Curcuit board application to additive manufactured components by laser-direct-structuring

Selective Photo-Thermal Conversion of Tungsten Oxide Sol Precursor for Electrochromic Smart Window Applications

Lithium-ion Batteries Fabricated Entirely with Additive Manufacturing Craig Milroy1,2, Tim Phillips1, Abhimanyu Bhat1,3, David Bourell1, Joseph Beaman1 1Department of Mechanical Engineering, University of Texas, Austin; 2Texas Research Institute, Austin; 3Evonik/Structured Polymers, Inc.There is an immediate need for disruptive battery manufacturing technologies that enable novel architectures and improve energy density by reducing packaging, interconnect, and integration requirements. Most conventional batteries are packaged in rigid metal containers with a restricted range of cell geometries and form factors; this poses major challenges for minimizing footprint and integrating batteries into small spaces. Additive manufacturing (AM) methods fabricate parts layer-by-layer by precisely assembling materials according to digitized instructions, and offer a means for simplified, top-down battery production, which provides enormous freedom to create innovative two-dimensional (2D) and 3D electrode architectural designs, customize battery form factor, and enable on-demand manufacturing. As such, AM offers a paradigm shift in electrochemical device design and manufacturing to accommodate novel geometries, improve energy density, and reduce costs. However, AM is still an emerging field, and while there have been numerous reports describing the use of AM techniques to produce components for batteries and supercapacitors, the vast majority of these efforts have focused on single components (typically the electrodes), rather than on complete systems comprising printed electrodes, separators, and cases.In this presentation, we describe methods to fabricate all necessary components of coin and pouch cells for functional prototype lithium-ion (Li-ion) batteries, using a variety of AM techniques. For example, functional graphite anodes, and cathodes based on nickel-manganese-cobalt oxide (NMC) and lithium iron phosphate (LFP), were fabricated with pneumatic extrusion, screen printing, and selective laser sintering (SLS); polymeric separators were fabricated with SLS; cases/enclosures were fabricated with SLS and direct metal laser sintering (DMLS), and metal components (e.g., foils and tabs) were fabricated with DMLS.We also utilized AM as a rapid-prototyping tool to implement novel component design approaches that improve battery performance, for example:(1) we identified improved electrode configurations by fabricating a wide range of free-standing anodes and cathodes (i.e., electrodes that do not contain or require a metal current collector) using a range of SLS fabrication parameters, then quantified the internal electrode structure/porosity with X-ray computed tomography (XCT) analyses, and used the XCT data to investigate the relationship between AM build parameters and electrochemical performance;(2) we fabricated separators with SLS using a variety of materials (i.e., polypropylene, aluminum oxide, polypropylene-polyethylene copolymer, polyether ether ketone (PEEK), polyester, and blends of these materials). SLS is well-suited to producing porous films, since spherical particles can be lightly melted to create a continuous object with ample void space, minimal membrane thickness, and maximum planar uniformity by preconditioning the printing powders (to prevent clumping), and using a machined build-plate to limit powder depth.The cycle performance of NMC-based cathodes fabricated with extrusion/direct-write and screen-printing was essentially identical to tape-cast (control) cathodes; however, the extrusion-printed cathodes exhibited more pronounced capacity-fade, and there was evidence of electrode-maturation processes, indicating the need for further optimization. The electrochemical performance of LFP-based cathodes fabricated with SLS was found to depend strongly on build setpoints and discharge rate, but exhibited robust extended cycle performance for > 300 cycles.The capacity of graphite-based anodes increased steadily over the first ~20 cycles, and strongly depended on post-SLS processing methods and the charge/discharge rate. We attribute this to the properties of the binder used in the SLS process, and to electrode maturation processes.Printed separators were tested with either tape-cast NMC-based cathodes or additively manufactured anodes/cathodes, and were cycled continuously at rates between C/5 and 2C. Specific capacity was stable and consistent at all rates, and remained above 100 mAh g-1 with no observable capacity fade for any of the rates below 2C. Extended cycling at C/1.5 stable (or even increasing) capacity for approximately 85 cycles, at which point slight capacity fade began.We evaluated the cooperative functionality of printed components (i.e., printed electrodes and separators) in both half-cell and full cell configurations (this work is ongoing). Cells containing an SLS-fabricated separator and a screen-printed NMC cathode charged at C/10 and discharged at C/5 delivered reversible capacity ~160 mAh g-1 for 100 cycles.We will also present ongoing work that uses additive manufacturing to produce flexible batteries and batteries with conformal form-factors. Figure 1

Cellular adhesion on surface structures from PA 2200 made through Selective Laser Sintering (SLS) process can be improved by modifying the parts surface. In this paper, different methods for surface modification are presented. The PA 2200 samples were immersed in six different solvents. SEM images and surface roughness tests were performed in order to evaluate the surface modification both for the control group and for the tested groups. The obtained results clearly show that there is a significant difference between the roughness of the control (untreated) surface and each of the treated surfaces. Modifying by immersion, of the PA 2200 structures produced by Selective Laser Sintering process, brings original approaches concerning the use of those procedures in the increase of the surfaces quality.

