact is bounded. The proof is used to define of a new metric of relative slip. The metric is used to design a sliding mode control algorithm. The robotic fingers are assumed to be under virtual rigidity constraint, that is, the distance between the fingers do not change. The control algorithm is attractive as it skirts requirement of information of the shape of the object or to solve optimization problems. The control algorithm developed controls the internal forces and does not require the knowledge of the shape of the object. The methodology is simulated for the case of one spherical object and one conical object.

Dynamic control of soft robotic manipulators is a challenging field still in its nascent stages. Modeling is still a major hurdle due to its high dimensional nonlinear dynamic properties. Even if accurate models of these high dimensional nonlinear systems are available, the computational burden of the models or sensory requirements poses problems for robust and stable control. This letter addresses these two problems by using a data-driven model that uses only mechanical feedback for stable control of the soft robotic manipulator. Using a learning-based open loop dynamic controller, we investigate the self-stabilizing behavior that can be obtained from the complex dynamics of a soft manipulator. Experimental findings illustrate the advantage of using open-loop dynamic controllers for accurate self-stabilizing control of soft robotic manipulators without any sensory feedback.

In this paper, we extend the concept of dynamic manipulability to evaluate the dynamic property of multifingered grasping systems consisting of a multifingered hand and a grasped object, and propose a measure of dynamic manipulability of multifingered grasping. Similar to the original dynamic manipulability, the proposed measure evaluates the mapping from a set of realizable joint torques to a set of resultant accelerations of the grasped object, which forms an ellipsoid under a constant internal force constraint. It is clearly shown that the internal forces not only affect the volume of the ellipsoid, but also the amount of offset of the ellipsoid, while the gravity forces simply induce an offset. A new measure, i.e., omnidirectionality, is introduced to add a penalty to the original manipulability measure, which simply evaluates the volume of the ellipsoid, depending on how much the ellipsoid is offset. Numerical examples by using a simple two-fingered robot hand are shown to demonstrate the effectiveness of the proposed measure.

The letter studies the sampled-data-based (S-D-B) hybrid dynamic event-triggered control issue of positive Markov jump systems (PMJSs). First, taking into account positivity, a new S-D-B hybrid dynamic event-triggered method (ETM) in the shape of 1-norm is proposed, which can not only further alleviate communication burden but also avoid Zeno behavior. Furthermore, the ETM presented in this letter incorporates two internal dynamic variables, thereby enabling more flexible adjustment of resources. Utilizing the new ETM, an interval approach is introduced to analyze the positivity of closed-loop systems. By employing a co-positive Lyapunov functional (CLF) with looped-functional, a sufficient criterion is derived to ensure the stability of closed-loop systems, and an expected controller design scheme is provided in this letter. Finally, the feasibility and superiority of the proposed 1-norm-form S-D-B hybrid dynamic ETM are illustrated by an example.

This paper discusses the mechanics of coordinative manipulation by multiple robot manipulators or a multifingered robot hand. The coordinative manipulation problem is divided into two phases. One is determining the resultant force by multiple robotic mechanisms, and the other is determining the internal force between them. The resultant force is used for the manipulation of an object subjected by the external forces or the environmental constraints. The internal force is used for adapting the robotic mechanisms to uncertainty and variety of the static friction. A dynamic coordinative control scheme is proposed for determining the resultant forces. The optimal internal force is defined as the internal force that yields the minimal norm force satisfying static frictional constraints. The optimal internal force promotes the stability of prehension, while the conventional method sometimes result in too much internal force and reduce the stability. Finally, by applying a non-linear programming method, it is clarified that the optimal solution is necessarily obtained by solving, at most, 2(2 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">m</sup> -1) (m is the number of robotic mechanisms) sets of algebraic equations if it exists.

Robotics is a relatively new and evolving technology being applied to manufacturing automation and is fast replacing the special-purpose machines or hard automation as it is often called. Demands for higher productivity, better and uniform quality products, and better working environments are primary reasons for its development. An industrial robot is a multifunctional and computer-controlled mechanical manipulator exhibiting a complex and highly nonlinear behavior. Even though most current robots have anthropomorphic configurations, they have far inferior manipulating abilities compared to humans. A great deal of research effort is presently being directed toward improving their overall performance by using optimal mechanical structures and control strategies. The optimal design of robot manipulators can include kinematic performance characteristics such as workspace, accuracy, repeatability, and redundancy. The static load capacity as well as dynamic criteria such as generalized inertia ellipsoid, dynamic manipulability, and vibratory response have also been considered in the design stages. The optimal control problems typically involve trajectory planning, time-optimal control, energy-optimal control, and mixed-optimal control. The constraints in a robot manipulator design problem usually involve link stresses, actuator torques, elastic deformation of links, and collision avoidance. This paper presents a review of the literature on the issues of optimum design and control of robotic manipulators and also the various optimization techniques currently available for application to robotics.