Dynamics Characteristics of an Indirect District Heating System and Operational Optimization

In the transmission process of gear system, the change of load will make the system in different states of motion, which affects the transmission efficiency of gear system. It is important to investigate the nonlinear dynamic characteristics of gear system under different load states. Using straight cylindrical gears as the object of study, the concentrated mass method is used to establish a dynamic model that takes into account nonlinear factors such as tooth side clearance, time-varying meshing stiffness and transmission errors. The differential equations of the system are solved by the Longe-Kutta method to obtain the bifurcation diagram, the maximum Lyapunov exponent diagram and the phase plane diagram of the gear system to analyze the effect of the meshing damping ratio on the dynamic characteristics of the system under different load states. The results show that the influence of the engagement damping ratio on the dynamic characteristics of the system is greater under light load conditions, showing different states of motion as the engagement damping ratio gradually increases. Under heavy load conditions, the effect of the engagement damping ratio on the dynamic characteristics of the system is small. Appropriately increasing the mesh damping ratio is beneficial to the gear system to avoid the chaotic zone and maintain a stable cyclic motion state. The results of the study provide a reference for the design of gear systems with variable loads.

Experimental study on thermal dynamic characteristics of gear transmission system

Studies on the planetary gear have attracted considerable attention because of its advantages, such as compactness, large torque-to-weight ratio, vibrations, and high efficiency, which have resulted in its wide applications in industry, wind turbine, national defense, and aerospace fields. We have established a novel dynamic model of the planetary gear transmission by using Newton’s theory, in which some key factors such as time-variant meshing stiffness, phase relationships, and tooth contact characteristics are considered. The influences of gear axial tipping, operating conditions, and the meshing phase on the contact characteristics and the dynamic characteristics were researched systematically. It was found that the contact area of the tooth surface was moved due to the axial gear tipping, which obviously affected the meshing stiffness. With the increase in the inclination angle of the sun gear, the meshing stiffness decreases, which produces an evident influence on the high natural frequency in the planetary transmission system. In terms of the dynamic characteristics of the system, the component of rotating frequency appeared in the dynamic meshing force of the sun gear and the planetary gear. Moreover, the floating track of the center wheel varied significantly and exhibited an oval distribution as the inclination angle of the sun gear changed. When the inclination angle of the sun gear increased, the rotating frequency component increased significantly, but the other meshing frequency components remained unchanged; meanwhile, the deformation of the floating track also increased. If the inclination angle of the sun gear changes, the vibration state of the system and the collision impact could become more serious, and the lifetime of the planetary transmission system will reduce. Furthermore, when the load was increased, we found that the gear-tooth contact zone transformed from line contact to surface contact, the meshing stiffness increased, the effect of high natural frequency on the planetary transmission system became more evident, but its low-order natural frequency remained stable. With regard to the dynamic characteristics of the system, the components of the major frequency at the external gearing remained unchanged, but the rotation frequency of the sun gear and the meshing frequency amplitude increased linearly with the increase in load. In conclusion, the variation in the meshing stiffness of the planetary gear system had minor impact on the low-order natural frequency, but had a significant impact on the high natural frequency of the planetary transmission system due to the phase variation of the gear.

Digital control of a continuoiis-time system implies discretization in time of the system. The discretization is likely to bring about changes in the dynamic characteristics of the continuous-time system. Two approaches to the design of a digital control system can be considered: 1) discretization of a previously designed continuoustime control system and 2) direct design in the discrete-time domain. The difference between these two approaches and their effects on a closed-loop control system employing a Luenberger-type observer is demonstrated. The first approach consists of simulating a continuous-tim e control system on a digital computer. Because the possibility exists that a given set of parameters of the continuous-time system, such as gains and observer poles, will produce a change in the dynamic characteristics of the system during digital simulation, the question is how large the sampling time can be without affecting adversely the discrete simulation. An example of an unstable digital simulation of a closed-loop control system employing a deterministic observer that is stable in continuous-ti me is presented. The second approach inherently guards against changes in the dynamic characteristics that may be caused by discretization. The two approaches are compared by using a second-order dynamic system.

