Design of an improved successive approximation type ADC using multi bit per cycle algorithm for conversion rate improvement

In this paper, we study on the automatic gain control (AGC) scheme for pulse amplitude modulation (PAM) with 1.8-V 10-bit 100MS/s successive approximation register (SAR) analog-to-digital converter (ADC) analog-to-digital converters (ADCs) by TSMC 0.18-um CMOS process. For M-PAM networked control systems, this design investigate the problem of AGC schemes under the assumption that applied ten comparators followed by an asynchronous trigger logic, the proposed SAR ADC achieves high speed operation are used at the receiver end. Compared to the conventional SAR ADC, there is no significant delay in the digital feedback logic on robotic wireless control system. With the sampling rate limited only by the ten delays of the capacitor DAC settling and comparators quantization. For of the fixed threshold ADCs, and altering the gain to ADC input, we propose an algorithm based on ADC output's distribution-function to adjust the gain of the amplifier in front of the ADC.

An ultra-low power consumption two-stage mixed switching scheme for successive approximation register (SAR) analog-to-digital converter (ADC) is presented. Using two simple switches, the novel switching scheme divides the capacitor arrays into two sub-arrays: stage-one and stage-two arrays. The two sub-arrays convert high and low bits cycles, respectively. Once the high bits conversion cycles are completed, the corresponding sub-arrays are split off from the capacitor arrays. This decreases the number of capacitors used in the rest conversion procedure. Thus, the proposed method improves the energy efficiency of SAR ADC. Thanks to C–2C dummy capacitors and two-stage capacitor arrays, the novel architecture achieves 86% reduction in capacitor area than conventional SAR ADC. Furthermore, based on the charge sharing technique and monotonic switching method, the proposed switching scheme does not consume reset energy and achieves 99.8% less switching energy than the conventional switching method. In addition, the proposed scheme is less sensitive to capacitor mismatch because of its great performance in linearity.

This paper presents a new single channel 6-bit 900MS/s asynchronous binary search analog to digital converter (ADC). The proposed ADC works based on binary search principle like the Successive Approximation Register (SAR) ADC. Compared to SAR ADC the speed is improved significantly adopting two design techniques. By implementing the binary search in an open loop configuration using asynchronous clock generation the delay in the feedback path of the SAR ADC is relaxed significantly. Moreover in the proposed asynchronous binary search ADC two bits are resolved in each stage of the ADC. By resolving two bits in each stage the proposed ADC can operate twice as fast as conventional asynchronous binary search ADCs. The proposed single channel 6-bit 900MS/s ADC was designed in 90nm CMOS process. Simulation results show that the proposed ADC reaches a peak SNDR of 35.82dB consuming 4.33mW from a single 1.2V power supply. It achieves of 95.3fJ/conv.code FoM.

In this work, a switched capacitor-based successive approximation register (SAR) analog-to-digital converter (ADC) using a passive reference charge sharing and charge accumulation is proposed. For N-bit resolution, the fully differential version of this architecture needs only 6 capacitors, which is a significant improvement over conventional binary-weighted SAR ADC. The proposed SAR ADC is first modeled in MATLAB, and the effect of practical operational transconductance amplifier limitations such as finite values of gain, unity-gain bandwidth and slew rate on ADC characteristics is verified through behavioral simulations. To validate the proposed ADC performance, an 11-bit 2 kS/s SAR ADC is designed and laid out in UMC 180 nm 1P6M CMOS technology with a supply voltage of 1.8 V. The total design occupies an area of $$568\,\upmu \hbox {m} \times 298\,\upmu \hbox {m}$$ and consumes a power as less as $$0.28\,\upmu \hbox {W}$$ . It is found that the integral nonlinearity and differential nonlinearity of this ADC are in the range + 0.35/− 0.84 least significant bit (LSB) and + 0.1/− 0.6 LSB, respectively. In addition, dynamic performance test shows that the proposed SAR ADC offers an effective number of bits of 10.14 and a Walden figure of merit (FoMW) of 0.12 pJ/conv-step.