Additive manufacturing (AM) can be used without the need of any moulds or tooling, and are very suitable for manufacturing one-piece or small batches of with complex external shapes and internal structures within a short lead time, which are difficult to make or even cannot be fabricated by the tooling and machining processes. The manufacturing of metal parts by sand casting method is a tedious process when considering low volume manufacturing where it took lot of time, design cost, material cost etc., In this paper, the web gland component has been prepared using stainless steel by varying the different process parameters such as scan spacing, laser power and layer thickness in selective laser sintering (SLS) process. By using vickers hardness tester, the hardness and the microstructure of component also analyzed and it is compared with the same component properties prepared by using sand casting process. From the comparative result, it was found that the hardness of material increases by 12.5% on sintered part than casting part.

The potential advantages of pharmaceutical additive manufacturing (AM) are thoroughly described in the literature. Challenges related to pharmaceutical AM are less discussed. Selective laser sintering (SLS) is one of the AM methods possible for pharmaceutical applications. The article addresses aspects of SLS that are not typically explored in pharmaceutical studies. The literature research was conducted in parallel for both non-pharmaceutical (technical) and pharmaceutical SLS. As a result, in-depth studies on the temperature-dependent properties (rheological and optical) and thermal properties of powders for general technical printing are presented, along with the characterization of the laser sintering process. Special attention is given to the development of the "processing window" and "energy density" terms, as they continue to evolve. An application of a wide range of thermal analysis techniques is presented, including fast differential calorimetry, hot-stage microscopy, thermovision, and dielectric thermal analysis. Next, the complexity, regarding crystalline/semicrystalline/amorphous substances combination and their melt miscibility for pharmaceutical powders is marked. Pharmaceutical SLS studies are also analyzed, with emphasis on thermal aspects. Generally, pharmaceutical studies lack meaningful temperature-dependent and thermal analysis. The only significant exception is studies on drug substance amorphization during the SLS process. The main message is that pharmaceutical SLS should benefit from the methods and ideas developed for technical SLS. In particular, the research directions should include: (1) conscious powder design regarding the specificity of SLS manufacturing method, which completely different from powder compression (API - excipients matching), (2) extending the set of research methods, (3) consolidation process elucidation, (4) powder reusing or powder reusing avoiding, (5) searching for potential new carriers/excipients dedicated to pharmaceutical SLS process.

Rapid manufacturing and high accuracy are very important factor in the Selective Laser Sintering (SLS) process, one of Solid Freeform Fabrication (SFF) system due to the life cycle of a product getting shorter. This paper addressed development of an industrial SFF system which employs the new laser scan path algorithm for more elaborate and speedy system for fabricating objects compared to existing SLS process. New laser scan path algorithm called Digital Mirror System (DMS). It contains variable beam expander for getting various laser beam spot size instead of the existing fixed beam expander. Also, experiments were performed to evaluate the effect of a new laser scanning path and fabrication parameters on sintering process and to fabricate the various 3D object using polymer power.

Two types of additive manufacturing (AM) techniques, fused filament fabrication (FFF) and selective laser sintering (SLS), were employed to fabricate specimens from three widely used AM polymers: polylactic acid (PLA), acrylonitrile butadiene styrene (ABS), and polyamide (PA): the first two using FFF and PA using SLS. The single‐edge notch bending (SENB) test was employed to measure the mode‐I fracture toughnesses of bulk and AM specimens in three directions relative to the printing direction. Unlike their bulk counterparts, AM polymers exhibited anisotropic fracture toughness. The degree of anisotropy in FFF‐PLA was much larger than FFF‐ABS and SLS‐PA. The smallest fracture toughness value for each AM polymer was achieved along the transverse printing direction. Different AM techniques affect fracture toughness differently. For instance, FFF is shown to increase PLA's plastic deformation, while SLS reduces PA's ductility. The decrease in fracture toughness is consistently observed when transitioning from bulk polymers to AM ones, reaching as much as 75%. This study provides insights into the fracture toughness of AM parts made via popular plastics, which are crucial for designing structural parts using FFF and SLS processes.

