- Research Article
348
- 10.1016/j.joule.2020.03.004
GeTe Thermoelectrics
- Apr 02, 2020
- Joule
- Xinyue Zhang + 5 more +5
GeTe Thermoelectrics
Liquid-like superionic conductors, with highly mobile ions in a rigid framework, offer intrinsically low lattice thermal conductivity without compromising electronic transport. Argyrodite-type Ag8SnSe6 exhibits a melt-like Ag sublattice that drives lattice thermal conductivity (κL) below 0.2 watts per meter per kelvin, yet its low carrier concentration limits the power factor. Here, interstitial Ag atoms raise the Fermi level into the conduction band, substantially increasing the electron concentration. Simultaneously, the formation of a secondary Ag2Se phase generates lattice distortions that enhance phonon scattering. A pronounced mismatch between electronic (~200 nanometers) and phononic (~0.22 nanometers) mean free paths decouples charge and heat transport, enabling concurrent suppression of κL and retention of high electrical conductivity. This coupled electronic-phononic modulation yields a record ZT of 0.72 at ambient temperature and a peak ZT of 1.1 at 735 kelvins, with an average ZTavg of 0.72 over 320 to 735 kelvins. A unicouple device achieves 6.3% efficiency under a 357-kelvin gradient, highlighting a practical strategy for high-performance midtemperature thermoelectrics.
GeTe Thermoelectrics
GeTe Thermoelectrics
Low lattice thermal conductivities and good thermoelectric performance of hexagonal antiperovskites X(Ba & Sr)3BiN with quartic anharmonicity.
Antiperovskites are a burgeoning class of semiconducting materials that showcase remarkable optoelectronic properties and catalytic properties. However, there has been limited research on their thermoelectric properties. Combining first-principles calculations, self-consistent phonon theory and the Boltzmann transport equation, we have discovered that the hexagonal antiperovskites X(Ba & Sr)3BiN exhibit strong quartic lattice anharmonicity, where the anharmonic vibrations of the light N atoms primarily affect the lattice thermal conductivity (κL) along the c-axis direction. As a result, the lattice thermal conductivities along the a(b)-axis direction are low. At 300 K, the κL values of Ba3BiN and Sr3BiN are only 1.27 W m-1 K-1 and 2.24 W m-1 K-1, respectively. Moreover, near the valence band maximum, the orbitals of the N atoms dominate. This dominance allows Sr3BiN to achieve high power factor under p-type doping, resulting in an impressive thermoelectric figure of merit (ZT) of 0.94 along the c-axis direction at 800 K. In the a(b)-axis direction, at 800 K, n-type doped Ba3BiN exhibits a ZT value of 1.47, surpassing that of traditional thermoelectric materials. Our research elucidates that the hexagonal antiperovskites X(Ba & Sr)3BiN represent a category of potential thermoelectric materials with pronounced anisotropy, low thermal conductivity, and high thermoelectric performance.
Read moreUnconventional lattice thermal transport and high thermoelectric performance in eight alkali-metal half-Heusler compounds A Mg X ( A = Li , Na, K, Rb; X = As , Sb, Bi)
Understanding the lattice dynamical behavior responsible for anomalous lattice thermal conductivity is crucial for the discovery and design of materials with intrinsically low lattice thermal conductivity, thereby enabling high thermoelectric performance. In this work, we employ the harmonic approximation, self-consistent phonon theory, and the self-consistent phonon theory including bubble diagrams (SCPB) to correct phonon self-energy and renormalize phonon frequencies at various theoretical levels. Based on different theoretical foundations, phonon transport behaviors of eight half-Heusler (HH) compounds are systematically calculated within the Wigner transport framework. Multivalley conduction band minimum with varying effective masses lead to the coexistence of high Seebeck coefficients and electrical conductivity. However, moderate spin-orbit coupling (SOC) significantly narrows the band gap, reduces valence band degeneracy, and flattens dispersion, strongly affecting electronic transport. In this study, (i) the SCPB method captures lattice thermal conductivity with minimal deviation from experimental values by including both particle-like and wavelike phonon contributions, underscoring the necessity of bubble diagram corrections in strongly anharmonic materials; (ii) a multidimensional analysis reveals the physical origin of distinct rattling-like behavior observed only in KMgAs, KMgSb, and RbMgSb among the studied HH compounds; (iii) a correlation between phonon bandwidth, phonon band gap, and phonon-phonon scattering is established, offering an efficient approach to qualitatively infer phonon lifetimes from the phonon spectra; (iv) even relatively small wavelike phonon contributions significantly affect the temperature dependence of lattice thermal conductivity; and (v) SOC significantly influences the electronic properties of HH compounds (35.7--$50.0%$), even without heavy elements, challenging the conventional belief that SOC can be ignored in materials lacking heavy atoms.
