Defect analysis on actinic blank inspection tool

One challenge of extreme ultraviolet (EUV) mask defectivity is the severe printability of defects of the multi-layer (ML) mirror on the mask. These ML-defects are just nanometer high or deep local distortions of this ML mirror. Dedicated blank inspection tools have become available over time. One of them is the actinic blank inspection tool under development through EIDEC (Lasertec ABI). EIDEC and imec have jointly correlated its blank defect detection capability to wafers printed on ASML NXE3100 and NXE3300 scanners. Printing ML-defects were identified by wafer inspection, followed by subsequent repeater analysis, and correlated back to blank inspection. Forward correlation of ABI detections to the printed wafer was also successfully undertaken. The focus of this work has been on native defects. This paper will discuss the obtained results from the perspective of how to use ABI to assess which kind of native ML defects need to be avoided during blank fabrication.

The key challenge before EUVL is to make defect-free masks, for which it is important to identify the root cause of defects, and it is also necessary to establish suitable critical mask defect size for the production of ULSI devices. Selete has been developing EUV mask infrastructures such as a full-field actinic blank inspection tool and 199nm wavelength patterned mask inspection tool in order to support blank/mask supplier in reducing blank/mask defects which impact on wafer printing. In this paper, by evaluating the printability of programmed phase defects and absorber defects exposed by full-field scanner EUV1, we demonstrate that defect detection sensitivities of ABI (actinic blank inspection) and PI (patterned mask inspection) are higher than that of WI (wafer inspection) in HP32nm. The evaluations were done by comparing the detection sensitivities of full-field actinic blank inspection tool, 199nm wavelength patterned mask inspection tool, and wafer EB inspection tool. And then, based on the native defect analysis of blank/mask, we ascertained that actinic blank inspection and patterned mask inspection developed at Selete, are effective in detecting killer defects both at the main pattern and at light-shield border area.

Improvements in the detection capability of a high-volume-manufacturing (HVM) actinic blank inspection (ABI) prototype for native defects caused by illumination numerical aperture (NA) enlargement were evaluated. A mask blank was inspected by varying the illumination NA. The defect signal intensity increased with illumination NA enlargement as predicted from simulation. The mask blank was also inspected with optical tools, and no additional phase defect was detected. All of the printable phase defects were verified to have been detected by the HVM ABI prototype.

Implementation of extreme ultra violet lithography (EUVL) for printing features of dimensions around 32nm and below has faced multiple challenges that have been overcome mostly through tool and process engineering. Currently, the main concern for implementation of EUVL in high volume manufacturing is related to stochastic defects, such as line bridges or breaks, which may occur randomly and have an impact on device performance.1 Photon shot noise, in addition to the inherent process variability and material non-homogeneities can lead to defects on the final patterned structures. As the pitch and critical dimension (CD) approach 32nm pitch and below, the dependency of stochastics defects increases exponentially. This paper fits within imec’s EUV stochastics and defectivity program, which investigates the key parameters for the generation and mitigation of defects from both a theoretical and practical approach. Initially, a reference process has been established and a methodology has been developed to capture and characterize bridge-type defects after pattern transfer into relevant layers for metrology and applications. Optical inspection and scanning electron microscopy (SEM) review are used to collect information on the number and types of defects present over large patterned areas (in the order of cm2). With a well-defined inspection technique, experiments related to fundamentals as well as materials and processes are continuously run. In the past years, imec has been leading the fundamental work on stochastic defects.2,3 De Bisschop et al. identified the “defect cliff”, or the exponential dependency of defect density as a function of space CD for multiple parameters, such as resist formulation and exposure/imaging conditions. More recently, the focus has changed to the investigation of the “defect floor”, which as the name suggests, is a flat response of defects to CD. The defect floor suggests that defectivity cannot be further improved, making one of the most relevant problems to solve for implementation of EUV in high volume manufacturing (HVM). Our results show a decomposition of the potential contributors to explore the effect of processing conditions related to scanner, track and pattern transfer on final defect density for a chemically amplified resist and attempt a comparison to a metal-oxide resist. Goal is to understand the contributors to the defect floor and identify an effective route to avoid/minimize defect formation.