As complex ceramic multicomponent materials, the lunar regolith and minerals still challenge people on onsite utilization technology limited to the lunar surface environment. In this paper, we investigate the suitability of lunar regolith simulants and ilmenite powders for 3D printing (aka Additive Manufacturing) of hypothetical brick aimed at lunar habitat construction. The first generation of laser 3D printing equipment (Lunar 1.0) for our experiments has been designed and assembled, which is suitable for selective laser sintering (SLS) process out of many kinds of ceramic powders to manufacturing samples with different geometrical shapes. The lunar regolith simulants and ilmenite powders are demonstrated obvious spectral absorbance from ultraviolet to near-infrared spectra, which are successfully performed during the SLS process in Lunar 1.0. The 3D printing technologies are constantly improved by adjusting the parameters of laser process and mechanical movement. The morphological features of 3D printed samples, including surface and porosity are investigated by using SEM. The evaluation of size and micro-hardness tests are also conducted to reveal the printing qualities of samples. The EDS and XRD results characterize the elements and components of 3D printed samples. Obviously, the strong heating process by laser source in Lunar 1.0 has a great impact on materials, because the complex multicomponent materials and solid state reaction in high temperature by SLS process for regolith simulants and ilmenite. However, this influence of heat treatment by laser source is quite different from continuously thermal treatment for ceramics such as normal high temperature furnace. In the future, the research for 3D printing of lunar regolith simulants and ilmenite powders for hypothetical brick in vacuum and low gravity will carry out for approaching the extreme manufacturing environment on lunar surface.

Among the various additive manufacturing processes, there is selective laser sintering, with the use of a high-power laser that sinters the small particles of polymer powder and turn them into a solid structure, from a 3D model, nowadays SLS additive manufacturing has become the best choice for the industry, especially for polymer materials, SLS ensures high productivity and well-honed materials at low cost. Recent Advances in Fitting, the materials and software have made SLS printing accessible to a wider range of activities. Our study is to show the mechanism of polymer particle suspension during the three stages of SLS printing, we start with printing first, the polymer powder in a thin layer applied on a flat shape inside the build chamber and the printer will heat the powder until the polymer melts, Allowing the laser to easily increase the temperature in specific areas in the powder bed to trace the morphology of the solidified part. Secondly, cooling and finally post-processing to extract the finished parts from the build chamber. In our study, we will analyze the suspension of small polymer powder particles in the SLS printing process. We will start with the mathematical formulation of the problem with an experimental study of the polymer sample studied. Next, we will set up the chosen solution method and finally the modeling of the results obtained on the FORTRAN language.

The process of selective laser sintering (SLS) involves selective heating and fusion of powdered material using a moving laser beam. Because of its complicated manufacturing process, physical modeling of the transformation from powder to final product in the SLS process is currently a challenge. Existing simulations of transient temperatures during this process are performed either using finite-element (FE) or discrete-element (DE) methods which are either inaccurate in representing the heat-affected zone (HAZ) or computationally expensive to be practical in large-scale industrial applications. In this work, a new computational model for physical modeling of the transient temperature of the powder bed during the SLS process is developed that combines the FE and the DE methods and accounts for the dynamic changes of particle contact areas in the HAZ. The results show significant improvements in computational efficiency over traditional DE simulations while maintaining the same level of accuracy.

Additive Manufacturing with Bioinspired Sustainable Product Design: A Conceptual Model

Selective laser sintering (SLS) is one of the most well-regarded additive manufacturing (AM) sub-processes, whose popularity has been increasing among numerous critical and demanding industries due to its capabilities, mainly manufacturing parts with highly complex geometries and desirable mechanical properties, with potential to replace other, more expensive, conventional processes. However, due to its various underlying multi-physics phenomena, the intrinsic complexity of the SLS process often hampers its industrial implementation. Such limitation has motivated academic interest in obtaining better insights into the process to optimize it and attain the required standards. In that regard, the usual experimental optimization methods are time-consuming and expensive and can fail to provide the optimal configurations, leading researchers to resort to computational modeling to better understand the process. The main objective of the present work is to develop a computational model capable of simulating the SLS process for polymeric applications, within an open-source framework, at a particle-length scale to assess the main process parameters' impact. Following previous developments, virgin and used polymer granules with different viscosities are implemented to better represent the actual process feedstock. The results obtained agree with the available experimental data, leading to a powerful tool to study, in greater detail, the SLS process and its physical parameters and material properties, contributing to its optimization.

