Dual Notched Band Quad-Element MIMO Antenna With Multitone Interference Suppression for IR-UWB Wireless Applications

1.1 Impulse Radio (IR) Ultra Wideband (UWB) Communications Ultra wideband (UWB) communication is a fast emerging technology that offers new opportunities such as high data rates, low equipment cost, low power, precise positioning capability and extremely low interference Ghawami (2005). A wide range of possible UWB communication system applications includes radars due to UWB ultra high precision ranging at the centimeter level, wireless personal area networks (WPAN), sensor networks, imaging systems, UWB positioning systems, etc. Yang (2004), Kshetrimayum (2009). From a commercial point of view, the high data rates are the most attractive feature of UWB systems for which speeds of over 100Mb/s have been demonstrated Ghawami (2005). There exist three main types of UWB technologies: impulse radio (IR UWB), direct sequence (DS UWB), and multi-band orthogonal frequency division multiplexing (MB OFDM) Ran (2009). IR UWB communication technique is essentially different from all other communication techniques because it is carrier free and uses for communication between transmitters and receivers very narrow radio frequency (RF) pulses generated from the UWB pulse generator, while traditional transmission systems transmit information by varying the power, frequency, and/or phase of a sinusoidal wave in a modulation process Kshetrimayum (2009), Yao (2007). Consequently, complicated frequency mixers and local oscillators for carrier frequency up and down conversion are not necessary Yao (2007). IR UWB modulation techniques are especially important because the UWB spectrum has been made available by the Federal Communication Commission (FCC) and it can be used with IRs developed to date Lin (2005). Waveforms for IR UWB are designed to obtain a flat frequency response over the bandwidth of the pulse and to avoid a DC component. The large spectrum of a UWB signal may interfere with existing users. In order to keep this interference to the minimum, FCC specifies spectral masks for different applications, i.e. the allowed power output for specific frequencies Ghawami (2005). A contiguous bandwidth of 7.5GHz is available in the frequency interval of (3.1− 10.6)GHz at a maximum power output of −41.3dBm/MHz which is considered as extremely low Ghawami (2005). The power spectral density (PSD) of UWB systems defined as a ratio of the transmitted power P in watts and a signal bandwidth B in hertz is extremely low as compared to other communication systems due to the very wide bandwidth B of short pulses that are typically of nanosecond or picosecond order Ghawami (2005). The selection of the impulse signal type for IR UWB communication system is essential since it determines

In-car wireless data communications systems require a short-range unlicensed radio communications technology that causes a very low level of interference in the other, already deployed radio links and networks, offers low and medium data rate, can reuse the already occupied radio-frequency (RF) bands, and assures low probability of message collisions. Ultrawide band (UWB) impulse radio employs RF pulses with very short duration to carry the information; consequently, it is an optimal candidate for the in-car wireless communications and intravehicular wireless sensor networks. Data rate and shape of RF carrier pulse determine the performance of a UWB radio link. To limit the interference caused, the maximum power radiated by an UWB device is restricted by the Federal Communications Commission (FCC) in the U.S. Introducing a new mathematical model and starting from the FCC regulations, analytical expressions for the calculation of FCC power limits are derived here. It is shown that the low- and high-rate UWB impulse radio systems are peak and average power limited, respectively. The relationship between the mathematical model and the parameters of an UWB carrier pulse used in a built UWB radio is established. The performances of RF carrier pulses known from the literature are evaluated and compared. All expressions derived are verified by measurements.

Power efficient ultra-wideband based wireless communication for wireless body area network applications

Ultra wideband-impulse radio (UWB-IR) systems transmit data by ultra short pulses. The UWB-IR systems can achieve a time diversity gain by transmitting some pulses for each information symbol. In L. Yang et al. (2002) the space time (ST)-UWB-IR system was proposed to achieve a space-time diversity gain by transmitting space-time block coded symbols with some antennas. In the ST-UWB-IR system, the transmit antennas transmit the same symbol over an ST code block simultaneously. If all the transmit antennas can transmit different symbols independently, that is, if it separates the symbols from each antenna, we can expect a higher transmission rate than the ST-UWB-IR system. Moreover, at the same transmission rate, we can expect a larger diversity gain by sending more pulses for each symbol. This paper proposes a space hopping (SH)-UWB-IR system. In the SH-UWB-IR system, to allow each user to transmit different symbols from different antennas, a unique time hopping sequence is assigned to each antenna, which is known to the receiver. In addition, to get the larger diversity gain in the SH-UWB-IR system, the transmitted symbols are interleaved over the transmit antennas. From the results of our computer simulation, we show that when the number of users is small, the bit error rate (BER) of the SH-UWB-IR system is superior to that of the ST-UWB-IR system at the same data rate.

