DL CSI acquisition and feedback in FDD massive MIMO via path aligning

Massive multiple-input multiple-output (massive-MIMO) is considered as the key technology to meet the huge demands of data rates in the future wireless communications networks. However, for massive-MIMO systems to realize their maximum potential gain, sufficiently accurate downlink (DL) channel state information (CSI) with low overhead to meet the short coherence time (CT) is required. Therefore, this article aims to overcome the technical challenge of DL CSI estimation in a frequency-division-duplex (FDD) massive-MIMO with short CT considering five different physical correlation models. To this end, the statistical structure of the massive-MIMO channel, which is captured by the physical correlation is exploited to find sufficiently accurate DL CSI estimation. Specifically, to reduce the DL CSI estimation overhead, the training sequence is designed based on the eigenvectors of the transmit correlation matrix. To this end, the achievable sum rate (ASR) maximization and the mean square error (MSE) of CSI estimation with short CT are investigated using the proposed training sequence design. Furthermore, this article examines the effect of channel hardening in an FDD massive-MIMO system. The results demonstrate that in high correlation scenarios, a large loss in channel hardening is obtained. The results reveal that increasing the correlation level reduces the MSE but does not increase the ASR. However, exploiting the spatial correction structure is still very essential for the FDD massive-MIMO systems under limited CT. This finding holds for all the physical correlation models considered.

In frequency-division duplexing (FDD) massive multiple-input multiple-output (MIMO) systems, 1-bit compressed sensing (CS)-based superimposed channel state information (CSI) feedback has shown many advantages, while still faces many challenges, such as low accuracy of the downlink CSI recovery and large processing delays. To overcome these drawbacks, this paper proposes a deep learning (DL) scheme to improve the 1-bit compressed sensing-based superimposed CSI feedback. On the user side, the downlink CSI is compressed with the 1-bit CS technique, superimposed on the uplink user data sequences (UL-US), and then sent back to the base station (BS). At the BS, based on the model-driven approach and assisted by the superimposition-interference cancellation technology, a multi-task detection network is first constructed for detecting both the UL-US and downlink CSI. In particular, this detection network is jointly trained to detect the UL-US and downlink CSI simultaneously, capturing a globally optimized network parameter. Then, with the recovered bits for the downlink CSI, a lightweight reconstruction scheme, which consists of an initial feature extraction of the downlink CSI with the simplified traditional method and a single hidden layer network, is utilized to reconstruct the downlink CSI with low processing delay. Compared with the 1-bit CS-based superimposed CSI feedback scheme, the proposed scheme improves the recovery accuracy of the UL-US and downlink CSI with lower processing delay and possesses robustness against parameter variations.

To enhance the performance of a massive multiple-input multiple-output (MIMO) system, the downlink channel state information (CSI) should be compressed and fed back to the base station (BS) effectively in a frequency division duplex (FDD) mode. In contrast to traditional compression methods that rely on the particular prior assumptions, deep learning (DL) based CSI feedback has the potential to learn informatively from the hidden complex models behind the data. However, most of the current DL based methods stay in the early stage that uses DL modules directly from image processing, while the distinctive channel semantic information has been largely ignored. In this letter, considering the spatial-temporal correlation property of CSI matrices, we propose an architecture based on criss-cross attention, called CCA-Net, which extracts the channel features more precisely by leveraging the contextual information along the delay and angle domain. Meanwhile, a real and imaginary part combination module is used to assist in extracting the internal features of CSI. In addition, to reap the computational resources at BSs, a scalable decoder is designed to extend the reconstruction abilities. Experiments demonstrate that our network achieves better normalized mean square error with lower flops than existing state-of-the-art algorithms.

