Development of mode converters for 28 GHz electron cyclotron heating system

The results of a detailed theoretical study on collinear guided wave to leaky wave acoustooptic (AO) interactions in proton-exchanged LiNbO(3) (PE:LiNbO(3)) planar waveguides are presented. The guided-to-leaky mode conversion for an input optical beam at the wavelength of 632.8 nm by the induced diffraction grating from a collinear surface acoustic wave (SAW) is analyzed using a generalized multimode formulation of the coupled mode theory. Mode conversion efficiency and AO bandwidth have been calculated as functions of acoustic frequency, interaction length, guiding layer thickness, and acoustic drive power density for three cuts of the LiNbO(3) substrate. High performance configurations that are desirable for application to demultiplexing and switching in optical communication systems are identified, and the corresponding channel capacity and frequency resolution are determined. For example, it was shown that the X-cut configuration features the highest mode conversion efficiency. However, a relatively small AO bandwidth is associated with this configuration. Both high mode conversion efficiency and large AO bandwidth can be accomplished at the guiding layer thickness of 1.0 microm. A TM(o)-->TE(nu) mode conversion efficiency as high as 42% together with an AO bandwidth of approximately 70 MHz can be achieved in the Z-cut waveguide at the guiding layer thickness of 1.0 microm, acoustic drive power density of 50 mW/mm, interaction length of 40 mm, and acoustic frequency of 460 MHz. The corresponding channel capacity and frequency resolution are 745 and 0.09 MHz, respectively. Measured mode conversion efficiencies as high as 90 and 78% obtained at the acoustic frequencies of 107 and 367 MHz using the X-cut substrate and the Y-propagation SAW have verified the theoretical prediction on the mode conversion efficiencies.

Mode-converted electron Bernstein waves (EBWs) potentially allow the measurement of local electron temperature (Te) and the implementation of local heating and current drive in spherical torus (ST) devices, which are not directly accessible to low harmonic electron cyclotron waves. This paper reports on the measurement of X-mode radiation mode-converted from EBWs observed normal to the magnetic field on the midplane of the Current Drive Experiment-Upgrade (CDX-U) and the National Spherical Torus Experiment (NSTX) spherical torus plasmas. The radiation temperature of the EBW emission was compared to Te measured by Thomson scattering and Langmuir probes. EBW mode-conversion efficiencies of over 20% were measured on both CDX-U and NSTX. Sudden increases of mode-conversion efficiency, of over a factor of three, were observed at high-confinement-mode transitions on NSTX, when the measured edge density profile steepened. The EBW mode-conversion efficiency was found to depend on the density gradient at the mode-conversion layer in the plasma scrape-off, consistent with theoretical predictions. The EBW emission source was determined by a perturbation technique to be localized at the electron cyclotron resonance layer and was successfully used for radial transport studies. Recently, a new in-vessel antenna and Langmuir probe array were installed on CDX-U to better characterize and enhance the EBW mode-conversion process. The probe incorporates a local adjustable limiter to control and maximize the mode-conversion efficiency in front of the antenna by modifying the density profile in the plasma scrape-off where fundamental EBW mode conversion occurs. Initial results show that the mode-conversion efficiency can be increased to {approximately}100% when the local limiter is inserted near the mode-conversion layer. Plans for future EBW research, including EBW heating and current-drive studies, are discussed.

In this paper, a compact, high efficiency TM <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> to TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">11</sub> mode converter is presented. In the proposed structure, dielectric material is loaded below a tapered centre conductor, in lower section of a circular waveguide. The input TM <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">01</sub> mode is initially transformed to TEM mode by the tapered centre conductor. The loaded dielectric material is designed to provide the desired phase shift for the mode conversion. Different dielectric materials are analyzed for loading to achieve high conversion efficiency and wide bandwidth. The proposed mode converter is fabricated with PTFE as dielectric for mode conversion and the results are verified through far field radiation pattern measurements. The mode conversion efficiency is more than 90% for 2.95-3.60 GHz band. Due to compactness and high conversion efficiency for wide bandwidth, it is suitable for S-band high power microwave (HPM) applications.