Read moreTl2XY (X, Y = S, Se) monolayers with low lattice thermal conductivity and high thermoelectric performance by full-band approach with four scattering mechanisms
The low lattice thermal conductivity and high thermoelectric performance of the Janus Tl2SSe monolayer in the temperature region of 300–700 K are identified based on the thermoelectric properties of the Tl2S2, Tl2SSe, and Tl2Se2 monolayers. The transport coefficients for carrier concentrations and temperatures are obtained by solving the linearized Boltzmann transport equation in a full-band electronic structure. Four scattering mechanisms of acoustic deformation potential, optical deformation potential, polar optical phonon, and ionized impurity scatterings are considered. The ionized impurity scattering is recognized as the most important. The lattice thermal conductivity of the Janus Tl2SSe monolayer is substantially smaller than those of the Tl2S2, Tl2Se2 monolayers with higher symmetry. Moreover, we find that the Janus structures of the Tl2SSe monolayer increase the dielectronic constants and enhance the polar optical phonon scattering, then reduce the power factor to some extent. Therefore, the lattice thermal conductivity actually couples with the transport coefficient and cannot be individually regulated as is usually assumed. However, the ZT value of the Tl2SSe monolayer can still reach 1.77 at 700 K even if the intrinsic concentration and the bipolar effect are included. Therefore, the Tl2SSe monolayer is expected to be a promising candidate for thermoelectric materials.
Read moreα-Bi2Sn2O7: A Potential Room Temperature n-type Oxide Thermoelectric
Interest in oxide thermoelectrics has been building due to their high thermal stability and earth-abundant constituent elements. However, the thermoelectric efficiency of flagship oxide materials remains comparatively low, and most materials only reach the maximum figure of merit, ZT, at very high temperatures, above those where the majority of low-grade industrial heat is emitted. It is important to identify thermoelectrics with high conversion efficiency closer to room temperature, particularly for lower-temperature applications such as in domestic heating, consumer electronics and electric vehicles. One of the main factors limiting the efficiency of oxide thermoelectrics is their large lattice thermal conductivities, which has inspired research into more structurally complex materials. In this study, we apply first-principles modelling to assess the low-temperature polymorph of Bi2Sn2O7 (α-Bi2Sn2O7) as a potential thermoelectric material, due to its complex crystal structure, which should suppress phonon transport, and the presence of Bi p and Sn s states in the conduction band, which should yield high electrical conductivity when donor (n) doped. Lattice-dynamics calculations using third-order perturbation theory predict an ultralow room-temperature lattice thermal conductivity of 0.4 W m-1 K-1, the lowest ever predicted for an oxide material, and suggest that nanostructuring to a grain size of 5 nm could further decrease this to 0.28 W m-1 K-1. The ultralow lattice thermal conductivity gives α-Bi2Sn2O7 a maximum ZT of 0.36 at 385 K (0.46 with nanostructuring), which is the highest low-temperature value predicted for an oxide thermoelectric. Most importantly, our analysis highlights the relationship between the structural complexity, the chemical nature of the cation, and the short phonon lifetimes, and thus provides guidelines for identifying other novel high-performance oxide thermoelectrics.
Read moreLow lattice thermal conductivity and high thermoelectric figure of merit in Na2MgSn
Thermoelectric materials enables the harvest of waste heat and directly conversion into electricity. In search of high efficient thermoelectric materials, low thermal conductivity of a material is essential and critical. Here, we have theoretically investigated the lattice thermal conductivity and thermoelectric properties of layered intermetallic Na$_2$MgSn and Na$_2$MgPb based on the density functional theory and linearized Boltzmann equation with the single-mode relaxation-time approximation. It is found that both materials exhibit very low and anisotropic intrinsic lattice thermal conductivity. Despite of the very low mass density and simple crystal structure of Na$_2$MgSn, its lattice thermal conductivities along $a$ and $c$ axes are only 1.75 and 0.80 W/m$\cdot$K respectively at room temperatures. When Sn is replaced by the heavier element Pb, its lattice thermal conductivities decrease remarkably to 0.51 and 0.31 W/m$\cdot$K respectively along $a$ and $c$ axes at room temperatures. We show that the low lattice thermal conductivities of both materials are mainly due to their very short phonon lifetimes, which are roughly between 0.4 to 4.5 ps. Combined with previous experimental measurements, the metallic Na$_2$MgPb can not be a good thermoelectric material. However, we predict that the semiconducting Na$_2$MgSn is a potential room-temperature thermoelectric material with a considerable $ZT$ of 0.34 at 300 K. Our calculations not only imply that the intermetallic Na$_2$MgSn is a potential thermoelectric material, but also can motivate more theoretical and experimental works on the thermoelectric researches in simple layered intermetallic compounds.
