Design and implementation of a buck converter-based PV emulator using dynamic evolution control

Photovoltaic (PV) emulator (PVE) allows the development and testing of the PV equipment and system effectively. The PVE is an alternative to controllable light source that requires a large space and highly inefficient. The PVE requires a power converter and the buck converter is preferred due to the control simplicity and high efficiency. Nonetheless, the conventional design of the buck converter cannot be used since the output voltage of the PVE highly dependent on the output resistance. A proper design of the buck converter specified for the PVE application is needed to maintain continuous current mode operation and the output voltage ripple factor below the desired specification. This paper proposed the design for the passive components for the PVE using buck converter, which includes the output resistor, inductor, and capacitor. The single diode model is used to produce the current-resistance characteristic curves of the PV. The control strategy of the PVE is not included in this paper. The results show that the passive components for the buck converter obtained from the derivation able to maintain continuous current mode and has the output voltage ripple factor lower than the desired specification when operates as the PVE. This proves the derivation of the passive components is accurate.

The first lactation weekly test day milk yield (WTDMY) records (57233) and monthly test day milk yield (MTDMY) records (11970) spread over a period of 23 years (1984– 2006) sired by 82 bulls of Karan Fries cattle were used to develop the best lactation curve model. The lactation curve parameters of Quadratic cum log model (QCLM), Gamma function (GF), Cobby Le Du model (CLDM), Polynomial regression function (PRF) and Multiphasic logistic function (MLF) were estimated. The average weekly test day milk yield was predicted with high degree of accuracy (R2 > 85%) by all the models with the maximum accuracy (R2 = 99.50%) obtained by polynomial regression function (PRF) and the least fit (R2 = 87.90%) was obtained by Gamma function (GF). However Quadratic cum log model (R2 = 99.20%) was almost equal to polynomial regression function and was better than Cobby Le Du model (R2 = 92.80%). The average root mean square error (RMSE) was found to be minimum with PRF (0.0121 Kg) followed by MLF (Triphasic). Thus the best fit model was polynomial regression function, which was better than other functions for prediction of first lactation WTDMY. The average monthly test day milk yield was predicted with high degree of accuracy (R2 > 75%) by all the models with the maximum accuracy (R2 > 99.41%) obtained by polynomial regression function (PRF) and the least fit was obtained with gamma function (R2 = 79.05%). However, quadratic-cum-log model (R2 = 99.28%) was almost equal to polynomial regression function and was better than CLDM (R2 = 89.50%). The average root mean square error (RMSE) was found to be minimum with PRF (0.0061 kg) followed by QCLM (0.0620). Thus the best fit model was polynomial regression function for prediction of both weekly and monthly test day milk yield of first lactation in Karan Fries cows.

Phenological shifts in plant species are one of the most conspicuous signs of climate change impact on the biosphere. Modeling phenological variations of plant species over broad regions is challenging because of the varied climatic requirements of geographic populations due to local adaptation. In this study, we developed an empirical method to calibrate phenological models of temperate trees using latitude as a predictor to account for local adaptation of populations to a N-S temperature gradient. Fourteen widely distributed tree species in the eastern U.S.A. were investigated using data from the USA-National Phenology Network. We implemented the method in a basic thermal time bud break model to introduce the algorithm of the method and test its effectiveness. For each species, dates of breaking leaf buds were first predicted using a traditional non-spatial model and then with a spatial model that has the critical thermal forcing requirements calibrated for different populations at varied latitudes. As anticipated, non-spatial model predictions that assumed a uniform forcing requirement across latitudes showed consistent and systematic biases at both higher (overestimation-predictions being later) and lower (underestimation-predictions being earlier) latitudes. Spatial models that have been calibrated using our method removed the geographic biases and yielded latitudinal gradients that more closely matched those of the observations. The spatial models also reduced the overall prediction errors from an average root mean square error (RMSE) of 32.2 days to 20.4 days for the training dataset and an average root mean square error for prediction (RMSEP) of 32.2 days to 19.9 days for the testing dataset. This paper is focused on introducing the new calibration method as a preparatory step toward developing operational models that may potentially predict large-scale and range-wide phenological responses of various plant species to climatic changes with improved local accuracy.

