Energy-Efficiency Analysis and Optimization for Virtual-MIMO Systems

Cognitive radio is hailed as the best possible solution for the problem of spectrum under-utilization. Pure Cognitive Radio Networks are unreliable in nature, hence a Hybrid Cognitive Radio Network using both Cognitive and licensed radio resources is more useful in practical. This paper analyses the performance of Hybrid Cognitive Gaussian Relay Channel (HCGRC) for underlay condition, considering the interference constraint at the nearest primary user. The performance metrics such as Capacity, Energy Efficiency and Spectral Efficiency are formulated and computed using numerical simulations with and without Rayleigh fading. These results are helpful in determining optimum power and bandwidth allocation within allowed interference to achieve full Capacity. The study of HCGRC for underlay approach leads to two key observations. First, for given primary user's location, the upper limit of power allocation for Cognitive relay can be determined. Second, Spectral Efficiency can be maximized by allocating optimum bandwidth to achieve peak capacity. The numerical results predict the optimal value of resources for achieving maximum Capacity, Energy Efficiency and Spectral Efficiency.

Equal allocation of bandwidth and/or power may not be efficient for wireless multi-user networks with limited bandwidth and power resources. Optimal joint bandwidth and power allocation strategies for wireless multi-user networks with and without relaying are proposed in this paper for (1) the maximization of the sum capacity of all users; (2) the maximization of the worst user capacity; and (3) the minimization of the total power consumption of all users. It is shown that the proposed allocation problems are convex and, therefore, can be solved efficiently. Moreover, joint bandwidth and power allocation for admission control is considered. A suboptimal greedy search algorithm is developed to solve the admission control problem efficiently. Instructive analysis of the greedy search shows that it can achieve good performance, and the condition under which the greedy search is optimal is derived. The formal and in-depth analysis of the greedy search algorithm presented in this paper can serve as a benchmark for analyzing similar algorithms in other applications. The performance improvements offered by the proposed optimal joint bandwidth and power allocation are demonstrated by simulations. The advantages of the suboptimal greedy search algorithm for admission control are also shown in numerical results.

A novel multibeam satellite system design is proposed in this paper based on jointly optimizing power and carrier allocation in order to best match the asymmetric traffic requests. This design introduces higher and asymmetric interference levels throughout the coverage. However, both power and bandwidth will be used more efficiently. Even though the problem of power and bandwidth allocation has been addressed in terrestrial wireless communications, it is new in satellite systems and since architecture and channel are different, available results and algorithms are not applicable to satellite payload systems. In this paper we formulate the resource allocation problem as max-min SINR balancing based on the recently introduced axiomatic-based interference model, but in addition, we also optimize the carrier allocation when performing the SINR balancing problem. An analytical solution for the optimal carrier allocation is proposed and we iteratively find the optimal power allocation for each beam. The Shannon (upper bound) and current state-of-the art PHY layer technology: DVB-S2 are proposed to be implemented in order to obtain the gap between them. Simulation results show significant improvements in terms of power gain, spectral efficiency and traffic matching ratio comparing with conventional system, which is designed based on uniform bandwidth and power allocation.

With the drastic increase of space information network (SIN) traffic and the diversity of network traffic types, the optimal allocation of the scarce network resources is of great significance for optimizing the SIN system capability. In this paper, we propose a multi-resource management method for multi-tier SIN using the cooperative Nash bargaining solution. Since the original problem is a non-convex problem, we firstly make logarithmic transition, and then find a tightest lower bound function to convert the initial problem into a convex one. In order to carry out the optimal bandwidth and power allocation in SIN, we construct a joint bandwidth and power allocation (JBPA) algorithm. Simulation results show the performance improvement of the JBPA scheme and the convergence of JBPA algorithm.

