Enhancing OFDM System Performance over Correlated Double Ring Channel

Wireless network is one of the most important things in the development of telecommunication. However, the existing wireless technology has not been able to efficiently create a very high data rate because it was very sensitive to fading. Therefore, Orthogonal Frequency Division Multiplexing (OFDM) technology combined with MIMO (Multiple Input Multiple Output) transceiver system was used to gain more diversity and bandwidth efficiency. The propagation performed on the OFDM MIMO system was multipath propagation. To reduce Intersymbol Interference (ISI) was used Zero Forcing (ZF) equalizer which works by combining channel response and equalizer response itself to eliminate ISI. This study aims to determine the effect of Zero Forcing Equalizer on OFDM MIMO system using rayleigh fading channel and compared the result with OFDM MIMO STBC system. The research method used was simulation using MatLab R2015a. The simulation results showed that the performance of OFDM MIMO ZF system was worse than OFDM MIMO STBC system i.e BER vs EbNo simulation, eye diagram simulation, and constellation diagram simulation. The OFDM MIMO ZF system was required an Eb / No value more than 25 dB to achieve BER 10-4 while the OFDM MIMO STBC system only required an Eb / No value of 10.5 dB to achieve BER 10-4. The eye pattern generated by the OFDM MIMO ZF system was more closed and the dispersion of constellation signals away from the ideal point while OFDM MIMO STBC system displayed a more open eye pattern and the dispersion of its constellation signal closer to the ideal point. It indicated more ISI occurs in the OFDM MIMO ZF system than that in OFDM MIMO STBC system.

In this paper, performance metric of orthogonal frequency division multiplexing (OFDM) system is analyzed over a composite fading channel, i.e., generalized K-fading channel. Here, OFDM system is considered which includes repetition code to enhance the wireless link performance with simplicity. Symbol error rate (SER) performance is evaluated using binary phase shift keying (BPSK) and 16-quadrature amplitude modulation (16-QAM) over generalized K-fading channel. This channel model considers Nakagami-m distribution to define multipath and gamma distribution to represent shadowing effects. Simulation results demonstrate that improved system performance can be achieved by using repetition code in severely faded environment. A comparative study of coded and uncoded system is also given in this paper. Consequently, SER performance is improved with the increase of shape parameters.

We present an implementation of Zero Forcing (ZF) equalizer in OFDM scheme using Software Defined Radio platform whereas NI USRP-2920 as the Radio Frequency (RF) front-end. ZF equalizer is employed to achieve reliable system at the receiver. Center frequency used for data transmission is 915 MHz. The reliability transmission and the performance of ZF equalizer are measured in term of different symbol mapping (i.e., M-PSK and M-QAM). The IQ rate determines the bandwidth available, whereas good performance is achieved with IQ rate less than 1 MHz.ZF equalizer achieves good performance when using BPSK, QPSK and 16-QAM modulation techniques. By applying ZF equalizer, bit error on BPSK and QPSK modulations can be reduced from 29,16% and 39,06% into 0%. This advantage of ZF equalizer also is able to press the bit error on 16- QAM and 64-QAM modulations into 3,125% and 8,85%, respectively.Keywords: OFDM,SDR, USRP,Zero Forcing Equalizer

In orthogonal frequency division multiplexing (OFDM), Fourier Transform (FT) is used as a modulation technique. To avoid inter-symbol interference (ISI) in OFDM by a time dispersive channel, a cyclic prefix (CP) is used which also reduces its spectral efficiency. wavelet packet transform (WPT) as a modulation scheme has been proposed for wireless communication. In this paper, WPT based OFDM is presented and proposed using minimum mean square error (MMSE) equalizer. Equalization is a major factor in wavelets. MMSE is proposed for wavelet based OFDM (WOFDM) based on WPT and compared with zero forcing equalizer (ZFE). The performance is measured for arbitrary magnitude finite impulse response (FIR) channels in the presence of additive white Gaussian noise (AWGN) and impulse noise. Simulation results show a clear improvement in bit error rate (BER) for MMSE over ZFE equalization technique in the presence of noise.

In conventional DFT based orthogonal frequency division multiplexing (OFDM), cyclic prefix (CP) is used to avoid the inter symbol interference (ISI) caused by a time dispersive channel. A solution has been proposed in literature, which involves replacing DFT with wavelet packet transform (WPT) in communication systems. WPT does not require CP and has the attraction of having much lower side lobes. However, in wavelet based multicarrier systems, channel equalization remains an open research area. In this article, a time-domain zero-forcing equalizer (ZFE) for wavelet packet based OFDM (WOFDM) is proposed. The performance comparison of DFT-OFDM and WOFDM is given for an arbitrary FIR channel with different types of wavelet packets. Simulation results show improvement in bit error rate (BER) performance for WOFDM.