In free space optical (FSO) communication systems, atmospheric turbulence is the major cause of bit error rate (BER) performance degradation. The error performance of the system can be significantly improved with the help of spatial diversity by employing multiple transmit or receive apertures. However, correlation of channels under turbulence in the case of small separation between transmit apertures can substantially reduce the benefits of spatial diversity. Still, a thorough analysis of the system performance in terms of diversity order and coding gain for the FSO multiple-input single-output (MISO) system under turbulence influenced correlated channels has not been studied when the repetition coding is used to achieve improved BER performance. In this paper, we provide unique results of the BER performance analysis of the considered correlated FSO-MISO system over Gamma–Gamma distributed turbulence channel. Using the joint moment generating function of received signal-to-noise ratio (SNR), a novel generalized approximate BER expression is derived, followed by convergence test of the power series based BER expression using the Cauchy's ratio test. Then, an asymptotic analysis at high SNR is performed to obtain a novel closed-form expression for BER of FSO-MISO system. We also derive expressions for coding gain, diversity gain, and coding gain loss due to correlation in channels. Although the effect of correlation in channels on the BER performance of the system is analyzed under different scenarios, while it is observed that it does not affect the diversity order; it significantly degrades the coding gain of the considered system.

This paper proposes a novel method of using chaotic binary sequence in pulse amplitude modulation based ultrawideband (UWB) system to suppress interference and hence to improve the Bit Error Rate (BER) performance in the presence of narrowband interference (NBI). It is one of the very important considerations in the UWB systems as the spectrum of UWB overlays with the existing narrowband wireless systems. In the proposed method, the chaotic binary sequence is used across the frames within one symbol duration. The performance of the proposed scheme is analyzed using the channel models proposed by IEEE 802.15.3a working group for short range, high data rate wireless communications. The simulation results show that the proposed system has better BER performance compared to the existing systems, in the presence of NBI. In addition to the suppression of NBI, the proposed scheme has an added level of security due to the chaotic spreading.

In an ultra-wideband (UWB) impulse radio (IR) system, a number of pulses, each transmitted in an interval called a "frame," is employed to represent one information symbol. Conventionally, a single type of UWB pulse is used in all frames of all users. In this paper, IR systems with multiple types of UWB pulses are considered, where different types of pulses can be used in different frames by different users. Both stored-reference (SR) and transmitted-reference (TR) systems are considered. First, the spectral properties of a multipulse IR system with polarity randomization is investigated. It is shown that the average power spectral density is the average of the spectral contents of different pulse shapes. Then, approximate closed-form expressions for the bit-error probability of a multipulse SR-IR system are derived for Rake receivers in asynchronous multiuser environments. The effects of both interframe interference (IFI) and multiple-access interference (MAI) are analyzed. The theoretical and simulation results indicate that SR-IR systems that are more robust against IFI and MAI than a "conventional" SR-IR system can be designed with multiple types of ultra-wideband pulses. Finally, extensions to multipulse TR-IR systems are briefly described.

We investigate timing tolerances of ultra-wideband (UWB) impulse radios. We quantify the bit-error rate (BER) sensitivity to epoch timing offset under different operating conditions, including frequency-flat fading channels, dense multipath fading channels, multiple access with time hopping, and various receiver types including sliding correlators and RAKE combiners. For a general correlation-based detector, we derived in Part I unifying expressions for the decision statistics as well as BER formulas under mistiming, given fixed channel realizations. In Part II, we provide a systematic approach to BER analysis under mistiming for fading channels. The BER is expressed in terms of the receiver's energy capture capability, which we quantify under various radio operating conditions. We also develop the optimal demodulator in the presence of timing offset and show a proper design of the correlation-template that is robust to mistiming. Through analyses and simulations, we illustrate that the reception quality of a UWB impulse radio is highly sensitive to both timing acquisition and tracking errors. © 2005 IEEE.

In this paper, we propose a framework for the study of power consumption and bit error rate (BER) performance of non-coherent impulse radio ultra wideband (IR-UWB) correlation receivers in the IEEE 802.15.3a channel. Using this framework, transmitted reference (TR) and energy detection (ED) correlation receivers are studied and compared. The receivers are assumed to operate in the 3.1-5GHz band targeting low-power consumption, where the correlation is performed in the analog domain. The BER performance is based on the channel averaged signal-to-noise ratio (SNR). Moreover, the framework addresses and compares different power consumption and performance parameters, namely the signal bandwidth, integration window, number of pulses per bit, and analog delay-lines. Then, we use the proposed framework for studying the fundamental design components of a wireless wearable human locomotion tracking and health-monitoring system based on UWB sensors. Ultimately, this system should provide high accuracy while consuming ultralow power. The study includes the link and power budgets of the system under investigation in addition to simulation results for the knee velocity. The accuracy provided by this system outperforms the accuracy of the current commercially available systems while preserving ultra-low power consumption.

The bit error rate (BER) performance of time hopping pulse position modulation (TH-PPM) impulse radio employing spiral antennas is investigated. Two-arm equiangular and Archimedean spirals are considered. Analytical compensation technique is applied to reduce antennas dispersion and enhance the system's BER performance.

