Distributed Correlative Power Control Schemes for MobileAd hocNetworks Using Directional Antennas

Over the past few years, mobile networks have emerged as a promising approach for future mobile IP applications. With limited frequency resources, designing an effective MAC (Medium Access Control) protocol is a hot challenge. IEEE 802.11b/g/a/n networks are currently the most popular wireless LAN products on the market [1]. The conventional IEEE 802.11b and 802.11g/a specification provide up to 11 and 54 Mbps data rates, respectively. However, the MAC protocol that they are based upon is the same and employs a CSMA/CA (Carrier Sense Multiple Access/Collision Avoidance) protocol with binary exponential back-off. IEEE 802.11 DCF (Distributed Coordination Function) is the de facto MAC protocol for wireless LAN because of its simplicity and robustness [2,3]. Therefore, considerable research efforts have been put on the investigation of the DCF performance over wireless LAN [2]. With the successful deployment of IEEE 802.11a/b/g wireless LAN and the increasing demand for real-time applications over wireless, the IEEE 802.11n Working Group standardized a new MAC and PHY (Physical) layer specification to increase the bit rate to be up to 600 Mbps [3]. The throughput performance at the MAC layer can be improved by aggregating several frames before transmission [3]. Frame aggregation not only reduces the transmission time for preamble and frame headers, but also reduces the waiting time during CSMA/CA random backoff period for successive frame transmissions. The frame aggregation can be performed within different sub-layers. In 802.11n, frame aggregation can be performed either by A-MPDU (MAC Protocol Data Unit Aggregation) or A-MSDU (MAC Service Data Unit Aggregation). Although frame aggregation can increase the throughput at the MAC layer under ideal channel conditions, a larger aggregated frame will cause each station to wait longer before its next chance for channel access. Under errorprone channels, corrupting a large aggregated frame may waste a long period of channel time and lead to a lower MAC efficiency [4]. On the other hand, wireless LAN mobile stations that are defined as the stations that access the LAN while in motion are considered in this chapter. The previous paper analyzed the IEEE 802.11b/g/n MAC performance for wireless LAN with fixed stations, not for wireless LAN with mobile stations [5, 6, 7, 8, 9, 10]. On the contrary, Xi Yong [11] and Ha Cheol Lee [12] analyzed the MAC performance for IEEE 802.11 wireless LAN with mobile stations, but considered only IEEE 802.11 and 802.11g/a wireless LAN specification. So, this chapter summarizes all the reference papers and analyzes the IEEE 802.11b/g/a/n MAC performance for wireless LAN with fixed and mobile stations. In other words, we will present the analytical evaluation of saturation

The carrier-sensing multiple access with collision avoidance (CSMA/CA) protocol is the most well-known medium access control (MAC) protocol for wireless networks. Both the distributed coordination function (DCF) defined in IEEE 802.11 and the MAC layer defined in IEEE 802.15.4 are based on the CSMA/CA protocol. Nevertheless, these two standards have quite different carrier-sensing mechanisms. Different to continuous carrier sensing in DCF, an IEEE 802.15.4 node only senses the channel once just after a backoff. Sensing-once mechanism can reduce the computation loading on the CPU. However, it significantly increases the probability of failure transmission because a node is not fully aware of channel activity. This paper first proposes a software architecture integrating proper hardware features for designing a DCF-based MAC protocol and then successfully implements it on a low-power transceiver. In addition, this paper conducts experiments in a star topology network to compare the performance of the above DCF-MAC protocol with the IEEE 802.15.4 MAC protocol. Experimental results show that, without continuous sensing, the IEEE 802.15.4 network suffers a high transmission failure probability as the network size increases. Consequently, the proposed DCF-based MAC protocol outperforms the IEEE 802.15.4 MAC protocol in terms of packet loss probability and throughput.

