Detection and quantification of structural damage under ambient vibration environment

Need for developing efficient non-destructive damage detection procedures for civil engineering structures is growing rapidly. This paper presents a methodology for detection and quantification of structural damage using modal information obtained from transfer matrix technique. Vibration characteristics of beam-like structure have been determined using the computer program developed based on the formulations presented in the paper. It has been noted from reported literature that detection and quantification of damage using mode shape information is difficult and further, extraction of mode shape information has practical difficulties and limitations. Hence, a methodology for detection and quantification of damage in structure using tranfer matrix technique based on the changes in the natural frequencies has been developed. With an assumption of damage at a particular segment of the beam-like structure, an iterative procedure has been formulated to converge the calculated and measured frequencies by adjusting flexural rigidity of elements and then, the intersections are used for detection and quantification of damage. Eventhough the developed methodology is iterative, computational effort is reduced considerably by using transfer matrix technique. It is observed that the methodology is capable of predicting the location and magnitude of damage quite accurately.

Experimental study of laser Doppler vibrometer and ambient vibration for vibration-based damage detection

The ancient masonry city hall in L'Aquila, Italy (Margherita Palace) that was severely damaged during the L'Aquila earthquake in April 2009 has been subjected to ambient vibration tests to determine its dynamic characteristics such as the natural frequencies, mode shapes, and damping ratios. The processing of ambient vibration responses is performed with three output-only identification approaches: (1) the frequency-domain decomposition, (2) random decrement (RD) technique combined with the eigensystem realization algorithm (ERA), and (3) the natural excitation technique (NExT) combined with ERA. Measurements were made in the palace and in the civic tower using 15 sensors in three different configurations, and the ambient vibration tests involved the simultaneous measurements of longitudinal and lateral vibrations. Lateral vibration modes for the civic tower were identified clearly; a total of five modal shapes and frequencies were identified in the frequency range 0 to 7 Hz. The modal identification in the palace was more difficult because of the severe damage; however, the two bending modes in the perpendicular directions were identified. The comparison of the three experimental techniques shows good agreement, confirming the reliability of the three identification methods. The results of the modal identification have been used to update the finite-element model of the palace. DOI: 10.1061/(ASCE)ST.1943-541X.0000494. © 2012 American Society of Civil Engineers. CE Database subject headings: Historic buildings; Masonry; Finite element method; Vibration; Structural analysis; Earthquakes; Italy. Author keywords: Output-only modal identification; Frequency domain decomposition (FDD); Eigensystem realization algorithm (ERA); Random decrement (RD); Masonry structure; Finite-element model; Ambient vibration; Identification; EMA; Operational modal analysis.

The guided-wave-based damage detection methodology is a well-established branch of Structural Health Monitoring. There are, however, many different approaches to processing and interpretation of signals acquired using guided waves. This paper presents the results of the SYPIN project in which a large database acquired in a diverse set of experiments was assembled. The experiments included static and variable environmental conditions, composite and metallic specimens of simple and complex geometries. The set includes, in particular, results of experiments on real-life aircraft specimens. This dataset was then used to benchmark several damage detection and quantification methodologies, including various classifiers and feature extraction methods. The performance of the methods is evaluated in a series of experiments, including knowledge transfer between different specimens. The paper presents the results of this research and provides a brief description of the dataset, which is made available for the scientific community’s use.KeywordsGuided wavesBenchmarkClassificationSignal processingAircraft

This paper presents the operational modal analysis of a 90-m-high RC minaret of an iconic mosque considered as a landmark of the city. The minaret was monitored for three days with 11 tri-axial MEMS accelerometers. The purpose of the study was to observe the behavior, develop a representative finite element (FE) model, and establish baseline data for health monitoring studies. The modal properties were extracted using three operational modal analysis techniques (OMA): Enhanced Frequency Domain Decomposition (EFDD), Stochastic Subspace Identification (SSI), and Natural Excitation Technique with Eigensystem Realization Algorithm (NExT-ERA). The first 10 identified modes were below 7 Hz. Eight modes out of the ten were bending-dominant, while the remaining two were torsion-dominant. A FE model was also developed in ETABS to ascertain and compare the response of the structure with the identified results. From the FE model, the modes corresponding to the first ten identified modes were considered for comparison with the identified frequencies from ambient monitoring. The maximum 7.71% error was observed between the experimental and numerical frequencies. The error was minimized by using the manual updating the material properties and adding the weight of nonstructural elements. The variation of identified modal frequencies with ambient temperature was observed to be linearly dependent to a reasonable degree. A general trend of decreasing identified frequencies was observed with the rise in temperature.

Dynamic monitoring of an offshore jacket platform based on RTK-GNSS measurement by CF-CEEMDAN method

It is still necessary to investigate the detection of structural damage under ambient excitations since the excitations are random and unmeasured while measurement noises are inevitable. In this paper, a method based on the synthesis of cross-correlation functions of partial structural responses and the extended Kalman filter (EKF) approach is proposed for the identification and damage detection of structures under ambient excitations, in which both independent stationary and non-stationary white noise excitations in the product models are discussed. First, the equations of cross-correlation functions of structural responses are established when the ambient excitations are independent stationary white noise processes. Then, the EKF approach is utilized to identify structural parameters and cross-correlation functions using partial measurements of structural acceleration responses. Structural damage is detected based on the degradations of the identified structural element stiffness parameters. Finally, the proposed method is extended to deal with independent non-stationary white noise excitations in the product models. The numerical simulation examples of the ASCE structural health monitoring benchmark building subject to ambient excitation, a moment resisting frame model under white noise excitation, and a cantilever beam model under multiple independent non-stationary excitations are used to validate the feasibility of the proposed method. It is shown that the method is not sensitive to measurement noises. Also, a lab experimental study of the identification of a multi-story shear structure is investigated to further illustrate the applicability of the proposed method.