Traditional photovoltaic (PV) power prediction methods in microgrids are insensitive to weather characteristics, and fluctuations in weather data can lead to insufficient PV power prediction accuracy. Therefore, this paper proposes a short-term PV power prediction method for microgrids based on FCM–QPSO–LSTM, which is used to predict PV power under different seasons and weather types. First, the fuzzy [Formula: see text]-means clustering algorithm (FCM) is used to perform clustering analysis on multi-source weather data, and the initial dataset is clustered into sunny, cloudy, and rainy days. Second, to address the shortcomings of a single long-short-term memory (LSTM) model in terms of prediction accuracy and stability, the quantum particle swarm optimization (QPSO) algorithm is used to optimize the model of the LSTM network, and the QPSO–LSTM prediction model is constructed. By introducing quantum dynamic inertia weights and adaptive learning factors, the QPSO algorithm enhances the global search capability and local search capability, which greatly improves the prediction accuracy and stability of the prediction model. Finally, the average absolute percentage error and root mean square error (RMSE) are applied as evaluation indexes to assess the performance of the prediction model. The simulation results show that the QPSO–LSTM model is better than the single LSTM model and the traditional PSO–LSTM model in terms of the average absolute percentage error and RMSE indicators and is able to make accurate predictions of short-term PV power under different seasons and weather types.

This paper presents modeling and experimental studies on water spray coolers for commercial photovoltaic modules. This paper has compared the energy yield of four photovoltaic commercial modules that were installed with a fixed tilt angle being equal to the local latitude in central Vietnam, including one photovoltaic module using a water spray cooler and three photovoltaic modules without cooling. Experimental results on sunny days have been shown that the energy yield difference between four PV modules under the same working condition is lower than 1%. In addition, on sunny days when the set working temperature of the water spray cooler is 45 °C, the average improvement efficiency of a photovoltaic module using a water spray cooler compared to three reference photovoltaic modules is 2.64%, 3.83%, and 6.18%, for an average of 4.22%. A simple thermal–electrical model of a photovoltaic module with a water spray cooler has been developed and tested. The normalized root mean square error between simulated and measured results of photovoltaic module power output on a sunny day without cooling and with water spray cooler reached 6.5% and 8.5%, respectively. The obtained results are also demonstrated that the reasonableness of the simple thermal–electrical model of the photovoltaic module with water spray cooler and the feasibility of a cooling system is improved to increase the efficiency of the photovoltaic module. In addition, they can be considered as a basis for new experimental models in the future.

ABSTRACTUpdating of reservoir models by history matching of 4D seismic data along with production data gives us a better understanding of changes to the reservoir, reduces risk in forecasting and leads to better management decisions. This process of seismic history matching requires an accurate representation of predicted and observed data so that they can be compared quantitatively when using automated inversion. Observed seismic data is often obtained as a relative measure of the reservoir state or its change, however. The data, usually attribute maps, need to be calibrated to be compared to predictions. In this paper we describe an alternative approach where we normalize the data by scaling to the model data in regions where predictions are good. To remove measurements of high uncertainty and make normalization more effective, we use a measure of repeatability of the monitor surveys to filter the observed time‐lapse data.We apply this approach to the Nelson field. We normalize the 4D signature based on deriving a least squares regression equation between the observed and synthetic data which consist of attributes representing measured acoustic impedances and predictions from the model. Two regression equations are derived as part of the analysis. For one, the whole 4D signature map of the reservoir is used while in the second, 4D seismic data is used from the vicinity of wells with a good production match. The repeatability of time‐lapse seismic data is assessed using the normalized root mean square of measurements outside of the reservoir. Where normalized root mean square is high, observations and predictions are ignored. Net: gross and permeability are modified to improve the match.The best results are obtained by using the normalized root mean square filtered maps of the 4D signature which better constrain normalization. The misfit of the first six years of history data is reduced by 55 per cent while the forecast of the following three years is reduced by 29 per cent. The well based normalization uses fewer data when repeatability is used as a filter and the result is poorer. The value of seismic data is demonstrated from production matching only where the history and forecast misfit reductions are 45% and 20% respectively while the seismic misfit increases by 5%. In the best case using seismic data, it dropped by 6%. We conclude that normalization with repeatability based filtering is a useful approach in the absence of full calibration and improves the reliability of seismic data.