Dissipative solitons (DSs), which are pulses with high pulse energy and a broad rectangular output spectrum, have several applications. In a fiber system, the generation of higher-order DS requires a mode converter with a high and flat conversion efficiency that can cover the working waveband. The requirements on high and flat conversion efficiency as well as broadband working waveband is a great challenge for a traditional mode converter. This study presents an L-band mode-locked fiber laser with a 3-dB bandwidth of more than 47 nm and a first-order cylindrical vector (CV) mode DS output based on an ultra-broadband long-period fiber grating (LPFG). The fabricated mode converter is a novel cascading LPFG with an ultra-broadband working bandwidth and flat conversion efficiency which could meet the demand of DS mode conversion. The 15-dB bandwidth is 149.76 nm, from 1515.36 nm to 1665.12 nm. Furthermore, the conversion efficiency in the range of the output spectrum is 98.60 ± 0.23%. The single-, double-, and triple-soliton output characteristics and their real-time spectra are observed using time-stretched dispersion Fourier transformation (TS-DFT) technology. Experimental results demonstrate that the first-order CV mode DS laser can maintain its dynamics after mode conversion under the accuracy of detection system, implying that the LPFG works only as a mode converter. The broadband DS laser with CV mode output in the L-band has been presented for the first time in study, to the best of our knowledge. This study is also the first to detect real-time characteristics for a higher-order mode-locked fiber laser using the TS-DFT technology. The proposed type of LPFG is s good candidate for generating higher-order mode lasers with an all-fiber structure.

Computational inverse design techniques have shown potential to become reliable means for designing compact nanophotonic devices without compromising the performance. Much effort has been made to reduce the computation cost involved in the optimization process and obtain final designs that are robust to fabrication imperfections. In this work, we experimentally demonstrate TE0-TE1 and TE1-TE3 mode converters (MCs) on the silicon-on-insulator platform designed using the computationally efficient shape optimization method. These MCs have mode conversion efficiencies above 95%, and the insertion loss ranges from 0.3 dB to 1 dB over a wavelength span of 80 nm ranging from 1.5 µm to 1.58 µm. Maximum modal crosstalk found experimentally in the C-band is -19 dB. The conversion efficiency drops at most by 2.2% at 1.55 µm for 10 nm over/under etch, implying good robustness to dimensional variations. We present the mode conversion mechanism of these MCs by studying the simulated electromagnetic field patterns and validate with supportive data. We also demonstrate their performance in the time domain with a 28 Gbps OOK and a 20 GBaud PAM-4 payload transmissions, which supports their utility for high throughput data communications. The open eye diagrams exhibit Q-factors of 8 dB.

Ultra-compact mode converter based on longitudinal refractive index modulation

We proposed a new type of transverse electric (TE) polarized mode-order converter based on a deeply-etched polygonal slot on a silicon-on-insulator waveguide. Along the transverse direction of the waveguide, two irregular boundary surfaces of the slot can introduce high-contrast index modulation on guided modes, leading to multimode interference in the slot. Therefore, when the slot is optimized, we can achieve efficient mode conversions based on the multimode interference. As examples, mode converters from the fundamental TE mode (TE0) to the first-order TE mode (TE1) and to the second-order TE mode (TE2) have both been demonstrated with a short device length ( μ m), a high mode conversion efficiency (>97.6%), and a low modal crosstalk (< −20.0 dB) over a broad wavelength range from 1500 to 1600 nm (∼100 nm). In addition, based on different polygonal slots, other types of mode conversions such as from TE1 to TE3 and from TE2 to TE1 have be realized. Fabrication tolerance of the proposed structure is analyzed. Owing to the high efficiency and compact size, the proposed structure could be applied to on-chip mode division multiplexing systems for high-density integration.