Structural damage detection using sparse sensors installation by optimization procedure based on the modal flexibility matrix

Structural damage detection of a cantilever beam under varying temperature using a collection of time series

In the past few decades, vibration-based structural damage detection (SDD) has attracted widespread attention. Using the response data of engineering structures, the researchers have developed many methods for damage localization and quantification. Adopting meta-heuristic algorithms, in which particle swarm optimization (PSO) is the most widely used, is a popular approach. Various PSO variants have also been proposed for improving its performance in SDD, and they are generally based on the Global topology. However, in addition to the Global topology, other topologies are also developed in the related literature to enhance the performance of the PSO algorithm. The effects of PSO topologies depend significantly on the studied problems. Therefore, in this article, we conduct a performance investigation of eight PSO topologies in SDD. The success rate and mean iterations that are obtained from the numerical simulations are considered as the evaluation indexes. Furthermore, the average rank and Bonferroni-Dunn’s test are further utilized to perform the statistic analysis. From these analysis results, the Four Clusters are shown to be the more favorable PSO topologies in SDD.

This paper presents an effective method of FE model updating for health monitoring of structures by applying ambient vibration. And this method is experimented through damage detection and proved to be valid. Experiment about ambient vibration is performed on cantilever beam, and the dynamic characteristics are analyzed by NExT and ERA. The results of such experiments are compared to those of FE analysis, and this comparison enables us to overcome some errors in experiments and analysis. On the basis of improved results by the comparison, model updating is performed in order to construct a basic structure for health monitoring. For model updating, we employ direct matrix updating method (DMUM) and Error matrix method (EMM) in which ambient vibration is easily applied. The model updating by the methods are again evaluated in terms of error ratio of natural frequency, comparing each result before and after updating. Finally, we perform experiments on damage detection to verify the method of updating presented here, and evaluate its performance by eigen-parameter change method. The evaluation proves that the method of FE model updating using ambient vibration is effective for health monitoring of structure, and some further application of this method is suggested.

In this paper, an improvement of the elliptical triangulation method for damage detection using Lamb waves is presented. The damage is the main cause of structural failure and often occurs on structures. In order to avoid sudden failure, a special attention was given in the past decades to the damage detection in structures. In order to obtain efficient damage detection techniques, the structural health monitoring has been the main research topic of many scientists worldwide. The elliptical triangulation method, proposed in this paper, is a non-destructive method based on measurement of Lamb waves. This method, through the calculation of the time of flight of the signals and the actuator-sensor positioning, allows to identify position and dimension of the damage. The application of the method to the metallic structures and to the composite material structures is presented in this paper. The complexity connected with the uncertainty of the waves’ propagation speed due to the anisotropy of the composite materials has been explored through an iterative approach. The initialization of the wave propagation speed at first tentative iteration is the key issue for the convergence of the method. Seven different conditions were used to validate the method on both metallic and composite structures combining two damage shapes, two damage dimensions (effective damaged area), and three different positions. Upon evaluating the effectiveness, the method has been applied at two composite panels in order to detect by test the post-impact damages. Tests results have been compared with the numerical ones. The feasibility of the elliptical triangulation method to detect the damage (evaluating the damage position and area) has been proved using the ultrasonic C-Scan.

Nondestructive evaluation (NDE) for detection and quantification of damage in composite materials is fundamental in the assessment of the overall structural integrity of modern aerospace systems. Conventional NDE systems have been extensively used to detect the location and size of damages by propagating ultrasonic waves normal to the surface. However they usually require physical contact with the structure and are time consuming and labor intensive. An automated, contactless laser ultrasonic imaging system for barely visible impact damage (BVID) detection in advanced composite structures has been developed to overcome these limitations. Lamb waves are generated by a Q-switched Nd:YAG laser, raster scanned by a set of galvano-mirrors over the damaged area. The out-of-plane vibrations are measured through a laser Doppler Vibrometer (LDV) that is stationary at a point on the corner of the grid. The ultrasonic wave field of the scanned area is reconstructed in polar coordinates and analyzed for high resolution characterization of impact damage in the composite honeycomb panel. Two methodologies are used for ultrasonic wave-field analysis: scattered wave field analysis (SWA) and standing wave energy analysis (SWEA) in the frequency domain. The SWA is employed for processing the wave field and estimate spatially dependent wavenumber values, related to discontinuities in the structural domain. The SWEA algorithm extracts standing waves trapped within damaged areas and, by studying the spectrum of the standing wave field, returns high fidelity damage imaging. While the SWA can be used to locate the impact damage in the honeycomb panel, the SWEA produces damage images in good agreement with X-ray computed tomographic (X-ray CT) scans. The results obtained prove that the laser-based nondestructive system is an effective alternative to overcome limitations of conventional NDI technologies.

Two-stage structural damage detection using fuzzy neural networks and data fusion techniques

Detecting structural damage in operational conditions still encounters some difficulties, especially in early-stage, as environmental varieties impose challenges in real engineering applications and may require large computational efforts in the structural health monitoring and potential maintenance. Unlike conventional strategies employing frequency response function or response data, a damage detection methodology is addressed in this study by employing transmissibility functions that retains a strong interrelation with structural damage or deterioration, in order to avoid the measurement of excitation, together with principal component analysis that leads to reduction in computational costs. In this procedure, transmissibility is extracted from the structural responses and main features are selected by principal component analysis for less computational costs. Then, via distance measures damage indicators are constructed for both intact and damaged states, and finally a numerical simulation with a clamped-clamped beam and a four-story benchmark are adopted to verify the applicability of the proposed procedure. The results demonstrate a good performance in structural damage detection.