An energy-efficient DAC switching algorithm based on charge recycling method for SAR ADCs

This work presents a 12 bit 200 MS/s dual-residue pipelined successive approximation registers (SAR) analog-to-digital converter (ADC) with a single open-loop residue amplifier (RA). By using the inherent characteristics of the SAR conversion scheme, the proposed ADC sequentially generates two residue levels from the single RA, which eliminates the need for inter-stage gain-matching calibration. To convert the sequentially generated the two residues, a capacitive interpolating SAR ADC (I-SAR ADC) is also proposed. The I-SAR ADC is very compact because it consists of the one comparator, a CDAC, and control logic like a conventional SAR ADC. In addition, the I-SAR ADC needs no static power dissipation for the residue interpolation. A prototype ADC fabricated in a 40 nm CMOS technology occupies an active area of 0.026 mm2. At a 200 MS/s sampling-rate with the Nyquist input, the ADC achieves an SNDR (Signal-to-Noise distortion ratio) of 62.1 dB and 67.1 dB SFDR (Spurious-Free Dynamic Range), respectively. The total power consumed is 3.9 mW under a 0.9 V supply. Without any inter-stage mismatch calibration, the ADC achieve Walden Figure-of-Merit (FoM) of 19.0 fJ/conversion-step.

In recent years and continuing, widespread research work is carried out on medical implantable devices placed inside the human body. The essential and vital electronic circuit in implantable devices is the Analog to Digital Converter (ADC). The essential requirements in these applications such as long battery life-time, low power consumption and less die area poses a stringent requirement in designing and fabricating an ultra-low power ADCs. Among the diverse converter architectures existing, Successive Approximation Register (SAR) type converter architecture has shown better capabilities in terms of ultra-low power operation, medium resolution, less form factor and less silicon area. In this described paper a novel power effective, better resolution SAR type ADC to be used for biomedical related applications. The proposed work consists of capacitive type Digital to Analog Converter (DAC) based on charge distribution, a CMOS comparator, and SAR logic implemented using D-flip-flops. The different blocks of SAR architecture are simulated using EDA tools in CMOS 180 nm N-well process operated at VDD = 1.5 V voltage (VDD). The circuit is measured under various input frequencies with a sampling speed of 50 MHz and it consumes 22.6 μW. The proposed ADC technology shows SNDR of 48.6 dB and occupies a circuit area of 0.11 mm2 and the measured INL and DNL is calculated to be fewer than 0.54 LSB and 0.45 LSB respectively.

Digital to Analog Converter (DAC) is the essential block to convert an input digital signal into analog signal. The switching technique is the important parameter that will affect the performance of DAC where to ensure the analog output signal can be obtained without any missing code. The capacitor DAC is most famous architecture used to design the DAC and it produce high power efficiency. But, the number of unit capacitors in DAC increase exponentially due to the increasing of resolution and a DAC block occupies a largest area among many internal blocks in Successive Approximation Register (SAR) Analog to Digital Converter (ADC). The DAC was designed for 14-bit SAr ADC using a hybrid Rc DAC architecture. The design of DAC has been carried out by using 0.18μm CMOS Silterra process Technology. The simulation results are done with 3.3V voltage supply and obtained DNL within -0.39 LSB to 0.238 LSB. It occupies an area of 0.614μm2.

In this research work a 10 bit SAR(Successive Approximation Register) type ADC(Analog to Digital Converter) IP(Intellectual Property) has been approached with some specifications along with the circuit diagram of each elementary design block. Here 180 nm technology has been used. Various types of performance parameters like area, resolution, i/p current, i/p impedance, conversion time etc. have been discussed. Also the pre-layout as well as post layout simulation results have been given in this paper.

A resolution-independent successive approximation register (SAR) analog to digital converter (ADC) architecture based on a switched capacitor integrator is presented. Digital to analog converter (DAC) architecture uses charge sharing and integration principle for reference generation, using only six unit capacitors for a fully differential version. A 10-bit, 1.8-V and 0.9-MS/s SAR ADC is designed in 180-nm CMOS process. ADC architecture is area efficient when compared with SAR ADC with a binary weighted capacitor array DAC. The architecture is largely parasitic insensitive, also programmable resolution is possible with no hardware overhead.