Photovoltaic (PV) sources are inherently nonlinear power devices and maximum power derivation depends on Maximum Power Point Tracking (MPPT) algorithms. The algorithms require testing in real time situation using PV source which will be troublesome due to higher dependency on environmental factors and larger space requirements for higher power rating. The increased and faster testing lead to develop a PV emulator with desired performance and lower price compare to the commercially available PV emulators. In this paper, design of a digitally controlled PV emulator with varying resistive load is proposed to replicate the behaviour of real PV sources. The power stage of the PV emulator is realized using dc-dc buck converter topology and the controller stage uses an algorithm-in-loop Newton-Raphson (NR) method. Finally, the PV emulator is tested with MPPT controlled dc-dc boost converter for battery charging. The design of the power and control stages of the PV emulator has been compared with the real PV source and it is observed that the obtained V-I characteristic is in good agreement. Moreover, an analysis is presented for different switching frequencies of the boost converter connected as load to the fixed switching frequency buck converter, i.e., PV emulator. Further, a schematic hardware circuit diagram has been given to realize the proposed digitally controlled PV emulator.

Leaf biochemical traits indicating early symptoms of plant stress can be assessed using imaging spectroscopy combined with radiative transfer modelling (RTM). In this study, we assessed the potential applicability of the leaf radiative transfer model Fluspect-Cx to simulate optical properties and estimate leaf biochemical traits through inversion of two native Australian eucalypt species: Eucalyptus dalrympleana and E. delegetensis. The comparison of measured and simulated optical properties revealed the necessity to recalibrate the refractive index and specific absorption coefficients of the eucalypt leaves’ biochemical constituents. Subsequent validation of the modified Fluspect-Cx showed a closer agreement with the spectral measurements. The average root mean square error (RMSE) of reflectance, transmittance and absorptance values within the wavelength interval of 450–1600 nm was smaller than 1%. We compared the performance of both the original and recalibrated Fluspect-Cx versions through inversions aiming to simultaneously retrieve all model inputs from leaf optical properties with and without prior information. The inversion of recalibrated Fluspect-Cx constrained by laboratory-based measurements produced a superior accuracy in estimations of leaf water content (RMSE = 0.0013 cm, NRMSE = 6.55%) and dry matter content (RMSE = 0.0036 g·cm−2, NRMSE = 21.28%). The estimation accuracies of chlorophyll content (RMSE = 8.46 µg·cm−2, NRMSE = 24.73%), carotenoid content (RMSE = 3.83 µg·cm−2, NRMSE = 30.82%) and anthocyanin content (RMSE = 1.69 µg·cm−2, NRMSE = 37.12%) were only marginally better than for the inversion without any constraints. Additionally, we investigated the possibility to substitute the prior information derived in the laboratory by non-destructive reflectance-based spectral indices sensitive to the retrieved biochemical traits, resulting in the most accurate estimation of carotenoid content (RMSE = 3.65 µg·cm−2, NRMSE = 29%). Future coupling of the recalibrated Fluspect with a forest canopy RTM is expected to facilitate retrieval of biophysical traits from spectral air/space-borne image data, allowing for assessing the actual physiological status and health of eucalypt forest canopies.