In this paper, a power control strategy is proposed for a low voltage microgrid, where the mainly resistive line impedance, the unequal impedance among DG units and the microgrid load locations make the conventional frequency and voltage droop method unpractical. The proposed power control strategy contains a virtual inductor at the interfacing inverter output and an accurate power control and sharing algorithm with consideration of both impedance voltage drop effect and DG local load effect. Specifically, the virtual inductance can effectively prevent the coupling between the real and reactive power by introducing a mainly inductive impedance. On the other hand, based on the inductive impedance, the proposed accurate reactive power sharing algorithm functions by estimating the impedance voltage drops and significantly improves the reactive power control and sharing accuracy. Finally, considering the different locations of loads in a microgrid, the reactive power control accuracy is further improved by employing an on-line estimated reactive power offset to compensate DG local load effects. The proposed power control strategy has been tested experimentally on a low voltage microgrid prototype.

Prior works on power control strategy need to estimate all users' channel state information (CSI), which consumes both spectrum and time. Two efficient and low-complexity power control strategies, namely quality of experience (QoE) based power control scheme and distance based power control strategy, are proposed for an ambient backscatter based spectrum-sharing network. In the proposed power control schemes, there is no need to estimate all users' CSI. In the QoE-based power control strategy, only the <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${K}$ </tex-math></inline-formula> primary users with the highest priority feedback their CSI. We introduce an attenuation factor to reduce the transmit power to satisfy the interference threshold on primary users. Then, considering the short transmission distance of secondary backscatter communication and randomly distributed primary users, we propose the distance-based power control scheme, in which only the users within the backscatter distance need to feedback their CSI. Closed-form expressions for the outage probabilities of primary and secondary systems are derived over the Nakagami- <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${m}$ </tex-math></inline-formula> channels under the proposed two power control strategies. The system energy efficiency are also analyzed. Simulation results are conducted to verify the analytical results. Finally, outage performance and energy efficiency of the proposed schemes are compared with that of the existing nearest- <inline-formula xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink"> <tex-math notation="LaTeX">${K}$ </tex-math></inline-formula> users based power control strategy. It is shown that the proposed power control strategies have lower outage probabilities and higher energy efficiency.

Power efficient ultra-wideband based wireless communication for wireless body area network applications

Medium access control (MAC) protocols provide a means to nodes to access the wireless medium efficiently and collision free to the best of their ability. In this paper we provide a survey of MAC protocols developed for mobile ad hoc (MANETs) in the past based on certain methods and techniques such as multiple radios, multiple channels and specialized beamforming antennas. We discuss some of the MAC protocols designed for wireless sensor networks (WSNs) and their applicability in a MANET environment. There are some similarities between MANETs and WSN's in general but there is also critical differences between the two that affect the design of MAC protocols for both these networks. Traditionally, MAC protocols have been classified on the basis of two broad categories of contention free and contention based MAC protocols but a number of new algorithms proposed in the recent past merge the two schemes together in a single MAC solution and thus there is a need for a new classification approach. MANETs have their unique constraints and characteristics. In this classification, we will discuss various MAC solutions proposed in the past in the light of these constraints and characteristics. We do not intend to explain each and every protocol since the number of MAC solutions proposed in the past decade or so is very large. The purpose of this article is to give the readers a general idea on the various techniques and methods used in literature to develop MAC protocols for MANETs. The techniques range from algorithmic changes such as cross-layer design to enhancement in hardware such as directional antennas.