STRUCTURAL IDENTIFICATION FROM AMBIENT VIBRATION MEASUREMENT USING THE MULTIVARIATE AR MODEL

The coupled heave and pitch motions of a ship sailing in head waves affect the stability of the marine rotor-bearing system. Based on the theory of analytical mechanics, this study establishes a dynamic model of the rotor-bearing system subjected to the coupled motions of heave and pitch, considering nonlinear oil film moments produced by the tilting of the rotor in the bearings. The nonlinear dynamic behaviours of the system are analysed using numerical methods to obtain Poincaré sections, bifurcation diagrams, and the largest Lyapunov exponents. The results show that dynamic bifurcation characteristics reveal complex quasi-periodic motion of upper and lower branches after the initial instability of the system, and the speed of second instability increase markedly. At high speeds, the amplitude of the rotor system increases sharply, which can cause the rotor to touch the inner wall of the bearings in the quasi-periodic state and a failure to transition to the chaotic state. Additionally, the effects of heave and pitch amplitude variations on the dynamic characteristics of the system are also discussed.

The slender type tool usually can be used in milling the thin-walled components in a narrow and deep processing space, and the tool and the workpiece are usually deemed a system because the stiffness of both is closed. The milling stability is influenced by both the coupling deflection and dynamic characteristics of the tool-workpiece system. In order to investigate the time variation of the coupling deflection and dynamic characteristics of the tool-workpiece system, a new computational model was established in this paper. The workpiece was divided into several milling units, and the whole milling process was divided into a series of corresponding sub-milling processes. The coupling deflection of the tool-workpiece system in the sub-milling process was induced by milling force, and the milling force in the next sub-milling process was reversely induced by the coupling deflection of the tool-workpiece system, and by this analogy. Therefore, the thicknesses of units were different under the interaction between the milling forces and the coupling deflections. The changes of dynamic characteristics of the tool-workpiece system were induced by the changes of thicknesses of units. Based on the influences of the coupling deflection and the dynamic characteristics of the tool-workpiece system, a new stability lobe diagram which can show different stability zones and chatter zones in different process positions was obtained. Experimental testing has been conducted to validate the newly established model.

The study on the position-dependent dynamic characteristics of a vertical ball screw feed system without counterweight is an important step in the enhancement of the structural performance of mini-type vertical milling machines. The ball screw is generally driven by a servomotor, which converts a rotary motion into a linear motion through a screw–nut pair. To assess the position-dependent dynamic characteristics of a vertical ball screw feed system subjected to the influence of the screw–nut joint stiffness, a variable-coefficient lumped parameter model of the system is developed. This model is established taking into account the screw–nut joint stiffness under three different strategies: (1) considering the preload and the weight of the spindle system, (2) considering the elastic deformation but ignoring the effect of the weight, and (3) a perfectly rigid model. The differences between the three models in predicting the position-dependent dynamic characteristics of the system are compared, revealing that the stiffness of screw–nut joint greatly affects the vibratory behavior of the spindle system in the transmission direction. A set of conducted experimental results demonstrate that the stiffness model under the preload and the weight of the spindle system is the most accurate model for the prediction of the position-dependent natural frequency and displacement response of the system with the spindle system position. Therefore, it is more suitable for structure design, performance simulation, and evaluation of a vertical ball screw feed system without counterweight.

China Spallation Neutron Source (CSNS) is a high intensity proton accelerator-based facility. Its accelerator complex includes two main parts: an H- linac and a rapid cycling synchrotron (RCS). The RCS accumulates an 80 MeV proton beam and accelerates it to 1.6 GeV, with a repetition rate of 25 Hz. The AC dipole of the CSNS/RCS is operated at a 25 Hz sinusoidal alternating current which causes severe vibration. The vibration will influence the long-term safety and reliable operation of the magnet. The CSNS/RCS AC dipole-girder system takes vibration isolator to decrease the vibratory force and the vibration amplitude of the dipole. For the long-term safety and reliable operation of the dipole, it is very important to study the dynamic characteristics of the dipole-girder system. This paper takes the dipole-girder as a specific model system. A method for studying the dynamic characteristics of the system is put forward by combining theoretical calculation with experimental testing. The modal parameters with and without vibration isolator of the dipole-girder system are obtained through ANSYS simulation and testing. Then, the dynamic response of the system is calculated with modal analysis and vibration testing data. With the simulation and testing method, the dynamic characteristics of the AC dipole-girder are studied.