The design plan and HSPICE measurement of a high acquisition speed for a sample of 8-bit CMOS differential successive approximation register (SAR) Analog-to-digital converter (ADC) are presented. The operation of the conventional main switch-capacitor array is divided into two switch-capacitor arrays. Such that, one switched-capacitor array is used to define the four most-significant bits, while the other switched-capacitor array is used to refine the digital output by measuring the least four significant bits. Thus, the critical time constant, which is usually realized in a single conversion cycle, is divided into four conversion cycles (i.e. the time required to quantize the four most-significant bits). Thereby, our proposed ADC operates at 200MHz conversion cycle for a sample rate of 25 MS/sec. with power consumption of 3.7mW. The design is based on 0.25μm CMOS TSMC technology and comprises three comparator circuits, sign-comparator and two switched-capacitor arrays' comparators.

Energy consumption is very critical for environmental monitoring using wireless sensor networks, thus, every block must be designed to consume low energy to be within the limited energy budget of a sensor node. In the context of improving the power efficiency of the analog-to-digital converter (ADC), for this specific application, successive approximation register (SAR) ADC is the best architecture to use. In addition, coarse-fine technique has been proven to reduce power consumption in SAR ADCs. However, design considerations involving the coarse ADC bit allocation are important but not discussed in literature. These includes the following: trade off between resolution of the coarse stage and the accuracy of the ADC; trade off between the energy consumption, accuracy and speed of the comparator block; and trade off between energy consumption and accuracy of different switching schemes for the digital-to-analog (DAC) block. This project produced models of these trade-offs, provided a methodology in designing coarse-fine SAR ADCs, implemented two ADCs in the schematic level: the one with the lowest energy consumption; and the one with the highest Schreier figure of merit (FoMs), and implemented the ADC with the lowest energy consumption in the layout level. Optimization using the MATLAB model in the DAC lead to k = 4 which gives the lowest power and k = 3 which gives the highest Schreier FoM. Schematic implementation at 50kSps of k = 4 and k = 3 gave: 2.201pJ and 2.3617pJ switching energy; 9.2 and 9.3 ENOB; and 170.96 dB and 170.72 dB Schreier FoM, respectively. This project was also able to match the trends of the models to the simulations although there are deviations of values. However, ENOBs fall within the target range of ENOBs.

We propose a hybrid Analog to Digital Converter (ADC) combined with the first-stage as a first-order feedforward incremental (FF I-) ADC and the second-stage as a SAR (Successive Approximation Register) ADC as high-precision and high-speed ADCs. As a result of simulation, the proposed hybrid ADC correctly converts data even if capacitance in FF path of the first-order I-ADC has 10% error.

Data converters play an important role in this ever-increasing digital world, which is mainly dependent on Complementary Metal Oxide Semiconductor (CMOS) technology. Analog to Digital Converters (ADCs) are important components of the day- to day communication and signal processing area. Among ADCs, Successive Approximation Register (SAR) ADCs are mostly used in low power, high-resolution area efficient circuits. Recent development in CMOS SAR ADC is distinctive in the denomination of architecture and its performance.

This paper presents an energy efficient successive-approximation-register (SAR) analog-to-digital converter (ADC) for biomedical applications. To reduce energy consumption, a bypass window technique is used to select switching sequences to skip several conversion steps when the signal is within a predefined small window. The power consumptions of the capacitive digital-to-analog converter (DAC), latch comparator, and digital control circuit of the proposed ADC are lower than those of a conventional SAR ADC. The proposed bypass window tolerates the DAC settling error and comparator voltage offset in the first four phases and suppresses the peak DNL and INL values. A proof-of-concept prototype was fabricated in 0.18-μm 1P6M CMOS technology. At a 0.6-V supply voltage and a 200-kS/s sampling rate, the ADC achieves a signal-to-noise and distortion ratio of 57.97 dB and consumes 1.04 μW, resulting in a figure of merit of 8.03 fJ/conversion-step. The ADC core occupies an active area of only 0.082 mm2.