Dense wireless ad-hoc networks (DWAN) is developed with explosive growth of users and traffics, which means that the future network will bear more frequent and intensive communication services under the condition of limited spectrum resource. To meet the requirement of DWAN, an efficient medium access control (MAC) design has been a hot research topic. Towards the current MAC protocols, we mainly focus on addressing two issues in DWAN: (1) serious collisions; (2) low efficiency of spectrum utilization. In this paper, we propose a hybrid MAC with multi-slot reservation for DWAN, called MRPMAC, which is based upon the architecture of the carrier sense multiple access/collision avoidance and time division multiples access. In the proposed MRPMAC protocol, the network collisions are alleviated by using multi-slot reservation (MSR) scheme, and the frequency spectrum efficiency is improved through power control mechanism. Concretely, just with one handshake in the proposed MRPMAC protocol, multiple slots are reserved and multiple concurrent data transmissions are periodically initiated over single channel without collisions. Therefore, spectrum reusing can be achieved, the network throughput is greatly improved as well as quality of service can be ensured in DWAN. Furthermore, the upper bound of slot utilization in MRPMAC is analyzed. Through simulations using ns-2 simulator, we validate that the upper bound of throughput gain brought by power control scheme in MRPMAC is twice as high as pure MSR scheme, and demonstrate that system throughput of MRPMAC outperforms IEEE 802.11 DCF and POWMAC about 150 and $$67\%$$ , respectively.

In packet radio networks, especially an ad hoc wireless network using IEEE 802.11 as the MAC (media access control) protocol, power control is a crucial issue. By using a judicious power control mechanism, co-channel interference can be significantly reduced, thus improving the channel spatial reuse and network capacity. However, efficient power control in an IEEE 802.11 system is very challenging because according to the standard, fixed power is used for transmitting packets, and there is only one channel. In this paper, we propose an enhancement to the standard IEEE 802.11 MAC protocol by improving the handshaking mechanisms and adding one separate power control channel. With the control channel, the receiver notifies its neighbors its noise tolerance. Thus, the neighbors can adjust their transmission power levels to avoid packet collisions at the receiver. Through extensive simulations using NS-2, our proposed power control mechanism is found to be effective in that network throughput can be increased by about 10%, and the battery utilization can also be improved at the same time.

In this paper we study the correlations that exist between the required transmission power of RTS, CTS, DATA and ACK frames to guarantee a successful 4-way handshake in wireless ad hoc networks based on the IEEE 802.11 distributed coordination function (DCF). From these correlations, and starting from a set of different initial conditions, we can derive a class of power controlled media access control (MAC) algorithms for single channel ad hoc networks based on the existing IEEE 802.11 DCF. From substantial simulations of the different algorithms and comparison to some prominent alternatives, we come to a conclusion that contradicts the intuitively sound, commonly held belief which states that sending control frames at maximum power - to reduce interference on the long data frames - then, the ensuing long data frames at a lower, yet sufficient power level decreases power consumption per carried bit.

Variable rate power-controlled batch-based channel assignment for enhanced throughput in cognitive radio networks

Applying directional antennas in wireless ad hoc networks can theoretically achieve higher spatial multiplexing gain and, thus, higher network throughput. However, in practice, deafness, hidden-terminal, and exposed terminal problems are exaggerated with directional antennas, and they cause the degradation of the overall network performance. Although there are several random-access-based medium-access control (MAC) protocols being proposed in the literature for networks with directional antennas, the deafness, hidden-terminal, and exposed terminal problems have yet to be fully solved. In this paper, we present a new MAC protocol called the dual-sensing directional MAC (DSDMAC) protocol for wireless ad hoc networks with directional antennas. Different from existing protocols, the DSDMAC protocol relies on the dual-sensing strategy to identify deafness, resolve the hidden-terminal problem, and avoid unnecessary blocking. The integrity of the DSDMAC protocol is verified and validated using , which is a formal protocol verification and validation tool. We further develop an analytical framework to quantify the performance of the DSDMAC protocol and conduct extensive simulations, which verify the accuracy of the analysis. The protocol verification, analysis, and simulation results show the robustness and superior performance of the DSDMAC protocol, which can achieve a much higher network throughput and lower delay utilizing the spatial multiplexing gain of the directional antennas. The results presented in this paper show that the proposed DSDMAC protocol can substantially outperform the state-of-the-art protocols.