Users' cooling needs also change as the outdoor climate continues to change. In order to ensure the cooling demand and timely grasp the cooling capacity transmission situation and the dynamic characteristics of the heating system of the cooling pipeline network, a simulation model was built to analyze the time delay of the cooling capacity transmission and the influence of the chilled water supply flow rate and temperature on the cooling system. The results show that the chilled water supply temperature has almost nothing to do with the time delay of cold transport, and the chilled water supply flow is the main factor affecting the user's time delay, and the lower the system load, the smaller the chilled water supply flow and the longer the cold transport time. The system load decreases by 10% step, and the cooling capacity of the pipe network, cooling capacity of a chiller, power consumption of the chiller and return water temperature of the cold station gradually decrease with time. The step of chilled water supply temperature increases by 10%, and the step of chilled water supply flow decreases by 10%. The cooling capacity of the system, the cooling capacity of the cooler, the power consumption of the cooler and the return water temperature of the cold station gradually increase with time. Moreover, the system transition time is longer when the chilled water temperature and water supply flow are disturbed simultaneously.

As for the vibration problem of rotor system for large rotating machinery such as aero engines, a finite element model for dynamic similarity experiment system of rotor is established based on finite element theory. The effect of support stiffness and support position on the dynamic characteristics of the rotor system have been emphatically analyzed. Moreover, the effect of support stiffness on the dynamic characteristics of rotor system have been verified on the designed test rig. The results show that, under different support stiffness intervals, each order natural frequency of the rotor system has a different variation tendency with the support stiffness or position. In addition, the variation of the mode shapes with the support stiffness or position are closely related to the variation of the natural frequencies with the support stiffness and position. Combining with the practice, the natural frequencies of the rotor system can be reasonably designed and the harmful mode shapes can be avoided by adjusting the supporting characteristics of the rotor system.

Nonlinear dynamic and energetic characteristics of piezoelectric energy harvester with two rotatable external magnets

A hybrid transient CFD-thermoelectric numerical model for automobile thermoelectric generator systems

Response of a simplest servo system to an input perturbation is considered for two variants of correction of a servo drive to provide its stability and controllability. Numerical computations made it possible to find out the effect of the main parameters of the system on the dynamic characteristics of the control system.

The performance of high-speed and high-precision machine tool spindle is quite sensitive to the variation of system parameters. How to accurately predict the influences of key parameters on spindle characteristics is important for designers to achieve required machining accuracy. In the assembly of spindle system, the interference fit, which is always used to connect bearing and shaft, affects the performances of spindle system directly. Therefore, the quantitative investigation on the effects of interference fit on spindle characteristics are of great practical significance. In this paper, the effect mechanism of interference fit on spindle bearing system is explored and used to modify the analytical spindle bearing model. Firstly, the internal geometric relationships among the assembly bearing parts and shaft is analyzed under the influence of assembly deformation and centrifugal expansion. Then, the static and dynamic characteristics of spindle bearing system, including the bearing stiffness, maximum loosing speed, spindle stiffness as well as modal characteristics, are predicted under different interference fit values based on the modified spindle bearing model. The results show that the interference fit will stiffen the bearing and spindle system and result in obvious increments on bearing stiffness, spindle stiffness as well as the natural frequencies. A specially designed spindle test rig is built to verify the simulation results, and the variation of spindle stiffness and natural frequencies are measured under different interference fit values. The maximum error of the system natural frequencies between the analytical results and the experimental data is 7.36%, which confirmed the accuracy of the proposed analytical model.