Development of a framework for sequential Bayesian design of experiments: Application to a pilot-scale solvent-based CO<sub>2</sub> capture process

Development of a framework for sequential Bayesian design of experiments: Application to a pilot-scale solvent-based CO2 capture process

Sequential Design of Experiments to Maximize Learning from Carbon Capture Pilot Plant Testing

The paper considers a sequential Design Of Experiments (DOE) scheme. Our objective is to maximize both information and economic measures over a feasible set of experiments. Optimal DOE strategies are developed by introducing information criteria based on measures adopted from information theory. The evolution of acquired information along various stages of experimentation is analyzed for linear models with a Gaussian noise term. We show that for particular cases, although the amount of information is unbounded, the desired rate of acquiring information decreases with the number of experiments. This observation implies that at a certain point in time it is no longer efficient to continue experimenting. Accordingly, we investigate methods of stochastic dynamic programming under imperfect state information as appropriate means to obtain optimal experimentation policies. We propose cost-to-go functions that model the trade-off between the cost of additional experiments and the benefit of incremental information. We formulate a general stochastic dynamic programming framework for design of experiments and illustrate it by analytic and numerical implementation examples.

This study describes the use of an analytical model, constructed using sequential design of experiments (DOEs), to optimize and quantify the uncertainty of a Diesel engine operating point. A genetic algorithm (GA) was also used to optimize the design. Three engine parameters were varied around a baseline design to minimize indicated specific fuel consumption (ISFC) without exceeding emissions (NOx and soot) or peak cylinder pressure constraints. An objective merit function was constructed to quantify the strength of designs. The engine parameters were start of injection (SOI), injection duration, and injector included angle. The engine simulation was completed with a sector mesh in the commercial computational fluid dynamics (CFD) software CONVERGE, which predicted the combustion and emissions using a detailed chemistry solver with a reduced mechanism for n-heptane. The analytical model was constructed using the SmartUQ software using DOE responses to construct kernel emulators of the system. Each emulator was used to direct the placement of the next set of DOE points such that they improve the accuracy of the subsequently generated emulator. This refinement was either across the entire design space or a reduced design space that was likely to contain the optimal design point. After sufficient emulator accuracy was achieved, the optimal design point was predicted. A total of 5 sequential DOEs were completed, for a total of 232 simulations. A reduced design region was predicted after the second DOE that reduced the volume of the design space by 96.8%. The final predicted optimum was found to exist in this reduced design region. The sequential DOE optimization was compared to an optimization performed using a GA. The GA was completed using a population of 9 and was run for 71 generations. This study highlighted the strengths of both methods for optimization. The GA (known to be an efficient and effective method) found a better optimum, while the DOE method found a good optimum with fewer total simulations. The DOE method also ran more simulations concurrently, which is an advantage when sufficient computing resources are available. In the second part of the study, the analytical model developed in the first part was used to assess the sensitivity and robustness of the design. A sensitivity analysis of the design space around the predicted optimum showed that injection duration had the strongest effect on predicted results, while the included angle had the weakest. The uncertainty propagation was studied over the reduced design region found with the sequential DoE in the first part. The uncertainty propagation results demonstrated that for the relatively large variations in the input parameters, the expected variation in the ISFC and NOx results were significant. Finally, the predictions from the analytical model were validated against CFD results for sweeps of the input parameters. The predictions of the analytical model were found to agree well with the results from the CFD simulation.

This work, under the optimal experimental design framework, investigates the sensor placement problem that aims to guide electromagnetic induction (EMI) sensing of multiple objects. We use the linearized model covariance matrix as a measure of estimation error to present a sequential experimental design (SED) technique. The technique recursively minimizes data misfit to update model parameters and maximizes an information gain function for a future survey relative to previous surveys. The fundamental process of the SED seeks to increase weighted sensitivities to targets when placing sensors. The synthetic and field experiments demonstrate that SED can be used to guide the sensing process for an effective interrogation. It also can serve as a theoretic basis to improve empirical survey operation. We further study the sensitivity of the SED to the number of objects within the sensing range. The tests suggest that an appropriately overrepresented model about expected anomalies might be a feasible choice.