In fifth-generation cellular networks (5G), a large multiple-input multiple-output (MIMO) technique is critical for optimizing the trade-off between energy efficiency (EE) and spectral efficiency (SE). The challenges for the next generation depend on increasing the high data traffic in the wireless communication system for both EE and SE. The trade-off between EE and SE in downlink massive MIMO systems has been investigated in this paper using the first derivative of transmit antennas and transmit power. The EE-SE trade-off has been investigated using a multi-objective optimization problem to reduce transmit power. The EE and SE based on constraint maximum transmits power allocation and a number of antennas by computing the first derivative of transmit power to maximize the trade-off EE - SE has been improved. The optimal trade-off between EE and SE can be obtained based on the first derivative by selecting the optimal antennas with a low cost of transmit power showing good simulation results. Therefore, based on an optimal optimization problem is flexible to make trade-offs between EE-SE for distinct preferences.

For data services over satellite networks, the efficient management of satellite downlink communication resources is crucial for economic competitiveness of the medium. To support a broad spectrum of users with small terminals at high rates, narrow transmit spotbeams on the satellite will be used. Since satellite transmitter resources are expensive and there can be many spotbeam-coverage cells within the satellite service area, it is attractive to use some form of agile scanning beam system and to time-share these precious resources. An optimized design of the multibeam antenna pattern and scheduling can further improve the efficiency of transmission and power management. In this paper, the advantage of parallel multibeams in terms of spectral efficiency and power gain is shown, and the issue of multibeam power allocation based on traffic demands and channel conditions over satellite downlinks with power and delay constraints is addressed. The study indicates that the use of a parallel multibeam scheme with optimum power allocation can achieve a substantial power gain and reasonable proportional fairness. By coupling power allocation with multibeam scheduling when the number of active beams is smaller than the number of cells, the authors show that a modest number of active parallel beams are sufficient to cover many cells efficiently.

This chapter is attempted to provide a survey of the advanced concepts and related issues involved in Multiple Input Multiple Output (MIMO) systems. MIMO system technology has been considered as a really significant foundation on which to build the next and future generations of wireless networks. The chapter addresses advanced MIMO techniques such as polarization diversity and antenna selection. We gradually provide an overview of the MIMO features from basic to more advanced topics. The first sections of this chapter start by introducing the key aspects of theMIMO theory. TheMIMO systemmodel is first presented in a genericway. Then, we proceed to describe diversity schemes used in MIMO systems. MIMO technology could exploit several diversity techniques beyond the spatial diversity. These techniques essentially cover frequency diversity, time diversity and polarization diversity. We further provide the reader with a geometrically based models for MIMO systems. The virtue of this channel modeling is to adopt realisticmethods for modeling the spatio-temporal channel statistics from a physical wave-propagation viewpoint. Two classes for MIMO channel modeling will be described. These models involve the Geometry-based Stochastic ChannelModels (GSCM) and the Stochastic channel models. Besides the listedMIMO channel models already described, we derive and discuss capacity formulas for transmission over MIMO systems. The achieved MIMO capacities highlight the potential of spatial diversity for improving the spectral efficiency of MIMO channels. When Channel State Information (CSI) is available at both ends of the transmission link, the MIMO system capacity is optimally derived by using adaptive power allocation based on water-filling technique. The chapter continues by examining the combining techniques for multiple antenna systems. Combining techniques are motivated for MIMO systems since they enable the signal to noise ratio (SNR) maximization at the combiner output. The fundamental combing techniques are the Maximal Ratio Combining (MRC), the Selection Combining (SC) and the Equal Gain Combining(EGC). Once the combining techniques are analyzed, the reader is introduced to the beamforming processing as an optimal strategy for combining. The use of multiple antennas significantly improves the channel spectral efficiency. Nevertheless, this induces higher system complexity of the communication system and the communication system performance is effected due to correlation between antennas that need to be deployed at the same terminal. As such, the antenna selection algorithm for MIMO systems is presented. To elaborate on this point, we introduce Space time coding techniques for MIMO systems and we evaluate by simulation the performance of the communication system. Next, we emphasis on multi polarization techniques for MIMO systems. As a background, we presume that the reader has a thorough understanding of antenna theory. We recall the basic antenna theory and concepts that are used throughout the rest of the chapter. We rigorously introduce the 3D channel model over the Non-Line of Sight (NLOS) propagation channel for MIMO system with polarized antennas. We treat the depolarization phenomena and we study its effect on MIMO system capacity. The last section of the chapter provides a scenario for collaborative sensor nodes performing distributed MIMO system model which is devoted to sensor node localization in Wireless Sensor Networks. The localization algorithm is based on beamforming processing and was tested by simulation. Our chapter provides the reader by simulation examples for almost all the topics that have been treated for MIMO system development and key issues affecting achieved performance.

