Energy-Efficient D2D Communication under Downlink HetNets

Joint modulation-coding scheme (MCS) adaptation and resource block (RB) allocation is an effective approach to guarantee different quality of service (QoS) requirements of all UEs under dynamic network environments. In this paper, we consider a fifth generation (5 G) cellular network with time-varying wireless channels, in which the BS serves multiple user equipments (UEs) under limited available RBs. We aim to minimize the total RB consumption subject to the rigorous constraints of each UE's QoS requirement. To attain this objective, this paper puts forth an online learning technique, referred to as integrated Deep Reinforcement learning and stable Matching (DeepRM), in the sense that the MCS adaptation and RB allocation decisions are conducted without acquiring the real-time channel quality indicator (CQI) feedback. DeepRM is a closed-loop framework, where the output of deep reinforcement learning (DRL) is imported into the stable matching to guide optimal RB allocation whilst the output of stable matching is fed into the DRL framework to assist efficient MCS decision-making. Specifically, in DeepRM, we first develop a powerful DRL algorithm, termed as Action-and-Reward Branching Deep Q-network (ARBDQ), by incorporating the action branch architecture into conventional DRL and modifying the traditional deep neural network training mechanism, to perform judicious MCS decisions on different links in parallel. Then, a new many-to-one stable matching algorithm, called adaptive deferred acceptance, is exploited to dynamically adjust the RB quota of each UE in a computationally efficient fashion. Simulation results demonstrate that compared with ACO-HM, OLLA-ADA, and ARBDQ-Random algorithms, DeepRM induces much less RB consumption while guaranteeing the QoS requirements of all UEs in various network scenarios. Furthermore, under miscellaneous QoS requirement, number of UEs, and CQI reporting period setups, DeepRM is more robust than other baselines.

In heterogeneous cellular networks (HCNs), the growing demand of small cell data traffic puts great pressure on the capacity limited backhaul links. Resource allocation is an efficient approach to mitigate the severe interference and improve the network performance in HCNs. However, differentiated backhaul capacity constraints introduce the inherent nonconvexity to the resource optimization problem, which hinders the development of the optimal solutions. In this article, we investigate the joint resource block (RB) and power allocation problem under two different backhaul capacity limitations. First, we consider the small cell backhaul limitation scenario where the backhaul capacity constraint is imposed on each small cell. Then, we extend the resource optimization to the macrocell base station backhaul limitation scenario which considers the overall backhaul capacity constraint on the whole small cell network. Besides, the quality of service (QoS) requirements of users and the cross‐tier interference mitigation are also considered. This resource allocation problem is formulated as a nonconvex mixed‐integer nonlinear programming (MINLP) problem. By variable substitution and constraints relaxation, we convert the original optimization problem into a convex one and obtain the optimal solutions. Accordingly, joint RB and power allocation algorithms are proposed. Numerical results verify the effectiveness of the proposed algorithms and evaluate the impact of different types of backhaul capacity limitations on system performance.

A third‐generation partnership project long‐term evolution system uses the concept of a 2‐tier heterogeneous network, where low‐power and short‐range femtocells are laid under macrocells to fulfill the quality of service (QoS) requirements of users and to boost overall network throughput. However, cochannel deployment gives rise to the problem of cross‐tier interference that significantly deteriorates the performance of the cellular network. The coordinated multipoint (CoMP) transmission scheme is proposed as a promising solution to alleviate cross‐tier interference by doing cooperation among the neighbor base stations. In this paper, we propose a QoS priority‐based coordinated scheduling and hybrid spectrum access (QoS‐CSaHSA) scheme for downlink CoMP transmission in 2‐tier networks. The proposed QoS‐CSaHSA scheme dynamically reduces the femtocells' power requirements by considering the neighbor cell interference, and it also balances the macrocell load by switching the femtocells to HA mode. Moreover, it can reduce unnecessary muting of the base stations because it only enables the coordinated scheduling CoMP when there is no other possibility to reduce the cross‐tier interference. System‐level simulation results prove the validity of the proposed QoS‐CSaHSA scheme in a heterogeneous network environment. Compared with the existing schemes that operate the femtocells in a closed‐subscriber group without considering users' QoS requirements, the proposed scheme almost doubles the cell‐edge user throughput and reduces the packet loss rate and call‐blocking probability.