In the multiuser multiple-input multiple-output (MU-MIMO) system, to reduce the influence of channel correlation on system performance, the base station (BS) should select the appropriate subset of user equipments (UEs) according to their channel state information (CSI). Due to a lack of channel reciprocity, the downlink CSI needs to be fed back to the BS in frequency division duplexing (FDD) mode. Some scholars have exploited kinds of deep neural networks (DNNs) for sensing and recovering CSI. However, user selection after all the CSI is reconstructed by DNNs will bring a great time delay. In this paper, we propose a deep learning-based CSI feedback scheme called US-CsiNet. Based on adversarial autoencoder (AAE), US-CsiNet can explicitly cover user schedule information while representing CSI. At the UE side, the encoder of US-CsiNet maps the CSI into codewords of which part are feature information for user schedule. Then the BS applies these partial codewords to separate the UEs into different groups and select active UEs. Finally, the decoder of AAE reconstructs the CSI of these active UEs. US-CsiNet can not only simplify the user selection process but also guarantee the accuracy of CSI reconstruction. The simulation results show that the proposed approach outperforms maximum channel gain (MCG) user selection algorithms and achieves the nearly same performance with semiorthogonal user selection (SUS) which needs full CSI of all users at the BS.

Accurate downlink channel state information (CSI) is required to be fed back to the base station (BS) in frequency division duplexing (FDD) massive multiple-input multiple-output (MIMO) systems in order to achieve maximum antenna diversity and multiplexing. However, downlink CSI feedback overhead scales with the number of transceiver antennas, a major hurdle for practical deployment of FDD massive MIMO systems. To solve this problem, we propose a compressive sampled CSI feedback method based on deep learning (SampleDL). In SampleDL, the massive MIMO channel matrix is sampled uniformly in time/frequency dimension before being fed into neural networks (NNs), which will reduce the computational resource/time at user equipment (UE) as well as enhance the CSI recovery accuracy at the BS. Both theoretical analysis and normalized mean square errors (NMSE) results confirm the advantages of the proposed method in terms of time complexity and recovery accuracy. Besides, a suitable CSI feedback period is explored by link level simulations, which aims to further reduce the overhead of CSI feedback without degrading the communication quality.

In a massive multiple-input multiple-output (MIMO) system, channel state information (CSI) is essential for the base station (BS) to achieve high performance gain. The user equipment (UE) needs to estimate CSI and then feeds it back to the BS in the frequency division duplexing (FDD) mode. Effective compression of CSI will significantly reduce the cost of channel feedback, and many deep learning (DL) based channel compression schemes have been proposed to achieve this goal. In this paper, rather than viewing CSI as images as in most existing works, we propose a new perspective of viewing CSI as an information sequence and analogize CSI feedback to a machine translation task. Further, we propose a novel sequence to sequence (Seq2Seq) model for CSI feedback composed of only recurrent neural networks and a small-scale fully connected layer, avoiding the convolution and pooling structure commonly used in current DL-based works. The advantage of this scheme is that it fully integrates the physical characteristics of the MIMO channel in the spatial domain into the structure of the neural network and avoids the loss of some prominent unsmooth or discontinuous features caused by the inappropriate convolution and pooling operation. Simulation results show that the proposed Seq2Seq model outperforms other DL-based CSI compression techniques under various communication scenarios.

Chapter 7 - Channel feedback for mmWave massive MIMO

Deep learning (DL)-based channel state information (CSI) feedback improves the capacity and energy efficiency of massive multiple-input multiple-output (MIMO) systems in frequency division duplexing mode. However, multiple neural networks with different lengths of feedback overhead are required by time-varying bandwidth resources. The storage space required at the user equipment (UE) and the base station (BS) for these models increases linearly with the number of models. In this paper, we propose a DL-based changeable-rate framework with novel quantization scheme to improve the efficiency and feasibility of CSI feedback systems. This framework can reutilize all the network layers to achieve overhead-changeable CSI feedback to optimize the storage efficiency at the UE and the BS sides. Designed quantizer in this framework can avoid the normalization and gradient problems faced by traditional quantization schemes. Specifically, we propose two DL-based changeable-rate CSI feedback networks CH- CsiNetPro and CH- DualNetSph by introducing a feedback overhead control unit. Then, a pluggable quantization block (PQB) is developed to further improve the encoding efficiency of CSI feedback in an end-to-end way. Compared with existing CSI feedback methods, the proposed framework saves the storage space by about 50% with changeable-rate scheme and improves the encoding efficiency with the quantization module.