In this paper, a dielectric-filled circular waveguide TM01-TE11 mode converter is proposed, which has high conversion efficiency and a wide operating bandwidth. Filling the circular waveguide with dielectric material changes the local propagation characteristics, thus achieving a phase difference between the TE11 modes in the two halves of the circular waveguide during propagation. This, in turn, facilitates the completion of mode conversion with high efficiency. Compared with the conventional radial dielectric plate, this paper improves the method of filling the dielectric inside the circular waveguide by transforming it into a coaxial structure. This is followed by the incorporation of a radial dielectric plate, a modification that has been proven to enhance the conversion efficiency and extend the operational bandwidth. The mode converter operates at 9.7 GHz, and when the dielectric filler material is polytetrafluoroethylene (PTFE), both simulation and practical studies are carried out. The simulation results demonstrate that the maximum conversion efficiency of this mode converter is 99.2%, and the bandwidth with conversion efficiency greater than 90% is nearly 21.1%. The maximum conversion efficiency in the actual test is essentially consistent with the simulation results. The validity of the design scheme of this converter and the accuracy of the simulation study are demonstrated.

Using the concept of a metallic cylinder and a linearly tapered metallic baffle loaded in a circular waveguide to convert TM02 circular waveguide mode into TE11 circular waveguide mode, a novel and compact circular waveguide TM02-TE11 mode converter is designed, fabricated, and measured. The detailed design methods, experimental setups and results are presented in this study. Simulation results show that the purity of output fundamental TE11 mode of the converter exceeds 99.6% for an operating frequency of 9.4 GHz and the power capability is as high as 1.66 GW, the mode conversion efficiency is more than 90% from 9.23 to 9.83 GHz band and the relative bandwidth is about 6.38%. A good agreement between measurements and simulations is observed. The circular waveguide TM02-TE11 mode converter has many advantages, such as the simple structure, coaxial input and output, high conversion efficiency, proper bandwidth and high power-handling capability. When used in the field of high power microwave transmission and radiation, the proposed converter could significantly enhance the compactness of all the radiation systems.

Two-mode converters at 1.3 μm, aiming at applications in mode-division multiplexing in Ethernet systems, are proposed and experimentally demonstrated. Based on multimode interference couplers, the two-mode converters with 50% and 66% mode conversion efficiencies are designed and fabricated on InP substrates. Mode conversion from the fundamental mode (TE0) to the first order mode (TE1) is successfully demonstrated within the wavelength range of 1280–1320 nm. The 1.3-μm mode converters should be important devices in mode-division multiplexing systems in Ethernet systems.

The mode converter, as a passive mode conversion device in transmission lines, is well-investigated and widely implemented in various electromagnetic systems. However, most traditional mode converters can only realize a single conversion mode. Thus, a mode converter achieving multiple controllable output modes is urgently needed. In this paper, a reconfigurable mode converter operating in the microwave range is achieved by embedding a deformable all-dielectric material with quadrilateral shape into a rectangular waveguide based on coupled-mode theory. It can achieve different target modes with controllable output for the same input by exciting the deformable all-dielectric material. The design principle of the mode converter is expounded concretely and simulation is carried out using HFSS software 2022 R2. Experimental results, consisting of the simulation results, demonstrate that the proposed mode converter can achieve various mode conversions with mode purity higher than 95%. This article innovatively applies deformable materials to waveguide mode conversion, expanding the application of deformable memory materials in electromagnetic devices.

Gyrotrons are sources of high-power millimeter waves. Current interest in gyrotrons is mainly because they can act as a source of microwave power for electron-cyclotron-resonance heating (ECRH) for fusion experiments. However, the field pattern of these gyrotron modes is unsuitable for long path waveguide transmission or plasma heating. Here, it is desired to have a linearly polarized wave requiring the use of a mode conversion system which consists of many nonuniform waveguide components. Based on the theory of mode coupling, this paper discusses the circular waveguide mode conversion with waveguide axis curved and radius tapered in detail. It also carries out the optimized analysis about the geometry structure of TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">0n</sub> -TE <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">11</sub> mode converter. Adopting different phase rematch techniques, the optimal geometry parameter can be obtained. The mode converter designed in this way owns high conversion efficiency exceeding 98%.

