Enhanced disordering of GaAs/AIGaAs multiple quantum well by rapid thermal annealing using plasma enhanced chemical vapour deposited SiN capping layer grown at high RF power condition
The multiple quantum well (MQW) structure is a good candidate to monolithically integrate lasers and waveguides for realizing photonic integrated circuits. For such an application, selective disordering techniques are required, because these can make it possible to define a waveguide section laterally by inducing local changes in absorption and refractive indices of a MQW structure, which is needed to fabricate waveguide devices including laser. There are several techniques to selectively disorder the I I I -V MQW structures. These are impurity induced disordering [1,2], ion implantation disordering [3, 4], and impurity-free disordering [5-12] followed by thermal treatment. Impurity induced disordering and ion implantation disordering can disorder MQW structure perfectly, but these techniques introduce many defects and high doping concentrations which may deteriorate the performances of waveguide devices because of losses from scatterings by defects and free carrier absorption in the waveguide. Impurity-free techniques employ dielectrics, such as SiO2 or SiN, a capped annealing technique, which employs rapid thermal annealing (RTA) [5-10] or sealed ampoule annealing with an As overpressure [11, 12]. Impurity-free techniques do not disorder MQW structure completely, but disorder it enough to fabricate waveguides and lasers [9-12]. For impurity-free disordering, there are various film growth techniques, such as chemical vapour deposition (CVD) [11], e-beam evaporation [6, 8, 9], sputtering [5], and plasma enhanced chemical vapour deposition (PECVD) [7, 10, 12], which can deposit SiN and/or Si te films on a MQW structure. The behaviour of disordering is affected by the film quality used in the impurity-free disordering technique. Therefore, if an optimum film growth condition can be found by varying process conditions, then selective disordering can be achieved with the same material without surface degradation which should be accompanied in the disordering process without an encapsulation. The characteristics of film deposited by the PECVD technique can be varied by varying process conditions, such as substrate temperature, ratio of reactant gas, and RF power [13]. As a first step to finding a process-dependent impurity-free disordering, we varied the RF power. We carried out impurity-free disordering using a PECVD SiN cap layer with RTA. We found that this technique could disorder the GaAs/A1GaAs MQW structure and the disordering was enhanced by using SiN film grown at high RF power. We used a GaAs/A1GaAs MQW laser structure which was grown by a metal organic chemical vapour deposition (MOCVD) technique on Si-doped n ÷ GaAs substrate. The structure has the following layers from the top of the substrate: 0.5/xm of n (1018 cm -3) GaAs buffer, 1/zm of n (1017 cm -3) A10.4~Ga0.s3As, 0.1/xm of undoped A10.24Ga0.76As, four 7 nm undoped GaAs quantum wells with 10 nm A10.24Ga0.76As barrier, 0.1/xm of undoped A10.24Ga0.76As, 1/zm of p (1017 cm -3) A10.47Ga0.53As, and 0.2/xm of p+ (10 ~8 cm -3) GaAs. In the substrate design, separate confinement design is chosen to enhance the optical confinement in the quantum wells. SiN films were deposited by a PECVD technique for cap layers. We used dilute silane (5% Sill4 in N:) and high purity NH 3 (99.999%) and N2 (99.9999%) as a reactant gas. During plasma deposition, the ratio of partial pressure (PNH3/Psi~,) was kept at 1, total pressure was kept as 120 Pa by adding N2 gas and the substrate temperature was 300 °C. SiN films were grown with various RF powers (0 W, 60 W and 90 W). The thicknesses and refractive indices, for each RF power condition, were determined by an ellipsometer (Gaertner, Ll17) and a surface profiler (Tencor, alpha step 200). Disordering of MQW samples was accomplished by RTA at 850 °C for 35 s in Ar atmosphere with a heating rate of 65 °C/s. Disordering of MQW
Read more
2