The current medium access control (MAC) protocol of the wireless access in vehicular environments (WAVE) system is based on IEEE 802.11 distributed coordination function (DCF) and enhanced distributed channel access (EDCA), which have drawbacks in supporting throughput-sensitive non-safety applications in vehicular ad-hoc network (VANET). In order to address the problem, we propose a novel MAC protocol, namely vehicular MESH network (VMESH), which is specifically designed for the control channel (CCH) and multiple service channels (SCHs) structure of WAVE. A synchronized and distributed beaconing scheme is employed in the VMESH protocol for the purposes of neighborhood awareness and dynamic resource reservation on SCHs. The advantages of the VMESH protocol in supporting the throughput-sensitive non-safety applications in VANET are shown through the theoretical analysis comparing to the current WAVE MAC.

In this paper we propose a simple relay enabled medium access (SRMAC) protocol that enables cooperative relay transmissions. Due to the wireless signal power attenuation with distance, using a relay in a wireless network can make wireless networking more bandwidth efficient at the expense of requiring multiple transmissions for a single packet. Standard MAC protocols such as the IEEE 802.11 MAC protocol, while useable with relaying, however are not designed explicitly for relay communication. When IEEE 802.11 MAC protocol is used for cooperative communication such a relaying, each packet transmission would need to separately contend for the channel via a channel access procedure which can use significant resources (both energy and bandwidth). Because using a single relay requires two transmissions, an efficient medium access control (MAC) protocol that supports two hop transmission is needed. We introduce a protocol, SRMAC, which is a simple cooperative MAC protocol that utilizes information from the physical layer for the MAC operation of relay networks. We consider the bandwidth efficiency of SRMAC protocol considering both the physical layer and MAC layer. The SRMAC protocol includes the possibility of both cooperative transmission and direct transmission. With SRMAC, cooperative transmission (relaying) can be dynamically chosen when it is more beneficial than direct transmission. The SRMAC protocol can improve the throughput by up to 20% compared to conventional MAC protocols.

Since cognitive wireless network (CRN) has the characteristic of secondary use, it can enable the device to dynamically access available spectrum without interference to primary users (PUs), which can effectively alleviate contradiction between the lack of spectrum resources and the growing demand for wireless access. However, Medium Access Control (MAC) protocol as CRN core components, can achieve competition access of the licensed spectrum and coordination control, which will maximize spectrum utilization efficiency and network throughput. The contribution of this survey is threefold. First, we analyze the characteristics of the existed multi- channel MAC protocol in CRN; Second, according to the different ways of spectrum access in CRNs, the multi-channel MAC protocols are classified into time-slotted based MAC protocol, control channel based MAC protocol and hybrid MAC protocol, and the paper emphatically analyzed the advantages and disadvantages of these multi-channel MAC protocols; Finally, the paper explores the difficulties and the challenges of multi-channel MAC protocols design in cognitive wireless network.

Cognitive Radio (CR) exploits underutilized licensed spectrums to improve its bandwidth availability. Using CR technology, a node is able to adapt its transmission and reception radio parameters including channel frequency dynamically according to local spectrum availability. For channel access between wireless nodes, a cognitive Medium Access Control (MAC) protocol is necessary to coordinate the CRs. Multi-channel MAC protocol extensions have been proposed in IEEE802.11 to enable a node to operate in multiple channels in order to improve network-wide throughput. These multi-channel MAC protocols have several functions that can be leveraged by cognitive MAC protocols due to their similarities in certain aspects, though the CR has an additional requirement to cope with the existence of licensed users that have higher authority over the channels. Current research in cognitive MAC protocols assumes the availability of a common control channel at all times, which is an approach in the multi-channel MAC protocols. This approach has certain hardware requirements that may not be readily available at CR nodes. Hence, other approached may be necessary. In this paper, various types of multi-channel MAC protocols are reviewed, followed by discussion of their merits and demerits in multi-channel environments. The purpose is to show the additional functionalities and challenges that each multi-channel MAC protocol has to offer and address in order to operate in multihop CR networks. By providing discussion on possible technology leverage from multi-channel to cognitive MAC protocols, we aim to establish a foundation for further research and discussion.