Extreme ultraviolet (EUV) lithography is crucial to enabling technology scaling in pitch and critical dimension (CD). Currently, one of the key challenges of introducing EUV lithography to high volume manufacturing (HVM) is throughput, which requires high source power and high sensitivity chemically amplified photoresists. Important limiters of high sensitivity chemically amplified resists (CAR) are the effects of photon shot noise and resist blur on the number of photons received and of photoacids generated per feature, especially at the pitches required for 7 nm and 5 nm advanced technology nodes. These stochastic effects are reflected in via structures as hole-to-hole CD variation or local CD uniformity (LCDU). Here, we demonstrate a synergy of film stack deposition, EUV lithography, and plasma etch techniques to improve LCDU, which allows the use of high sensitivity resists required for the introduction of EUV HVM. Thus, to improve LCDU to a level required by 5 nm node and beyond, film stack deposition, EUV lithography, and plasma etch processes were combined and co-optimized to enhance LCDU reduction from synergies. Test wafers were created by depositing a pattern transfer stack on a substrate representative of a 5 nm node target layer. The pattern transfer stack consisted of an atomically smooth adhesion layer and two hardmasks and was deposited using the Lam VECTOR PECVD product family. These layers were designed to mitigate hole roughness, absorb out-of-band radiation, and provide additional outlets for etch to improve LCDU and control hole CD. These wafers were then exposed through an ASML NXE3350B EUV scanner using a variety of advanced positive tone EUV CAR. They were finally etched to the target substrate using Lam Flex dielectric etch and Kiyo conductor etch systems. Metrology methodologies to assess dimensional metrics as well as chip performance and defectivity were investigated to enable repeatable patterning process development. Illumination conditions in EUV lithography were optimized to improve normalized image log slope (NILS), which is expected to reduce shot noise related effects. It can be seen that the EUV imaging contrast improvement can further reduce post-develop LCDU from 4.1 nm to 3.9 nm and from 2.8 nm to 2.6 nm. In parallel, etch processes were developed to further reduce LCDU, to control CD, and to transfer these improvements into the final target substrate. We also demonstrate that increasing post-develop CD through dose adjustment can enhance the LCDU reduction from etch. Similar trends were also observed in different pitches down to 40 nm. The solutions demonstrated here are critical to the introduction of EUV lithography in high volume manufacturing. It can be seen that through a synergistic deposition, lithography, and etch optimization, LCDU at a 40 nm pitch can be improved to 1.6 nm (3-sigma) in a target oxide layer and to 1.4 nm (3-sigma) at the photoresist layer.

In 2019, finally, extreme ultraviolet (EUV) lithography has been applied to high volume manufacturing (HVM) for preparing advanced semiconductor devices. That was very important year for EUV enthusiasts and semiconductor industry. Because it takes for a long time, more than 30 years, to study EUV lithography for realizing HVM. With recent rapid progress on the source power improvement, EUV lithography development including photoresist materials has been achieved HVM requirements. However, the performance of EUV resist materials are still not enough for the expected HVM requirements, even by using the latest qualifying EUV resist materials. One of the critical issues is the stochastic issues, which will be become ‘defectivity’, like a nano-bridge or a nano-pinching. The analyzing summary of the stochastic factors in EUV lithography, and their improvement status are described in this paper. 2 (two) major stochastic issues, which are photon stochastic and chemical stochastic, were observed in the lithography steps. And the improvement status of each stochastic issues including lithographic results are also described.

The following topics are dealt with: low-power electronics; Internet of Things; integrated circuit design; video coding; integrated circuit manufacture; CMOS integrated circuits; field programmable gate arrays; magnetic sensors; calibration; power consumption.

Recent rapid progress in the technologies of extreme ultraviolet lithography (EUVL) is ensuring that EUVL will be a primary candidate for the next generation lithography beyond 32-nm node. However, realization of defect-free reflective mask blank is still counted as one of the most critical issues for high volume production in EUVL. Asahi Glass Company (AGC) has developed comprehensive technologies for manufacturing EUVL mask blanks from figuring and polishing glass substrate to cleaning, multilayer coating, and evaluating its performances by making use of our long and wide experience in providing high quality processed glass substrates and coatings for electronic devices. In this paper, we will present the current status of each aspect of EUVL mask blank development in AGC toward the specifications required for high volume production. In the effort to meet the specifications, we have introduced a number of key technologies that can be divided into three regions, which are materials, glass processings, and evaluations. We have developed state-of-the-art processes and tools for manufacturing EUV mask blanks, such as a new polishing technique for extremely flat substrate, a new cleaning recipe and tool for low-defect substrate, and a newly developed deposition tool for ultra-low defect and higher EUV reflective coating with our new optical thin film materials for multilayer coating. Furthermore, in order to clarify their performances, we also introduced a wide variety of evaluation techniques such as flatness and roughness measurement of substrate, a defect inspection, and EUV reflectometry as well as defect analysis techniques which help us eliminate printable defects in EUVL mask blanks.