We propose a direct-sequence pulse-amplitude modulation (DS-PAM) ultra-wideband (UWB) system which employs a non-linear chirp waveform instead of the conventional Gaussian monocycle in this paper.In the approved frequency for UWB, there exist myriad narrowband interferers.Specifically, we focus on the mutual interference between UWB systems and 802.11aWLAN.This paper offers a method to suppress this inband narrowband interference by introducing a kind of non-linear chirp waveform.Using the proposed non-linear chirp waveform, the effects of one or more narrowband interference sources with different frequencies can be suppressed.System performance of UWB systems in the narrowband interference environment can be improved.Computer simulations with additive white Gaussian noise successfully demonstrate an increase in performance with the proposed system as compared to traditional linear chirp systems.

Ultra wide band (UWB) is an extremely promising wireless technology for researchers and industrials. One of the most interesting is its high data rate and fading robustness due to selective frequency fading. However, beside such advantages, UWB system performance is highly affected by existing narrowband interference (NBI), undesired UWB signals and tone/multi-tone noises. For this reason, research about NBI cancellation is still a challenge to improve the system performance vs. receiver complexity, power consumption, linearity, etc. In this work, the two major receiver sections, i.e., analog (radiofrequency or RF) and digital (digital signal processing or DSP), were considered and new techniques proposed to reduce circuit complexity and power consumption, while improving signal parameters. In the RF section, different multiband UWB low-noise amplifier key design parameters were investigated like circuit configuration, input matching and desired/undesired frequency band filtering, highlighting the most suitable filtering package for efficient UWB NBI cancellation. In the DSP section, due to pulse transmitter signals, different issues like modulation type and level, pulse variety, shape and color noise/tone noise assumptions, were addressed for efficient NBI cancelation. A comparison was performed in terms of bit-error rate, signal-to-interference ratio, signal-to-noise ratio, and channel capacity to highlight the most suitable parameters for efficient DSP design. The optimum number of filters that allows the filter bandwidth to be reduced by following the required low sampling rate and thus improving the system bit error rate was also investigated.

This paper presents a bit error rate (BER) performance analysis of vehicular communication systems (VCS) based on the IEEE 802.11p standard assuming velocity variations of the mobile stations (MSs). To that end, we propose a novel Monte Carlo vehicle-to-vehicle (V2V) fading channel simulator that takes into account the accelerated motion and trajectory variations of the MSs. On the grounds of the proposed channel simulator, we assess the impact of the MSs' velocity variations on the system's BER performance. We assume that the channel state information is obtained following the least-squares (LS) channel estimation techniques that are commonly implemented in commercial off-the-shelf WiFi devices. The results show that the velocity variations have in general a slight impact on the system's BER performance. However, the performance is aggravated as the data frame length or the relative speed increases. The simulation framework presented in this paper can be used as a benchmark to evaluate the performance of the emerging VCS in safety critical scenarios.

Pulse-based communication systems are a promising candidate in the deployment of future wireless networks, thanks to the potential robustness and capacity guaranteed by the transmission of pulses of very short duration. In the framework of pulse-based communication systems, the Impulse Radio-Ultra Wide Band (IR-UWB) technique recently received particular attention. In the past, most of the UWB research focused on hardware and physical layer aspects in order to solve the technological challenges posed by IR-UWB. UWB peculiar characteristics may, however, also stimulate innovative higher layers' design. This work addresses Medium Access Control (MAC) issues for IR-UWB communication systems and extends the discussion to wireless optical communication systems. Typical characteristics of an IR-UWB system are presented, and solutions proposed for such systems at the MAC layer are reviewed. The applicability of such solutions to an optical wireless communications system is then discussed, highlighting analogies and differences between IR-UWB and wireless optical systems.

Multi-carrier code division multiple access (MC-CDMA)has been considered as a strong candidate for next generation wireless communication system due to its excellent performance in multi-path fading channel and simple receiver structure. However, like all the multi-carrier transmission technologies such as OFDM, the inter-carrier interference (ICI) produced by the frequency offset between the transmitter and receiver local oscillators or by Doppler shift due to high mobility causes significant BER (bit error rate) performance degradation in MC-CDMA system. Many ICI cancellation methods such as windowing and frequency domain coding have been proposed in the literature to cancel ICI and improve the BER performance for multi-carrier transmission technologies. However, existing ICI cancellation methods do not cancel ICI entirely and the BER performance after ICI cancellation is still much worse than the BER performance of original system without ICI. Moreover, popular ICI cancellation methods like ICI self-cancellation reduce ICI at the price of lowering the transmission rate and reducing the bandwidth efficiency. Other frequency-domain coding methods do not reduce the data rate, but produce less reduction in ICI as well. In this paper, we propose a novel ICI cancellation scheme that can eliminate the ICI entirely and offer a MC-CDMA mobile system with the same BER performance of a MC-CDMA system without ICI. More importantly, the proposed ICI cancellation scheme (namely Total ICI Cancellation) does not lower the transmission rate or reduce the bandwidth efficiency. Specifically, by exploiting frequency offset quantization, the proposed scheme takes advantage of the orthogonality of the ICI matrix and offers perfect ICI cancellation and significant BER improvement at linearly growing cost. Simulation results in AWGN channel and multi-path fading channel confirm the excellent performance of the proposed Total ICI Cancellation scheme in the presence of frequency offset or time variations in the channel, outperforming existing ICI cancellation methods.