마이크로 유전알고리즘은 적은 수의 개체 사용 및 무작위 개체 구성을 통한 돌연변이 기능 대체의 특징을 갖는 진화연산을 수행하여 일반적인 유전알고리즘이 갖는 각 세대당 많은 계산 량이 요구되는 단점을 극복하고자 하였다. 이러한 마이크로 알고리즘은 특히 설계변수가 3~5 개를 갖는 문제에 효율적이라는 것이 많은 연구자들에 의하여 알려졌다. 따라서 본 연구의 목적은 순차적 실험계획법과 마이크로 유전알고리즘을 이용한 최적화 알고리즘을 개발하는 것이며, 이를 수학예제와 구조물 문제에 적용하여 실용성을 확인하고자 한다. 순차적 실험계획법은 저자들의 선행연구에서 제안되었으며, 실험계획법과 반응표면법을 이용하는 근사최적화 기법에 의한 시행착오적인 반복과정을 최소화하고자 하는 방법으로써, 행렬실험과 평균분석을 반복 적용하는 개념이다.

The National Carbon Capture Center (NCCC) at the Power Systems Development Facility supports the Department of Energy (DOE) goal of promoting the United States’ energy security through reliable, clean, and affordable energy produced from coal. Work at the NCCC supports the development of new power technologies and the continued operation of conventional power plants under CO2 emission constraints. The NCCC includes adaptable slipstreams that allow technology development of CO2 capture concepts using coal-derived syngas and flue gas in industrial settings. Because of the ability to operate under a wide range of flow rates and process conditions, research at the NCCC can effectively evaluate technologies at various levels of maturity and accelerate their development path to commercialization. During its first contract period, from October 1, 2008, through December 30, 2014, the NCCC designed, constructed, and began operation of the Post-Combustion Carbon Capture Center (PC4). Testing of CO2 capture technologies commenced in 2011, and through the end of the contract period, more than 25,000 hours of testing had been achieved, supporting a variety of technology developers. Technologies tested included advanced solvents, enzymes, membranes, sorbents, and associated systems. The NCCC continued operation of the existing gasification facilities, which have been in operation since 1996, to support the advancement of technologies for next-generation gasification processes and pre-combustion CO2 capture. The gasification process operated for 13 test runs, supporting over 30,000 hours combined of both gasification and pre-combustion technology developer testing. Throughout the contract period, the NCCC incorporated numerous modifications to the facilities to accommodate technology developers and increase test capabilities. Preparations for further testing were ongoing to continue advancement of the most promising technologies for future power generation processes.

This study aims to optimize the variables involved in the wool dyeing process with cochineal (Dactylopius coccus Costa) to achieve the Mexican red hue, providing a scientific guide in the production of cochineal-dyed textiles. Sequential experimental designs and the steepest ascent method were employed to evaluate key factors, including insect quantity, mordant quantity, toner quantity, dyeing temperature, dyeing time, mordanting method, and dye pot material, by using color strength (K/S) maximum (at 530 nm) as a response variable. Colorimetric measurements were made in the CIELab color space for shade confirmation. The results highlighted the importance of pre-mordanting (using alum) and identified insect and toner quantities as the most significant variables. An optimal plateau was identified within the range of (45–55)% on weight of fabric (owf) for insect quantity and (20–25)% owf for toner (cream of tartar) quantity. Wash fastness tests demonstrated good to very good performance, with grayscale ratings of 3–4, and minimal to no staining on adjacent fabrics.

Surrogate-based sequential Bayesian experimental design using non-stationary Gaussian Processes

On the costs of parameter uncertainties. Effects of parameter uncertainties during optimization and design of experiments