In modern wireless systems, the feedback of DownLink (DL) Channel State Information (CSI) from User Equipment (UE) to Base Stations (BS) may require substantial computational and feedback bandwidth overheads. A promising approach to improve feedback efficiency is to leverage side information which is correlated to DL CSI. Despite potential of doing so, critical aspects remain underexplored in current research, particularly the quantification of the benefits and the inherent limitations of utilizing side information. This paper addresses these gaps by introducing a novel algorithm to compute the rate-distortion function for general compression scenarios incorporating side information. We apply this algorithm to the DL CSI feedback problem having UL CSI as the side information and generate rate-distortion functions. Using the estimated rate-distortion functions, we measure the gain of side information over diverse feedback rates and UE mobility profiles. The results reveal that the benefits of leveraging side information are particularly significant for UEs characterized by high mobility and constrained to operate at low feedback overheads.

In wireless communications, massive multiple-input multiple-output (MIMO) systems in which the base station (BS) is equipped with a large number of antennas can provide significant spectral and energy efficiency by means of simple signal processing. Therefore, massive MIMO is an attractive technology for next generation wireless communication systems and for green communications. There are two operation modes: time-division duplex (TDD) and frequency-division duplex (FDD) for massive MIMO systems, and the debate on the two modes is still discussed in the literature. The originator of massive MIMO systems, Marzetta, has presented the basic frame structures for both the TDD and the FDD modes. However, the basic frame structures do not carefully take the hardware impairments such as phase noise (PN) into account. In this paper, by taking the PN as the key hardware impairment into account, we recommend new and efficient frame structures for both the TDD and the FDD modes. The corresponding performance comparison between the two modes is also provided by using the data transmission efficiency (DTE) as the performance measurement. The comparison may help determine which mode should be used for massive MIMO systems.

Cell-free system where a group of base stations (BSs) cooperatively serves users has received much attention as a promising technology for the future wireless systems. In order to maximize the cooperation gain in the cell-free systems, acquisition of downlink channel state information (CSI) at the BSs is crucial. While this task is relatively easy for the time division duplexing (TDD) systems due to the channel reciprocity, it is not easy for the frequency division duplexing (FDD) systems due to the CSI feedback overhead. This issue is even more pronounced in the cell-free systems since the user needs to feed back the CSIs of multiple BSs. In this paper, we propose a novel feedback reduction technique for the FDD-based cell-free systems. Key feature of the proposed technique is to choose a few dominating paths and then feed back the path gain information (PGI) of the chosen paths. By exploiting the property that the angles of departure (AoDs) are quite similar in the uplink and downlink channels (this property is referred to as angle reciprocity), the BSs obtain the AoDs directly from the uplink pilot signal. From the extensive simulations, we observe that the proposed technique can achieve more than 60% reduction in feedback overhead over the conventional CSI feedback scheme.

Massive multiple-input multiple-output (MIMO) is believed to deliver unrepresented spectral efficiency gains for 5G and beyond. However, a practical challenge arises during its commercial deployment, which is known as the “curse of mobility”. The performance of massive MIMO drops alarmingly when the velocity level of user increases. In this paper, we tackle the problem in frequency division duplex (FDD) massive MIMO with a novel Channel State Information (CSI) acquisition framework. A joint angle-delay-Doppler (JADD) wideband precoder is proposed for channel training. Our idea consists in the exploitation of the partial channel reciprocity of FDD and the angle-delay-Doppler channel structure. More precisely, the base station (BS) estimates the angle-delay-Doppler information of the UL channel based on UL pilots using Matrix Pencil (MP) method. It then computes the wideband JADD precoders according to the extracted parameters. Afterwards, the user estimates and feeds back some scalar coefficients for the BS to reconstruct the predicted DL channel. Asymptotic analysis shows that the CSI prediction error converges to zero when the number of BS antennas and the bandwidth increases. Numerical results with industrial channel model demonstrate that our framework can well adapt to high speed (350 km/h), large CSI delay (10 ms) and channel sample noise.