Extreme ultraviolet lithography (EUVL) is the leading technology for patterning at the 32 nm technology node and be-yond. EUVL light at 13.5 nm is used to print circuits. This light is produced by heating fuel (Xe, Sn) in EUV sources to a very high temperature by using either magnetic compression or laser irradiation. Today EUV source power remains the number one concern for implementation of EUVL in high volume manufacturing. Over the last few years, much pro-gress has been made in EUV source performance and availability. Today, alpha level high power (~10 W) EUV sources have been integrated in alpha level EUVL scanners. Medium and low power EUV sources are used for in-house metrol-ogy and performance studies on EUV mask blanks, EUV masks, photoresists, and optical elements. These compact dis-charge sources with medium power in the range of 10-100 mW/sr/2% bandwidth and low power EUV tubes are being used by various RD today, these low power EUV sources are instrumental in allowing in-house R&D projects. In this paper, the latest status of high power EUV sources, low and medium power metrology sources, and some of their appli-cations are described.

Extreme-UV lithography (EUVL) is the most promising candidate of next generation technology for hp20nm node device manufacturing and beyond, however there are many critical issues to solve in the light source, tools, mask and photo resist. Regarding the development of a photo resist, it is necessary for high volume manufacturing (HVM) to improve LWR, resolution limit and sensitivity. Additionally, concerning about deterioration of a patterning performance by Out-of-Band (OoB) light existing in the EUV light, and contamination problem of exposure tool due to the photo resist outgassing are the key issues which have to be resolved toward HVM by EUVL. Especially, the outgassing problem can become a significant issue for fine patterning under high dose exposure condition. This paper proposes the novel solution for these critical issues with the application of a top coat material which is named OBPL (Outgassing & out-of-Band Protection Layer) on photo resist. The key characteristics of OBPL material are to have a role in protection against the OoB adverse effect to keep up the photo resist performance, to suppress the outgassing from photo resist as a barrier layer and to enhance the lithographic performance such as photo resist profile and process window. In designing the OBPL material, the optical property needs having not only the high absorbance of DUV (Deep-UV) light in OoB range but also high transmittance for 13.5nm wavelength to prevent the sensitivity loss. Furthermore, it is found that the polymer backbone affects the outgassing barrier capability in previous evaluation. Based on these investigations, a state-of-the-art OBPL achieves quite a positive lithographic result with sufficient OoB absorption and outgassing suppression. Moreover, this material has applicability to all types of photo resist including NTD (Negative-Tone Development) process. This paper describes the result of the feasibility study for OBPL and the lithography performance with EUV full field scanner.

Intel's efforts to build a practical quantum computer are focused on developing a scalable spin-qubit platform leveraging industrial high-volume semiconductor manufacturing expertise and 300 mm fabrication infrastructure. Here, we provide an overview of the design, fabrication, and demonstration of a new customized quantum test chip, which contains 12-quantum-dot spin-qubit linear arrays, code named Tunnel Falls. These devices are fabricated using immersion and extreme ultraviolet lithography (EUV), along with other standard high-volume manufacturing (HVM) processes as well as production-level process control. We present key device features and fabrication details as well as qubit characterization results confirming device functionality. These results corroborate our fabrication methods and are a crucial step toward scaling of extensible 2D qubit array schemes.

EUV lithography (EUVL) is the candidate for next generation lithography to be introduced by the semiconductor industry to HVM (high volume manufacturing) in 2013. The power of the EUVL light source has to be at least 115W at a wavelength of 13.5nm. A laser produced plasma (LPP) is the main candidate for this light source but a cost effective laser driver is the key requirement for the realization of this concept. We are currently developing a high power and high repetition rate CO 2 laser system to achieve 50 W intermediate focus EUV power with a Tin droplet target. A high conversion efficiency (CE) from laser energy to EUV in-band energy is the most important issue for the concept to be realized. A CE of more than 2 % has been obtained with a Tin target and a CO 2 laser which is also predicted by numerical simulation analysis. The high CE requires a short laser pulse of less than 15 ns. This paper describes the development of a CO 2 laser system that is based on RF-excited, axial flow CO 2 laser amplifiers. The system produces a short pulse length about 15 ns and a nominal average power of several kW at a repetition rate of 100 kHz, An output power of 2.6 kW has been achieved with a pulse length between 15~30 ns at 130 kHz repetition rate at small signal amplification. The phase distortion of the laser beam after amplification is negligible and the beam can be focused to about 150mm diameter in 1/e 2 . The conceptual design of the CO 2 laser system for LPP EUVL light source, and the laser performance are reported. The further increase of the amplification efficiency is discussed to obtain 5 kW average output power.