Cross-layer based asymmetric resource allocation in relay-aided cognitive radio networks (CRN) is proposed in this paper. Existing cross-layer schemes on relay-aided CRN are based on symmetric resource allocation (RA) where the transmission duration is assumed to be symmetric between secondary base station (BS) to relay station (RS) and RS to mobile station (MS) links. This may not be realistic and hence our proposed model considers asymmetric resource allocation (ARA) in which the transmission durations are asymmetric. Very little work has been done in ARA for relay-aided networks and most of them considered only power allocation. The queue stability and quality of service (QOS) requirements are other considerations that have a significant impact on RA and hence are considered in this work. The QOS requirements can be brought in terms of the maximum delay threshold and the minimum throughput requirements. The interference threshold is evaluated from the QOS of the primary radio network. Based on the queue state information, channel state information and QOS, resources are allocated to the secondary radio network. Our proposed ARA differs from existing ARA schemes in terms of additionally considering the subcarrier pairing for resource allocation. This work evolves an optimal cross-layer based ARA considering the above mentioned factors into account. The proposed ARA includes subcarrier allocation, subcarrier pairing and power allocation. Simulation results show that the proposed ARA scheme increases the system throughput and serves the edge users satisfactorily.

A 3rd Generation Partnership Project (3GPP) Long Term Evolution (LTE) system uses the concept of two-tier heterogeneous networks (HetNets), where low-power and short-range femtocells are laid under macrocells to fulfill the quality of service (QoS) requirements of users and to boost overall network capacity. However, co-channel interference is one of the major issues that need to be resolved for the successful deployment of HetNets. To overcome this problem, fractional frequency reuse (FFR) schemes have been proposed that can efficiently utilize the available spectrum. Nevertheless, these schemes waste limited frequency resources owing to their static allocation and lack of following QoS requirements, network loading conditions, and service priority of users. In this paper, a QoS-based dynamic FFR (QoS-DFFR) scheme is proposed that efficiently allocates the non-occupied center-zone frequency bands, i.e., bonus bandwidth (BBW), to cell-edge users by considering their QoS requirements. Consequently, the proposed QoS-DFFR scheme can optimize cell-edge user throughput and sector throughput and reduce co-channel interference by dynamically allocating the BBW to the most demanding cell-edge users. The proposed QoS-DFFR scheme improves performance because of its ability to dynamically allocate the limited portion of the frequency bands based on the service priorities of users. The system-level simulation results show that the proposed QoS-DFFR scheme performs remarkably well in a HetNet environment. Compared with the usual FFR schemes, the proposed scheme almost doubles the cell-edge user's throughput and reduces the user's packet loss rate.

End-to-end network slicing in unmanned aerial vehicle (UAV) networks has attracted significant attention for delivering differentiated services tailored to the quality of service (QoS) requirements of user terminals (UTs). In a sliced UAV network, the dual mobility of both UTs and UAVs, combined with the three-layer association of UT-UAV-network slice (NS), makes handoff a critical and challenging problem for maintaining the communication performance of UTs. This paper proposes a sequential handoff process where a central controller makes handoff decisions for each UT sequentially according to the UT queue. This process is modeled as a Markov decision process (MDP). In the MDP, the state space includes NS available resources, UTs' QoS requirements, and UT queue information. Additionally, the reward function accounts for UTs' QoS and handoff overhead. The double deep Q-network (DDQN) technique is then employed to design a handoff algorithm. This algorithm achieves the optimization goal of ensuring UTs' QoS requirements while avoiding frequent handoffs by maximizing the total reward of the MDP. Additionally, a state-dependent exploration technique with adaptive intensity adjustment, called noisy network (NoisyNet), is utilized to drive the DDQN for effective exploration, thereby enhancing the performance of the handoff algorithm. Finally, the runtime complexity of the proposed NoisyNet-DDQN-based sequential handoff (NoisyNet-DDQN-SH) algorithm is analyzed. The simulation results show that the NoisyNet-DDQN-SH algorithm converges well. Moreover, it exhibits strong robustness. Additionally, the NoisyNet technique effectively enhances the algorithm's performance, making the NoisyNet-DDQN-SH algorithm superior to the vanilla DDQN (with an ϵ-greedy strategy), greedy, maximum signal-to-interference-plus-noise ratio (MaxSINR), and random algorithms.