Empirical ocean color algorithms and bio-optical properties of the western coastal waters of Svalbard, Arctic

Application of Landsat-8 and Sentinel-2 for retrieval of chlorophyll-a in a shallow freshwater lake

Forecasting Occupants’ Presence and Photovoltaic Power using an Enhanced Stacking Algorithm for Demand/Supply Energy Management

Prediction of photovoltaic power output based on similar day analysis, genetic algorithm and extreme learning machine

<span>A Photovoltaic (PV) emulator is a device that produces a similar output as the PV module and it is useful for testing the PV generation system. This paper present a new and simple control strategy for the PV emulator using the combination of the Resistance Comparison Method with the Integral Controller. The closed-loop buck converter system with the current-mode controlled and the single diode model are used for the PV emulator. The results obtained from the proposed PV emulator are compared with the conventional PV emulator using the Direct Referencing Method as the control strategy. The proposed PV emulator produces a more accurate output, 74 % faster transient response, and a lower output voltage ripple compared to the conventional PV emulator.</span>

Background/Purpose: The acquisition of three-dimensional ground reaction forces (3D-GRF) during running is crucial for monitoring and assessing running performance. However, limitations often arise in collecting 3D-GRF due to equipment and environmental constraints. Inertial sensors are gaining popularity in running applications because of their convenience, broad applicability, and cost-effectiveness. This study aimed to utilize an inertial sensor for gathering kinematic data during running, establish a high-precision neural network model for continuous 3D-GRF estimation, and investigate estimation variances across different body segments. Method: A total of thirty-three college students (17 male, 16 female) participated in this study. Kinematic and kinetic data were concurrently recorded using inertial sensors placed on the lower back, lateral thigh, anterior lower leg, and dorsum of the foot, while three-dimensional force plates were utilized during running at speeds of 8/10/12 km/h. The dataset was partitioned into training, validation, and test sets at a ratio of 24:3:6. A Long Short-Term Memory Neural Network (LSTM) was developed for training to predict 3D-GRF. Evaluation metrics included coefficients of determination, Root Mean Square Error (RMSE), and Normalized Root Mean Square Error (NRMSE). Models customized for specific body segments underwent a nine-fold cross-validation procedure, employing one-way ANOVA to evaluate estimation variances across different anatomical sites. Results: Estimation outcomes at different sites indicated optimal estimation accuracy at the right thigh. The coefficients of determination for Anteroposterior (AP)-GRF, Mediolateral (ML)-GRF, and Vertical (V)-GRF were 0.81±0.00, 0.55±0.14, and 0.97±0.02, respectively. RMSE values were 0.06±0.01BW, 0.06±0.01BW, and 0.14±0.03BW. Significant variances were observed between the right thigh and other sites in the horizontal plane (p < 0.05). The results from the test set showed correlation coefficients, RMSE, and NRMSE for AP-GRF, ML-GRF, and V-GRF: AP-GRF, 0.94±0.01, 0.06±0.01BW, 4.78%±0.50%; ML-GRF, 0.83±0.08, 0.10±0.01BW, 9.70%±2.41%; V-GRF, 0.99±0.00, 0.14±0.02BW, 2.79%±0.24%. Conclusion/Discussion: 1. The neural network model developed in this study demonstrated exceptional accuracy across three dimensions, facilitating continuous estimation of 3D ground reaction forces during running. Correlation coefficients surpassed 0.8 in every direction, with RMSE values below 0.2BW and NRMSE below 5%. 2. Estimation results from inertial sensors positioned at different sites exhibited diverse levels of disparity. The lateral thigh emerged as the most proficient location for estimation, with the lower back excelling in vertical ground reaction force estimation but displaying comparatively weaker performance in horizontal ground reaction force estimation.

Time-varying wind conditions, on which wind turbines depend, significantly influence power generation performance. Accordingly, this study proposes an approach to improve the accuracy of wind power generation prediction by incorporating time-varying wind conditions into the OpenFAST wind turbine model. An OpenFAST wind turbine model was constructed using wind speed and wind direction data collected from the weather station near the wind farm. The numerical model was composed of cases where only wind speed was considered and cases where the time-varying wind direction was considered. And the hourly and daily power generation prediction results were compared and analyzed with the actual power generation through indicators such as correlation coefficient, RMSE (Root Mean Square Error) and NRMSE (Normalized Root Mean Square Error). As a result, in the model that reflects time-varying wind direction, errors were reduced and linear correlation was improved, both in comparison with actual power generation. Therefore, it can be concluded that this model enhances the accuracy of power generation prediction. Consequently, this study highlights the importance of considering time-varying wind direction in OpenFAST wind turbine simulation.