Extreme ultraviolet (EUV) lithography is considered as the leading patterning technology beyond the ArF-based optical lithography, addressing the need for transistor densification to meet Moore's Law. Theoretically, EUV lithography at 13.5nm wavelength meets the resolution requirements for 1xnm technology nodes. However, there are several major challenges in the development of EUV lithography for mass production of advanced CMOS devices. These include the development of high power EUV light sources, EUV optics, EUV masks, EUV resists, overlay accuracy, and metrology and inspection capabilities. In particular, it is necessary to ensure that effective defect control schemes will be made available to reduce the EUV lithography defectivity to acceptable levels. This paper presents a study on the wafer defectivity and characterization of patterned EUV resists, with the objective of providing a quantitative comparison between the defectivity of different resist materials and different stacks. Patterned wafers were printed using the ASML® EUV full-field Alpha-Demo Tool (ADT 0.25 NA) at imec. The EUV resist patterns were 32nm line/spaces. Several advanced resist types were screened experimentally. The different resist types and stacks were inspected using a DUV laser based brightfield inspection tool, followed by a SEM defect review and CD metrology measurements. The patterns were characterized in terms of defect types and defect density. We identified the major defect types and discuss factors that affect the defectivity level and pattern quality, such as resist type, exposure dose and focus. Defect scattering analysis of DUV polarized light at different polarizations was performed, to indicate on the inspection performance trends for a variety of defect types and sizes of the different resists and stacks. The scattering analysis shows that higher defect scattering is induced using polarized light.

The printability of buried extreme ultraviolet (EUV) defects near absorber features is studied using aerial images from the actinic inspection tool (AIT) and the fast EUV mask simulation program RADICAL. This work begins by comparing the printability of isolated defects through focus predicted by RADICAL and measured by the AIT. Then, images of defects near features from both simulation and experiment are investigated for different defect sizes and positions through focus. Finally, RADICAL is used to assess the expected defect printability levels in the less in coherent conditions which are expected to be used for production. Defect printability will be investigated as a function of defect size, position, and focus for the small absorber lines critical to 22nm imaging using a top-hat illumination condition of sigma=0.75. Here, defects as small as 0.8nm surface height cause a critical dimension (CD) change greater than 10% at best focus when located in the worst case position. Defects as small as 2.2nm cause a CD change greater than 10% even when located under the center of the absorber.

As commercialization of extreme ultraviolet lithography (EUVL) progresses, direct industry activities are being focused on near term concerns. The question of long term extendibility of EUVL, however, remains crucial given the magnitude of the investments yet required to make EUVL a reality. Extendibility questions are best addressed using advanced research tools such as the SEMATECH Berkeley microfield exposure tool (MET) and actinic inspection tool (AIT). Utilizing Lawrence Berkeley National Laboratory's Advanced Light Source facility as the light source, these tools benefit from the unique properties of synchrotron light enabling research at nodes generations ahead of what is possible with commercial tools. The MET for example uses extremely bright undulator radiation to enable a lossless fully programmable coherence illuminator. Using such a system, resolution enhancing illuminations achieving k1 factors of 0.25 can readily be attained. Given the MET numerical aperture of 0.3, this translates to an ultimate resolution capability of 12 nm. Using such methods, the SEMATECH Berkeley MET has demonstrated resolution in resist to 16-nm half pitch and below in an imageable spin-on hard mask. At a half pitch of 16 nm, this material achieves a line-edge roughness of 2 nm with a correlation length of 6 nm. These new results demonstrate that the observed stall in ultimate resolution progress in chemically amplified resists is a materials issue rather than a tool limitation. With a resolution limit of 20-22 nm, the CAR champion from 2008 remains as the highest performing CAR tested to date. To enable continued advanced learning in EUV resists, SEMATECH has initiated a plan to implement a 0.5 NA microfield tool at the Advanced Light Source synchrotron facility. This tool will be capable of printing down to 8-nm half pitch.