This paper introduces four block joint detection (JD) receivers which combining the orthogonal frequency division multiplexing (OFDM) and code division multiple access (CDMA) techniques, i.e., OFDM-CDMA receiver. The performance of the OFDM-CDMA receiver with orthogonal and non-orthogonal spreading sequences is investigated in mobile radio channels. The sequences considered as spreading codes are orthogonal Walsh-Hadamard, Orthogonal Gold, Gold and maximim length sequences or m - sequences. The JD algorithms for the OFDM- CDMA receiver are Zero Forcing Block Linear Equalizer (ZF- BLE), Minimum Mean Square Error Block Linear Equalizer (MMSE-BLE), with and without decision feedback (DF). Time- domain equalization does not require DFT or FFT operations and can be used to compensate the channel fading effect. Hence for hardware implementation, the time domain interpretation can lead to a more efficient structure when compared with the frequency domain approach. The bit error rate (BER) performance comparisons of different spreading codes and equalizers are shown in the simulations.

The WiMax (Worldwide Interoperability for Microwave Access) is a technology in<strong> </strong>broadband wireless access, which employs OFDM (Orthogonal Frequency Division Multiplexing) as an alternative transmission to enable high speed data in communication system. This research aim is to analyze the performance system of the OFDM-Based WiMAX, which used the cyclic prefix. The model was designed in four schemes of simulation method, the BPSK (Binary Phase Shift Keying, QPSK (Quadrature Phase Shift Keying), 16 QAM (Quadrature Amplitude Modulation) and 64 QAM. Each scheme was investigated BER (Bit Error Rate) on AWGN (Additive White Gaussian Noise) channel and multipath Rayleigh fading channel, which had applied the cyclic prefix. By simulation of the cyclic prefix was produced the modulation measurement of the BPSK, QPSK, 16 and 64 QAM. The performance result of Eb/No 15 dB was obtained the BER of BPSK and QPSK of 1.11E-11, the BER of 16 QAM and 64 QAM of 8.69E-06 and 0.00333 respectively. Those results indicated much smaller BER value than EbNo 0 dB which BPSK and QPSK of 1 BER, 1.5 and 1.75 BER for 16 QAM and 64 QAM respectively. In conclusion, a higher value of EbNo, hence the BER value would be lower.

We examine through numerical simulations the performance of three equalizers for CDMA downlink in which the channel is frequency-selective: the traditional RAKE receiver, and chip-spaced MMSE (minimum mean square error) and ZF (zero-forcing) equalizers. These simulation results provide an upper-bound on average BER performance for users near a single transmitting base-station, in which the channel is assumed static and known. We present results for two channel models: a random 4-path multipath channel with delay spread of 10 micro seconds, and an empirically derived random multipath channel generated by the commercial software package SMRCIM. We compare the cases of diversity obtained by two spatially separated antennas to two virtual channels obtained through oversampling a single antenna's received signal. This simulation study has yielded the expected result that spatial diversity is preferable to diversity obtained via oversampling. Furthermore, the MMSE always out-performs both RAKE and ZF equalizers.

Orthogonal frequency division multiplexing (OFDM) is widely used in wireless systems because of its high spectral efficiency, though it is known that it is highly vulnerable to frequency synchronization errors, which severely impede its performance. Such errors arise due to carrier frequency offset and Doppler frequency spread. They destroy the orthogonality among sub carriers and introduce inter carrier interference (ICI). The interference power is proportional to the received signal strength and amount of frequency offset. Several proposal to reduce the impact of ICI in OFDM use very complex signal processing and some have associated bandwidth efficiency loss. Since ICI is inversely proportional to the sub carrier bandwidth, it is interesting to investigate the gains in a system with adaptable sub carrier bandwidth. A system which can support variable sub carrier bandwidths simultaneously meeting the needs of different ICI conditions is compared against a normal OFDM system which uses fixed carrier bandwidth (FSB). Results show that the VSB schemes can be preferred over FSB OFDM system when users with different receive signal strength and Doppler condition have to be served simultaneously.

Performance improvement of a power line communication system is presented here considering the noise as a cyclostationary non-white Gaussian random process. Performance of a power line communication system is severely deteriorated by fading and multipath effect. The impulsive noise has been considered time variant, has short duration, random occurrence with a high power spectral density (PSD). It causes bit error in the signal. Using orthogonal frequency division multiplexing (OFDM) technique, the effect of impulsive noise and fading can be improved greatly. An analytic approach is presented to evaluate the performance of a power line communication link in the presence of the above limitations. The simulation results show that there is deterioration in system BER due to time and frequency dependence of noise and the degradation is found to be significant at higher bit rates and bandwidth. The system suffers penalty in receiver sensitivity due to non-white nature of the noise process. In this paper, an analytical approach using diversity reception is carried out to examine the performance improvement of a power line channel in fading and impulsive noise. The system bit error rate (BER) is compared numerically for both binary phase shift keying (BPSK) and OFDM system. The BER results show that there is significant improvement in OFDM. Also the performance is remarkably upgraded using diversity reception.