Spectral efficiency and energy efficiency of distributed antenna systems with virtual cells

This paper presents an optimal energy-efficient power allocation scheme for a point-to-point multicarrier link over frequency-selective fading channel subject to a delay-outage probability constraint. For a target delay-outage limit, the energy efficiency (EE) objective function is formulated as the ratio of the achieved link effective capacity to the total expenditure power, expressed in units of b/J/Hz. We first prove that this objective function is quasi-concave in the transmission power, and, hence, the global maximum solution of the underlying optimization problem can be obtained using fractional programming. Subsequently, we develop a two-step optimal power allocation algorithm by first obtaining the average sum power level corresponding to the maximum achievable EE, followed by jointly distributing this obtained average power over time and frequency. Analytical results show that the EE-based power allocation has a structure similar to that of the QoS-driven spectral-efficient scheme, but with a different cut-off threshold below which no transmission power is allocated. Simulation results show that the proposed joint optimal power allocation scheme provides significant EE gains over the simple independent subcarrier optimization scheme, where these performance advantages become more pronounced with tighter delay constraints and in fading channels with more severe frequency selectivity.

Wireless federated learning (WFL) undergoes a communication bottleneck in uplink, limiting the number of users that can upload their local models in each global aggregation round. This paper presents a new multi-carrier non-orthogonal multiple-access (MC-NOMA)-empowered WFL system under an adaptive learning setting of Flexible Aggregation. Since a WFL round accommodates both local model training and uploading for each user, the use of Flexible Aggregation allows the users to train different numbers of iterations per round, adapting to their channel conditions and computing resources. The key idea is to use MC-NOMA to concurrently upload the local models of the users, thereby extending the local model training times of the users and increasing participating users. A new metric, namely, Weighted Global Proportion of Trained Mini-batches (WGPTM), is analytically established to measure the convergence of the new system. Another important aspect is that we maximize the WGPTM to harness the convergence of the new system by jointly optimizing the transmit powers and subchannel bandwidths. This nonconvex problem is converted equivalently to a tractable convex problem and solved efficiently using variable substitution and Cauchy’s inequality. As corroborated experimentally using a convolutional neural network and an 18-layer residential network, the proposed MC-NOMA WFL can efficiently reduce communication delay, increase local model training times, and accelerate the convergence by over 40%, compared to its existing alternative.

Cell-free massive multiple-input multiple-output (CF-mMIMO) has attracted considerable attention due to its potential for delivering high data rates and energy efficiency (EE). In this paper, we investigate the resource allocation of downlink in CF-mMIMO systems. A hierarchical depth deterministic strategy gradient (H-DDPG) framework is proposed to jointly optimize the access point (AP) clustering and power allocation. The framework uses two-layer control networks operating on different timescales to enhance EE of downlinks in CF-mMIMO systems by cooperatively optimizing AP clustering and power allocation. In this framework, the high-level processing of system-level problems, namely AP clustering, enhances the wireless network configuration by utilizing DDPG on the large timescale while meeting the minimum spectral efficiency (SE) constraints for each user. The low layer solves the link-level sub-problem, that is, power allocation, and reduces interference between APs and improves transmission performance by utilizing DDPG on a small timescale while meeting the maximum transmit power constraint of each AP. Two corresponding DDPG agents are trained separately, allowing them to learn from the environment and gradually improve their policies to maximize the system EE. Numerical results validate the effectiveness of the proposed algorithm in term of its convergence speed, SE, and EE.