Read moreOrigin of the variation in lattice thermal conductivities in pyrite-type dichalcogenides
Lattice thermal conductivity is a crucial parameter for thermoelectric (TE) applications. In pyrite-type metal dichalcogenides, it is observed that the type of metal atom has a significant influence in the phonon properties and lattice thermal conductivities, but the physical origin is not clear. In this paper, we show that, for the pyrite-type posttransition metal (such as Zn or Cd) dichalcogenides, because the fully occupied ${d}^{10}$ orbitals inside the valence bands are relatively localized, the enhanced symmetry-controlled $s\text{\ensuremath{-}}d$ coupling effects in the posttransition metal atoms when they vibrate away from the high-symmetry equilibrium positions can lead to soft phonon properties and strong anharmonicity. Thus, they behave as rattlinglike atoms, and these systems have extremely low lattice thermal conductivities. However, for some pyrite-type transition metal dichalcogenides, when the outermost $d$ electrons in transition metal atoms are only occupied by the ${T}_{2g}$-derived states, such as Fe with ${d}^{6}$ configuration, the symmetry-controlled $s\text{\ensuremath{-}}d$ coupling effects in the transition metal atoms are strongly cancelled by the varying crystal field splitting when symmetry is reduced during vibration. Therefore, these compounds exhibit hard phonon properties, weak anharmonicities, and high lattice thermal conductivities. In this paper, we reveal the electronic origin of the puzzling behaviors of pyrite-type dichalcogenides which show a wide range of thermal conductivity properties. The discussed mechanism can also be used to guide researchers in seeking promising TE materials with low lattice thermal conductivity.
Read moreFlat phonon modes driven ultralow thermal conductivities in Sr3AlSb3 and Ba3AlSb3 Zintl compounds
Searching for compounds with intrinsic low lattice thermal conductivity has been proven a successful strategy for achieving high thermoelectric performance. Herein, employing density functional theory calculations combined with electron and phonon Boltzmann transport theories, we report that Sr3AlSb3 and Ba3AlSb3 within the Zintl 3–1–3 compositional family exhibit record low thermal conductivities of 0.78 and 0.55 W/mK at room temperature, respectively. These low thermal conductivities are rooted in low-energy optical phonon modes with strong anharmonicity and the emergence of high-energy flat optical phonon modes with zero contribution to the lattice thermal conductivity. Heavier cationic atoms are found to soften low-lying optical phonon modes, which enhance phonon scattering and, therefore, favor a lower thermal conductivity. These combined characteristics lead to high and balanced figure of merit values around 2.3 for Zintl Ba3AlSb3 at both optimal p-type and n-type doping and high temperature. Our work highlights the important role of flat optical phonon modes on designing promising thermoelectric materials with intrinsic low thermal conductivity.
Read more(Invited) Reducing the Thermal Conductivity By Driving PbTe to a Phase Transition Via Strain and/or Alloying
The efficient control of thermoelectric energy conversion processes is highly desirable as nearly 60% of the consumed energy is wasted as heat. Low thermal conductivity is one of the key factors leading to high thermoelectric efficiency of a material [1]. However, one of the major obstacles in the design of materials with low lattice thermal conductivity is the difficulty in efficiently scattering phonons across the entire frequency spectrum [2]. Using first principles calculations, we show that driving PbTe materials to the brink of a Peierls-like phase transition could be a powerful strategy to solve this problem. We illustrate this concept by applying tensile [001] strain to PbTe and its alloy with a chemically similar material in the rock-salt structure (e.g. PbSe), and by alloying PbTe with a related material in the rhombohedral, Peierls-distorted, structure (e.g. GeTe). This induces extremely soft optical modes, which increases acoustic-optical phonon coupling and decreases phonon lifetimes at all frequencies. We predict that PbTe, Pb(Se,Te) and (Pb,Ge)Te alloys tuned in the described manner could have substantially reduced lattice thermal conductivity compared to PbTe. The proposed concept may open new opportunities for the development of more efficient thermoelectric materials. This work was done in collaboration with Ronan Murphy, Eamonn Murray and Stephen Fahy. [1] G. J. Snyder and E. S. Toberer, Nature Mater. 7, 105 (2008). [2] K. Biswas et al. Nature 489, 414 (2012).