Conducting new experiments for biomass gasifiers is expensive and time consuming. Therefore, it is important to select conditions for new experiments so maximum information is obtained. In this study, sequential Bayesian model-based design of experiments (MBDoE) is used to design new experimental runs for a heat-integrated biomass downdraft gasifier. This MBDoE approach is valuable because it accounts for model structure, prior information about plausible parameter values, and previous experimental data in a relatively simple way. Operating conditions selected for each new run are biomass moisture content, water injection rate, and the desired energy demand from the downstream engine. Three types of MBDoE with different objective functions are considered: A-optimal, V-optimal, and a proposed new type of focused V-optimal design. A-optimal design is used to when the goal is to obtain improved parameter estimates, without specifying how the model will be used. Performing two new A-optimal runs reduced the standard deviations for model parameters by 18.4% on average compared to when only old data are available. The three most-improved parameter estimates are activation energies for char gasification reactions involving carbon dioxide, hydrogen, and steam, respectively. The focused V-optimal methodology results in greater improvements in prediction accuracy for tar concentration and outlet temperature, which are key model responses. Using two designed Vf-optimal runs reduces standard deviations for these variables by 59.4%, on average, compared to when only old data are available. New A-optimal and V-optimal runs lead to corresponding improvements of 30.7% and 50%, respectively.

Sequential sampling refers to a set of design of experiment (DOE) methods where the next sample point is determined by information from previous experiments. This paper introduces a qualitative and quantitative sequential sampling (Q2S2) technique, in which optimization and user knowledge is used to guide the efficient choice of sample points. This method combines information from multiple fidelity sources including computer simulation models of the product, first principals involved in design, and designer’s qualitative intuitions about the design. Both quantitative and qualitative information from different sources are merged together to arrive at a new sampling strategy. This is accomplished by introducing the concept of a confidence function, C, which is represented as a field that is a function of the decision variables, x, and the performance parameter, f. We compare the sampling plans generated by Q2S2 to previously known sample plans on five test functions using various metrics. In each case, the performance of Q2S2 is highly encouraging.

Microbial bioprospecting in contaminated environments is a promising strategy for identifying biosurfactant-producing bacteria; however, translating environmentally adapted strains into predictable cultivation processes remains challenging. In this study, a microbial consortium subjected to long-term evolutionary laboratory adaptation in oily sludge was investigated to evaluate strain-specific phenotypic responses related to biosurfactant production. Phylogenetic analysis based on 16S rDNA sequencing identified three taxonomically distant isolates: Faucicola sp. strain BS5C, Pseudomonas sp. strain BS16B, and Enterobacter sp. BS14MR. Biosurfactant production was evaluated using a sequential Design of Experiments (DOE) approach, including fractional factorial and central composite rotatable designs, with the emulsification index (E24) used as a semi-quantitative response variable. Initial screening revealed a statistically significant negative effect (p < 0.10) of high dextrose concentrations for all isolates. Strain-specific differences in model adequacy were observed, with a statistically adequate quadratic model obtained for Pseudomonas sp. BS16B (R2 = 0.8658, p = 0.0225), whereas the other isolates showed significant lack of fit (p < 0.05). ATR-FTIR analysis revealed spectral profiles consistent with lipopeptide-like compounds. Overall, these results indicate that isolates derived from the same long-term adapted system may differ substantially in process predictability, suggesting that productivity-based screening alone may be insufficient for selecting robust strains.

This paper discusses a new sequential adaptive design of experiments (DoE) approach for global Kriging metamodeling applications. The sequential implementation is established by using the current metamodel, formulated based on the existing experiments, to guide the selection of the optimal new experiment(s). The score function, defining the DoE objective, combines two components: (1) the metamodel prediction variability, expressed through the predictive variance, and (2) the metamodel bias, approximated through the leave-one-out cross validation (LOOCV) error. The latter is used as a weighting factor to extend traditional DoE approaches that focus solely on the metamodel prediction variability. Two such approaches are considered here, adopting either the integrated mean squared error or the maximum mean squared error as the basic component of the score function. The incorporation of bias information as weighting within these well-established approaches facilitates a direct extension of their respective computational workflows, making the proposed implementation attractive from computational perspective. An efficient optimization scheme for identification of the next experiment, as well as the balancing of exploration and exploitation between the two components of the score function, are also discussed. The incorporation of LOOCV weightings is shown to be highly beneficial in a total of six analytical and engineering examples. Furthermore, these examples demonstrate that for DoE approaches which use LOOCV information as weights, it is preferable to update the predictive variance to explicitly consider the impact of the new experiment, rather than relying strictly on the current metamodel variance.

15th 18th March 2021 Abu Dhabi, UAE Effects of carbon treating on piperazine oxidation in pilot plant testing of PZASTM