Massive multiple-input multiple-output systems deploying a large number of antennas at the base station considerably increase the spectrum efficiency by serving multiple users simultaneously without causing severe interference. However, the advantage relies on the availability of the downlink channel state information (CSI) of multiple users, which is still a challenge in frequency-division-duplex transmission systems. This paper aims to solve this problem by developing a full transceiver framework that includes downlink channel training (or estimation), CSI feedback, and channel reconstruction schemes. Our framework provides accurate reconstruction results for multiple users with small amounts of training and feedback overhead. Specifically, we first develop an enhanced Newtonized orthogonal matching pursuit (eNOMP) algorithm to extract the frequency-independent parameters (i.e., downtilts, azimuths, and delays) from the uplink. Then, by leveraging the information from these frequency-independent parameters, we develop an efficient downlink training scheme to estimate the downlink channel gains for multiple users. This training scheme offers an acceptable estimation error rate of the gains with a limited pilot amount. Numerical results verify the precision of the eNOMP algorithm and demonstrate that the sum-rate performance of the system using the reconstructed downlink channel can approach that of the system using perfect CSI.

The work of cooperative perception realized by mmWave Vehicle to everything (V2X) [3] has pointed out that vehicles require much network bandwidth to exchange sensor information for safe automated driving; e.g., they require higher than 1Gbps V2V bandwidth to ensure safe velocity of 70 km/h. On the other hand, some research works have shown that channel state information (CSI) feedback is able to mitigate interference for 5G frequency division duplexing (FDD) mmWave massive MIMO systems. Existing approaches either do not consider the characteristics of FDD mmWave V2X systems or assume all channels are ideal, i.e., uncorrelated and identical. To achieve higher throughput and low overhead for FDD mmWave V2X systems, there are two major issues: (1) how to acquire an accurate CSI under the environment of non-identical channels, and (2) how to effectively use such information to improve overall system throughput. Our idea is to jointly consider the characteristics of the angle of arrival (AoA) method and Khler manifolds to design of codebook feedback approach for mmWave V2X massive systems. That is, to get an accurate CSI, we leverage the measurement method with the idea of the AoA approach. With this AoA measurement, we propose a novel Khler manifolds codebook feedback approach and determine an optimal bit allotment over each mmWave V2X link for achieving better interference reduction as well as lower overhead for V2X CSI exchange. In addition, our analytic results validate that proposed AoA Khler manifolds codebook feedback scheme is more adequate than the traditional CSI feedback with regard to interference reduction. Simulations show that the proposed AoA Khler manifolds codebook feedback scheme can significantly improve the vehicle rate and reduce the overhead for V2V CSI exchange.

Closed-loop MIMO system can provide dramatic gains in channel capacity. However, mobile terminal (MT) must feedback the downlink channel state information (CSI) to Base station (BS), and transmitting CSI is a heavy burden consuming considerable uplink bandwidth. To address this bottleneck problem, a zero-overhead downlink CSI feedback scheme is proposed in this paper. After receiving the downlink pilots, MT directly superposes the uplink pilot on the received analog downlink pilot, forms the hybrid pilot (HP), and then transmits HP to BS via uplink pilot channel. Because downlink CSI can be recovered from HP at BS, and HP is fed back to BS via the uplink pilot channel, no extra uplink channel is occupied and the overhead for CSI feedback is zero. Moreover, since no CSI estimation process is performed at MT, the terminal's complexity can be reduced. Numerical Simulations verify that, the proposed downlink CSI feedback has the higher precision than the traditional feedback schemes, and the MSE of CSI feedback can be reduced significantly.