Wireless mobile radio systems have to serve users with different quality of service (QoS) requirements. Scheduling algorithms like weighted proportional fair (WPF) have been proposed considering channel gains to improve the system capacity in terms of sector throughput as well as user priorities to fulfill QoS requirements. These scheduling algorithms allow assigning different priority factors to users and services so that different QoS requirements can be fulfilled. This paper provides an analysis of the influence of users with different priorities on the sector and user throughput. It is shown analytically and by system level simulations that the average user throughput can be adjusted by choosing a specific priority factor. Furthermore, it is shown that the sector throughput decreases if WPF scheduling for users with different priorities and full buffer model are considered compared to a scenario with users having equal priority. If QoS requirements for realistic traffic models, e.g. FTP, have to be fulfilled, for each high priority user low priority users have to be removed from the system in order not to exceed an acceptable number of unsatisfied users. It is shown that the decrease in sector throughput with a realistic traffic model and QoS requirements is higher than for the full buffer model.

This paper studies the case of an overlay cognitive radio network where the primary user leases spectral resources to the secondary user in exchange for cooperation, considering that both type of users have specific quality of service requirements. We investigate the problem of joint power and time allocation for the secondary access during the cooperative phase, with a view to optimizing the effective capacity of the primary user given an average energy constraint for the secondary user. Afterwards, the optimal power allocation of the secondary user for its own transmission phase is investigated in order to maximize the effective capacity of the secondary link. The proposed joint power and time allocation mechanism is compared with an optimal time/constant power allocation scheme and a less sophisticated baseline allocation scheme, i.e. power allocation under constant time and its superiority is proven for various network parameters. The reference model of one primary---one secondary user is extended to a general multi user cognitive radio network through the proposed pairing mechanism based on matching theory. Particularly, considering the remarks of the reference scenario, we propose two different matching schemes (with/without consideration of primary users' quality of service requirements) and we confirm their superiority compared to other matching mechanisms.

Although cloud storage service (CSS) is convenient to access data, the cost, security, and performance are the issues to users who consider to adopt CSS. For example, CSS could be unavailable due to technical issues or natural disaster. In order to avoid single point of failure, many users duplicate data into multiple CSS providers (CSPs). However, this will increase cost; decrease security; and is difficult to maintain data consistency. In this paper, we propose a QoS-aware Distributed Cloud Storage Service (QDCSS) which aims to provide users with the appropriate CSS according to their quality of service (QoS) requirements. In QDCSS, the data will be encoded into code words by applying erasure code and then the code words will be smartly distributed to multiple CSPs to meet users' QoS requirements. Compared with data duplication, the numerical analysis show that QdCSS can reduce cost by 73% and improve security by 63%. Moreover, the simulation results show that QDCSS can adapt to different users' QoS requirements.

The most precious resource for the mobile network operators (MNOs) is the radio spectrum, cardinal for meeting the quality of service (QoS) requirements of the users. An integral technology of the budding fifth generation (5G) wireless communication networks (WCNs) is device-to-device (D2D) communication. To make use of the gains offered by D2D communication, optimal resource sharing with the cellular users in the network is necessitated. This paper proposes an adaptive resource block (RB) allocation scheme, using Hidden Markov Model (HMM), to assure adequate resource availability to each demanding D2D pair in the network. The adaptive allocation of resources improves the system throughput and energy efficiency (EE), meeting the QoS demands of the D2D pairs and fostering green communication. Since RB sharing is between pairs and cellular users, interference rises. The improvement in performance is achieved by sectoring the cellular coverage region, which diminishes the interference levels. The potency of the proposed adaptive scheme has been verified through simulations.