In this paper, a novel X-band TM01–TE01 mode converter for high-power microwave (HPM) system is proposed. To realize the compact design, a helical corrugated waveguide with large deformation is employed to convert the TM01 mode into TE01 mode. By optimizing the structure parameters, the simulation results demonstrate that the maximum conversion efficiency of the proposed TM01–TE01 mode converter reaches 98.8% at 9.2 GHz. Moreover, this mode converter exhibits a conversion efficiency of over 95% in the operation band from 8.7 to 9.42 GHz, and the power capacity of the mode converter reaches GW-level in theory. More importantly, the overall longitudinal and transverse dimensions of the mode converter are less than three wavelengths. The results show the compact structure and high conversion efficiency of this mode converter, which has great potential application value in the HPM system.

A mode conversion from the TE 10 in WR3 rectangular waveguide to the TE 53 in an oversized circular waveguide is required to perform the cold test of a Bragg resonator for a high power 250 GHz Cyclotron Auto-Resonance Maser (CARM) under development at the Frascati ENEA research centre. High operating frequency and oversized cylindrical cavity (exceeding any previous CARM experiment) make the design particularly challenging. An initial transition, aimed at transforming the TE 10 in WR3 rectangular waveguide into the TE 11 , in a circular waveguide, is performed using a linear taper, a well-assessed device. Then a serpentine mode converter in circular waveguide with average radius of 1.48 mm and appropriate length has been adopted for the conversion into the TE 01 mode. The subsequent transducers, for not-rotating (TE 0m ) and rotating (TE 53 ) modes, are provided by means of rippled wall mode converters with small periodic perturbations of waveguide radius. The ripple period corresponds approximately to the beat wavelength (X b = 2π/(β m − β n )) with β m and β n the wavenumbers of the two interacting modes. For not-rotating modes an efficient conversion has been obtained by cascading single step TE 01 to TE 02 , TE 02 to TE 03 and TE 03 to TE 04 mode converters. For each of them, profiles, radius and number of periods have been optimized in order to obtain low levels of unwanted spurious modes, low reflection and sufficient bandwidth. As the modes to convert (TE 04 to TE 53 ) present similar wavenumbers, the most appropriate method for the conversion consists in a three-periods rippled-wall mode converter made by a helically corrugated waveguide with an average radius of 4 mm and five azimuthal variations. The longitudinal profile of the ripples has been properly smoothed to avoid steps between the circular waveguide and the corrugated converter. In this paper the conversion chain will be described and the simulation results (S-parameters, efficiency and electric field) of each single converter will be reported. Finally some considerations about the high precision micromachining technique to be used, such as copper electroforming and Computer Numerically Controlled (CNC) milling, for the construction of these high frequency components, will be presented.

An S‐band sectoral waveguide (SWG) mode converter was presented for simulation and electromagnetic analysis. A mode‐matching technique (MMT) for the electromagnetic analysis of an SWG mode converter has been proposed. The problem of trifurcation of the coaxial waveguide to shape SWGs and bifurcation of SWGs is discussed. In this framework, the selections of appropriate testing modes at each junction are justified. The simulation time has improved and the complexity of the proposed problem has reduced by the proposed approach. The numerical results of the MMT are compared against simulation results and are found to be in good agreement. The efficiency of both the simulated and analyzed results shows a mode conversion efficiency higher than 98.0%. An experimental evaluation shows the mode conversion of TM01 to TE11 mode using far‐field radiation patterns and has been compared with simulation results. Also, the MMT and simulation validate the mode conversion of TM01 to TE11 mode.