Conventional designs on two-way relay networks mainly focus on the spectral efficiency (SE) rather than energy efficiency (EE). In this paper, we consider a system where two source nodes communicate with each other via an amplify-and-forward (AF) relay node and study the power allocation schemes to maximize EE while ensuring a certain data rate. We propose an optimal energy-efficient power allocation algorithm based on iterative search technique. In addition, a closed-form suboptimal solution is derived with reduced complexity and negligible performance degradation. Numerical results show that the proposed schemes can achieve considerable EE improvement compared with conventional designs.

In this paper, the power allocation problem for downlink massive multiple-input multiple-output (MIMO) systems with inter-user interference is investigated considering the tradeoff between energy efficiency (EE) and spectral efficiency (SE). The minimum mean-square-error channel estimate and the rigorous closed-form expression of achievable downlink rate are first derived. Then, the multi-objective optimization problem (MOP) is formulated subject to maximum total transmission power constrain, where conflicting EE and SE are maximized simultaneously. To obtain the solution set characterized as a Pareto set, the MOP is transformed into a single-objective problem (SOP) using weighted sum method. We further convert the SOP into a convex optimization problem by adding an additional interference constraint, and the optimal power allocation algorithm is proposed by using dual method to balance EE and SE efficiently. Simulation results demonstrate the effectiveness of the proposed algorithm and illustrate the fundamental tradeoff between EE and SE for different parameter settings.

Large-scale multiple-input multiple-output (MIMO) communication systems can bring substantial improvement in spectral efficiency and/or energy efficiency, due to the excessive degrees-of-freedom and huge array gain. However, large-scale MIMO is expected to deploy lower-cost radio frequency (RF) components, which are particularly prone to hardware impairments. Unfortunately, compensation schemes are not able to remove the impact of hardware impairments completely, such that a certain amount of residual impairments always exists. In this paper, we investigate the impact of residual transmit RF impairments (RTRI) on the spectral and energy efficiency of training-based point-to-point large-scale MIMO systems, and seek to determine the optimal training length and number of antennas which maximize the energy efficiency. We derive deterministic equivalents of the signal-to-noise-and-interference ratio (SINR) with zero-forcing (ZF) receivers, as well as the corresponding spectral and energy efficiency, which are shown to be accurate even for small number of antennas. Through an iterative sequential optimization, we find that the optimal training length of systems with RTRI can be smaller compared to ideal hardware systems in the moderate SNR regime, while larger in the high SNR regime. Moreover, it is observed that RTRI can significantly decrease the optimal number of transmit and receive antennas.

This paper studies the challenge of efficient resource allocation in wireless networks by investigating the potential benefits of cognitive radio networks (CRN) and non‐orthogonal multiple access (NOMA) techniques. Specifically, the purpose of this paper is to explore user pairing and power allocation in a multiuser cooperative CRN‐NOMA network. To achieve the goal, a novel user pairing algorithm with reinforcement learning (RL) is proposed to adaptively select the optimal group for pairing according to the factors such as channel gain, distances, and angles. A user group is consisted of a primary user (PU) and up to three secondary users (SUs). The key findings of this paper highlight the effectiveness of RL in optimizing power allocation while considering various constraints. As a result, significant improvements in network throughput and user fairness are achieved. Compared with the classical power allocation algorithms (i.e., equal power allocation, proportional power allocation, iterative power allocation, and iterative water‐filling power allocation), the proposed power allocation based on RL algorithm and iterative water‐filling power allocation algorithm have better performance in terms of throughput, fairness, spectrum efficiency, and energy efficiency. In addition, compared with the iterative water‐filling power algorithm, the proposed algorithm improves the throughput by 31.71% and obtains twice the spectrum efficiency and energy efficiency. The simulation results consistently show that the proposed method has advantages in enhancing PU capacity. Further advancements in this field of research are encouraged based on the promising outcomes of this study.