Read moreLow lattice thermal conductivity by alloying SnTe with AgSbTe2 and CaTe/MnTe
SnTe-AgSbTe2 alloys have shown promising thermoelectric performance due to phonon-vacancy scattering, while SnTe alloyed with high-solubility monotellurides such as CaTe/MnTe has also shown enhanced thermoelectric performance owing to band convergence. However, to what level the combined effect on thermoelectrics by alloying SnTe with AgSbTe2 and CaTe/MnTe exists, especially for the quantitative relationship between the vacancy concentration and lattice thermal conductivity, still remains a mystery. Here, a spontaneous strategy has shown that combining AgSbTe2 with CaTe/MnTe in SnTe alloys can lead to an inherent valence band convergence and improved electronic performance. In particular, a low lattice thermal conductivity (∼0.4 W/m K), which approaches the amorphous limit of SnTe, is achieved in (Sn0.95Ca0.05Te)0.75(AgSbTe2)0.125 with 3% excess of Sn. The Debye-Callaway model provides a good clarification of underlying physics for the reduced lattice thermal conductivity as well as quantifies the contribution of vacancy scattering. The present finding demonstrates the excellent potential for advancing the thermoelectric performance by SnTe-based alloys.
Read moreAccelerated Discovery and Design of Ultralow Lattice Thermal Conductivity Materials Using Chemical Bonding Principles
Semiconductors with very low lattice thermal conductivities are highly desired for applications relevant to thermal energy conversion and management, such as thermoelectrics and thermal barrier coatings. Although the crystal structure and chemical bonding are known to play vital roles in shaping heat transfer behavior, material design approaches of lowering lattice thermal conductivity using chemical bonding principles are uncommon. In this work, an effective strategy of weakening interatomic interactions and therefore suppressing lattice thermal conductivity based on chemical bonding principles is presented and a high‐efficiency approach of discovering low κL materials by screening the local coordination environments of crystalline compounds is developed. The resulting first‐principles calculations uncover 30 hitherto unexplored compounds with (ultra)low lattice thermal conductivities from 13 prototype crystal structures contained in the Inorganic Crystal Structure Database. Furthermore, an approach of rationally designing high‐performance thermoelectrics is demonstrated by additionally incorporating cations with stereochemically active lone‐pair electrons. These results not only provide atomic‐level insights into the physical origin of the low lattice thermal conductivity in a large family of copper/silver‐based compounds but also offer an efficient approach to discover and design materials with targeted thermal transport properties.
Read moreCharge Transport and Thermoelectric Properties of Sn-Doped Tetrahedrites Cu12Sb4-ySnyS13
In this study, tetrahedrite compounds doped with Sn were prepared by mechanical alloying and hot pressing, and their charge transport and thermoelectric properties were analyzed. X-ray diffraction analysis revealed that both the synthetic powders and sintered bodies were synthesized as a single tetrahedrite phase without secondary phases. Densely sintered specimens were obtained with relatively high densities of 99.5%-100.0% of the theoretical density, and the component elements were distributed uniformly. Sn was successfully substituted at the Sb site, and the lattice constant increased from 1.0348 to 1.0364 nm. Positive signs of the Hall and Seebeck coefficients confirmed that the Sn-doped tetrahedrites were p-type semiconductors. The carrier concentration decreased from 1.28 × 1019 to 1.57 × 1018 cm-3 as the Sn content decreased because excess electrons were supplied by doping with Sn4+ at the Sb3+ site of the tetrahedrite. The Seebeck coefficient increased with increasing Sn content, and Cu12Sb3.6Sn0.4S13 exhibited maximum values of 238-270 µVK-1 at temperatures of 323-723 K. However, the electrical conductivity decreased as the amount of Sn doping increased. Thus, Cu12Sb3.9Sn0.1S13 exhibited the highest electrical conductivity of (2.24-2.40) × 104 Sm-1 at temperatures of 323-723 K. A maximum power factor of 0.73 mWm-1K-2 was achieved at 723 K for Cu12Sb3.9Sn0.1S13. Sn substitution reduced both the electronic and lattice thermal conductivities. The lowest thermal conductivity of 0.49-0.60 Wm-1K-1 was obtained at temperatures of 323-723 K for Cu12Sb3.6Sn0.4S13, where the lattice thermal conductivity was dominant at 0.49-0.57 Wm-1K-1. As a result, a maximum dimensionless figure of merit of 0.66 was achieved at 723 K for Cu12Sb3.9Sn0.1S13.