Component-based development (CBD) techniques have been widely used to enhance the productivity and reduce the cost for software systems development. However, applying CBD techniques to embedded software development faces additional challenges. For embedded systems, it is crucial to consider the quality of service (QoS) attributes, such as timeliness, memory limitations, output precision, battery constraints. Frequently, multiple components implementing the same functionality with different QoS properties can be used to compose a system. Also, software components may have parameters that can be configured to satisfy different QoS requirements. Composition analysis, which is used to determine the most suitable component selections and parameter settings to best satisfy the system QoS requirement, is very important in embedded software development process. In this paper, we present a model and the methodologies to facilitate composition analysis. We define QoS requirements as constraints and objectives. Composition analysis is performed based on the QoS properties and requirements to find solutions (component selections and parameter settings) that can optimize the QoS objectives while satisfying the QoS constraints. We use a multiobjective concept to model the composition analysis problem and use an evolutionary algorithm to determine the Pareto-optimal solutions efficiently.

With the rapid development of BSG/6G and cellular vehicle-to-everything (C-V2X) technologies, the service demands of connected vehicles are diversifying, and the quality of ser-vice (QoS) requirements are also significantly improving. How to reasonably allocate the resources of C-V2X network and maximize the service quality has aroused wide concern. To this end, this paper proposes a dynamic base station (BS) accessing and resource allocation method for the downlink BSs of the next generation fully-decoupled C-V2X network, which allocates network resources according to the types of vehicles with different QoS requirements. Specifically, vehicles select the access BSs cluster for multi-connectivity, and BSs allocate appropriate band-width resources according to the QoS requirements. This paper proposes to use the Lyapunov stochastic optimization method to transform the long-term optimization problem, that is, to optimize the vehicle QoS and resource management dynamically during a period of time, into the optimization of the Lyapunov drift-plus-penalty function on each time slot, and use Markov approximation technique to approximate the selection of the global optimal access BSs cluster dynamically for either the delay-sensitive vehicles or the high-rate-guaranteed vehicles. By comparing the performance of this method with the benchmark approach, it is confirmed that the method proposed in this paper has certain advantages.

IEEE 802.16 is a standardisation for a broadband wireless access in metropolitan area networks (MAN). Since the IEEE 802.16 standard defines the concrete quality of service (QoS) requirement, a scheduling scheme is necessary to achieve the QoS requirement. Many scheduling schemes are proposed with the purpose of throughput optimisation and fairness enhancement, however, few scheduling schemes support the delay requirement. In this study, the authors propose a new scheduling scheme reflecting the delay requirement. Specifically, the authors add the delay requirement term in the proportional fair scheduling scheme and the scheduling parameters are optimised with respect to the QoS requirement. Therefore the QoS requirement is achieved without the excessive resource consumption.

In the Internet of Things (IoT) paradigm, data is gathered for treatment from locals, machines, vehicles, etc. Cloud computing is providing suitable hardware and software for data processing. Thus, the integration of IoT with cloud capabilities offers several benefits for many applications. However, challenges persist for some use-cases like delay-sensitive services due to the huge amount of information collected by IoT devices and to be processed by cloud servers. Fog computing is expected to overcome several limits and challenges in cloud computing concerning the Quality of Service (QoS) requirements like latency, bandwidth and location awareness. Nevertheless, researchers still have to deal with several issues namely the architectural level and the energetic aspect. In this paper, we investigate fog system architectures and energy consumption in literature, while considering QoS requirements in the synthesis. A system model is then introduced with a potential solution for QoS management for fog computing environment.

The joint design of the multi-stream in MIMO relay sigle/multiple user system is investigated. Under the inter-stream interference, a constrained optimization problem with respect to the unknown relay precoder matrix is formulated with a goal of minimizing the total relay transmit power subject to quality of service (QoS) requirement on each data stream. As the original opitimization problem is non-convex, the matrix expression of the cost function and constrained requirement is converting to a scalar optimization problem and the optimal relay precoder and receive filter are obtained. The optimal design of the multiple user relay system under QoS requirement is also provided. By using a reasonable approximation and converting to the generalized Rayleigh form for the cost function, a suboptimal relay precoder matrix for QoS optimization with relay transmit power constraint is obtained. Simulation results demonstrate that for single user model, the minimize relay power will increase with Signal to Interference plus Noise Ratio(SINR) constraint value becoming larger, and for multiple users model, more users in our algorithm will make the MSE gain more obvious as increasing transmitting SNR.