This study investigates the influence of tooth layer orientation on the bending fatigue behaviour of Nylon 12 spur gears manufactured by a selective laser sintering process in an ‘on-edge’ configuration. The test gears were submitted to single tooth bending fatigue tests, and the thermal response of gears was recorded using Infrared thermography. The surface morphology of failed teeth was examined using microscopy. The effect of tooth layer orientation on the fatigue strength of selective laser sintering gears was evaluated by testing each tooth configuration. The tooth configurations with the highest and lowest strength were 40° and 160°, respectively. The performance of selective laser sintering gears was compared with that of injection moulded Nylon 66 gears. The injection moulded, selective laser sintering 40°, and selective laser sintering 160° gear teeth were tested at multiple loads to investigate the high cycle fatigue and low cycle fatigue behaviour. The bending fatigue life was highest for the injection moulded gears in both low cycle fatigue and high cycle fatigue regimes. The surface temperature was higher in selective laser sintering gears, with 160° configuration exhibiting the highest temperature. The difference between the temperatures of selective laser sintering 40° configuration and injection moulded gear magnified as the applied load increased. Consequently, the strength of the selective laser sintering 40° configuration with respect to injection moulded gear deteriorated in the low cycle fatigue region. Fractography indicated that crack propagation in selective laser sintering 40° and selective laser sintering 160° configurations were cross-laminar and inter-laminar, respectively. In the cross-laminar mode of propagation, the crack propagation was impeded by the layer structure. However, the crack propagation was expedited in the inter-laminar mode, as the crack path was along the interlayer region, which presents a path of least resistance.

The abstract aims to investigate the comparative performance of Electrical Discharge Machining (EDM) and Selective Laser Sintering (SLS) with unconventional machining processes. Unconventional machining processes have gained significant attention due to their versatility and capability to fabricate intricate components with high precision. This study focuses on assessing the efficacy of EDM and SLS techniques in terms of data removal rate and relative wear volume. Electrical Discharge Machining (EDM) is a thermal erosion process that utilizes electrical discharges to remove material from a workpiece. In contrast, Selective Laser Sintering (SLS) is an additive manufacturing technique that employs a laser to selectively fuse powdered material, layer by layer, to build up a three-dimensional object. Both methods offer unique advantages in terms of precision, speed, and material compatibility. The performance evaluation of these techniques involves analyzing key parameters such as data removal rate, which measures the volume of material removed per unit time, and relative wear volume, which quantifies the wear on the tool or workpiece during the machining process. By comparing these metrics, insights into the efficiency and effectiveness of EDM and SLS can be gained, aiding manufacturers and researchers in selecting the most suitable method for specific applications. Through experimental investigations and data analysis, this study aims to provide valuable insights into the capabilities and limitations of EDM and SLS in unconventional machining processes. The findings will contribute to advancing the understanding of these techniques and optimizing their utilization in various industrial sectors, including aerospace, automotive, and biomedical engineering. The experimental analysis examines the impact of the Direct Metal Laser Sintering (DMLS) process parameter on sintering depth. The optimized parameters for AlSi10Mg alloy powder sintering were obtained using laser power at 162 W, scanning speed at 156 mm s−1, porosity at 20%, laser area size of 0.2 mm, and layer thickness of 1 mm.

Selective Laser Sintering (SLS) is an Additive Manufacturing (AM) technology that is receiving considerable attention in the scientific and industrial communities due to its great ability to efficiently produce functional and complex parts. The present work aims to fabricate a real prototype via SLS, such as a hose reel for industrial applications, using polyamide 11 (PA11) as a starting material. Characterization of the PA11 powder properties was first carried out from a thermal and morphological viewpoint to determine the powder's thermal stability by TGA, the sintering window and degree of crystallinity by DSC, and the microstructure by SEM, PSD, and XRD analyses. The results revealed that PA11 has a 45-micron average particle size, circularity close to 1, and a Hausner ratio of 1.17. Together, these parameters ensure that PA11 powder flows smoothly, packs uniformly, and forms dense and defect-free layers during the SLS process, directly contributing to high part quality, dimensional precision, and stable process performance. The printability of the PA11 was optimized for the realization of 3D-printed parts for industrial applications. Finally, the quality of the printed samples and the mechanical and thermal performance were investigated. Several PA11-based parts were fabricated via SLS, showing a high level of complexity and definition, ideal for industrial applications, as confirmed by the predominantly green areas of the colored maps of X-CT. A complete prototypal case for a hose reel was assembled by using the parts realized, and it was chosen as a technological demonstrator to verify the feasibility of PA11 powder in the production of industrial professional components.