Read moreOptimized Electronic Bands and Ultralow Lattice Thermal Conductivity in Ag and Y Codoped SnTe.
As a lead-free thermoelectric material, SnTe is inhibited by its inherent high carrier concentration and high thermal conductivity. This work describes the synergistic effect on the modulation of band structure and microstructural defects of SnTe by Ag and Y codoping, which gives rise to band convergence and multiple microstructural defects (secondary phases, dislocations, and boundaries) in the matrix and endows Sn0.94Ag0.09Y0.05Te with an increased power factor of ∼2485 μW m-1 K-2, an extremely low lattice thermal conductivity of ∼0.61 W m-1 K-1, and a peak zT as high as ∼1.2 at 873 K. This work reveals that the combination of Ag and Y could play a role in the synergistic optimization of electronic and phonon transport properties of SnTe by modifying the band structure and microstructures, providing guidance for enhancing the thermoelectric performance of the relevant materials.
Read moreSynthesis and thermoelectric properties of p-type double-filled La1−z Ce z Fe4−x Co x Sb12 skutterudites
La1−z Ce z Fe4−x Co x Sb12 (0.25 ≤ z ≤ 0.75 and 0.5 ≤ x ≤ 1) skutterudites were synthesized, and the effects of La/Ce double filling and Co substitution on their transport and thermoelectric properties were examined. The formation of the skutterudite phase was confirmed and a small amount of secondary phases of FeSb2 and (La,Ce)Sb2 were observed. The lattice constant decreased with increasing Co and Ce contents, which meant that the substitution of Co for Fe and the filling of La and Ce had been successfully performed. All samples showed p-type characteristics with positive signs of the Hall coefficient and the Seebeck coefficient. The carrier concentration (the electrical conductivity) decreased with increasing Co and Ce contents due to the increased charge compensation and electron donation. The lattice thermal conductivity decreased with decreasing Co substitution, but the total thermal conductivity increased with decreasing Co substitution because the electronic thermal conductivity was dominant. La/Ce-double-filled La1−z Ce z Fe4−x Co x Sb12 skutterudites showed superior thermoelectric properties to La- or Ce-single-filled skutterudites due to their improved electrical properties and low lattice thermal conductivity. The maximum dimensionless figure of merit ZT = 0.79 was achieved at 823 K for La0.75Ce0.25Fe3.5Co0.5Sb12.
Read moreFirst-Principles Investigation of the Effect of Vacancy Defects and Carbon Impurities on Thermal Conductivity of Uranium Mononitride (UN)
Uranium mononitride (UN) is a promising nuclear fuel with a high melting point, high thermal conductivity, and low coefficient of thermal expansion. Theoretical studies of UN can provide insights on its thermal transport mechanism, which is of great significance for the design and application of UN fuel. During the processing and operation, crystal defects and impurities, such as vacancies and carbon impurities, potentially arise in the nuclear fuel, which probably affect the thermomechanical properties of UN. To figure out the effect of vacancy defects and carbon impurities on the thermal conductivity of UN, density functional theory and Boltzmann transport theory are applied to conduct a theoretical investigation on the mechanical and thermal properties of ideal and defective UN. The calculated results show that in the case of UN with a U or N vacancy, both the lattice and electronic thermal conductivity are decreased, compared with the ideal case. With a carbon atom occupying the N site in the lattice, the electronic thermal conductivity is reduced but the lattice thermal conductivity is increased. Combining the results of lattice and electronic thermal conductivity, the total thermal conductivities of three defective states are lower than the ideal UN. The thermal conductivities of UN with a U vacancy (13.91 W/mK), N vacancy (15.36 W/mK), and a carbon atom occupying the N site (15.14 W/mK) are, respectively, reduced by 25.7%, 18.0%, and 19.2%, in comparison with ideal result (18.73 W/mK) at 1000 K.
Read more