In orthogonal frequency-division multiplexing (OFDM) systems, it is generally assumed that the channel response is static in an OFDM symbol period. However, the assumption does not hold in high-mobility environments. As a result, intercarrier interference (ICI) is induced and the system performance is degraded. A simple remedy for this problem is the application of the zero-forcing (ZF) and minimum mean square error (MMSE) equalizers. Unfortunately, the direct ZF method requires the inversion of an NxN ICI matrix, where N is the number of subcarriers. When N is large, the computational complexity can become prohibitively high. As for the direct MMSE method, in addition to an NxN matrix inverse, it requires an extra NxN matrix multiplication, making the required computational complexity higher compared to the direct ZF method. In this dissertation, we first propose a low-complexity ZF method to solve the problem in single-input-single-output (SISO) OFDM systems. The main idea is to explore the special structure inherent in the ICI matrix and to apply Newton's iteration for matrix inversion. With our formulation, fast Fourier transforms (FFTs) can be used in the iterative process, reducing the complexity from O(N^3) to O(Nlog_2 N) . Also, the required number of the iteration is typically one or two. We also analyze the convergence behavior of the proposed method and derive the theoretical output signal-to-interference-noise-ratio (SINR). For the MMSE method, we first reformulate the MMSE solution in a way that the extra matrix multiplication can be avoided. Similar to the ZF method, we then exploit the structure of the ICI matrix and apply Newton's iteration to reduce the complexity of the matrix inversion. For a multiple-input-multiple-output (MIMO) OFDM system, the required complexity of the ZF and MMSE methods becomes more intractable. We then manage to extend the proposed ZF and MMSE methods for SISO-OFDM systems to MIMO-OFDM systems. It turns out that the computational complexity can be reduced even more significantly. Simulation results show that the performance of the proposed methods is almost as good as that of the direct ZF and MMSE methods, while the required computational complexity is reduced dramatically. Finally, we explore the application of the proposed methods in mobility-induced ICI mitigation for OFDM multiple access (OFDMA) systems, and in carrier frequency offset (CFO) induced ICI mitigation for OFDMA uplink systems. As that in OFDM systems, the proposed methods can reduce the required computational complexity, effectively.

Multicarrier acoustic communication has enabled wireless underwater transmission at higher data rates. Several multicarrier modulation systems have been explored in the past for data transmission. Orthogonal frequency division multiplexing (OFDM) fights-off inter-symbol-interference due to orthogonality of the carriers. However, it is susceptible to time variations which introduces inter-carrier-interference. Being double selective, the underwater acoustic (UWA) channel is both time and frequency variant. Time variations and multipath fading makes it a complex channel to estimate. In this paper, we explore linear frequency domain equalization techniques available for radio OFDM systems and compare their performance for a shallow underwater acoustic channel. The underwater channel model used is based on Rician shadowed distribution with Doppler shifts. We compare the performance of a linear equalizer with pilot estimated channel against a zero-forcing equalizer where the channel is assumed to be known. Results collected through Monte Carlo simulations show that for a 128-subcarrier OFDM system and a transmitter-receiver separation of 800 m, a gain of almost 7dB is obtained at a BER of 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">-3</sup> when a zero-forcing equalizer is used. Moreover, when the subcarriers are increased to 256, this gain almost doubles. In conclusion, the zero-forcing equalizer outperforms the LS equalizer for an underwater acoustic channel.

Recently, multicarrier modulations is becoming the chosen modulation technique for wireless communications. The Wavelet Packet Modulation (WPM) is applied as a novel alternative to the Orthogonal Frequency Division Multiplexing (OFDM). In this paper, Wavelet Packet Transform based multicarrier modulation is presented and introduced using both Zero Forcing (ZF) and Minimum Mean Square Error (MMSE) equalizers. They are proposed and compared for Wavelet based multicarrier modulation. First we have evaluated the performance of the classical OFDM and the WPT in term of Power Average Peak Ratio (PAPR). Second, the performances of proposed schemes are qualified for three types of wireless channels in the presence of Additive White Gaussian Noise (AWGN). Results of simulation illustrate a notable enhancement in Bit Error Rate (BER) for MMSE over ZFE equalization technique for different types of channel.

This paper analyzes the channel estimation of rate splitting multiple access (RSMA) wireless network through the full-duplex amplify-and-forward (AF) relay. Basically, full-duplex transmission can improve temporal efficiency, however the loop interference is an unavoidable problem that occurs in the strong user of this proposed network. The orthogonal frequency division multiplexing (OFDM) system is used to provide high data rate communication, assuming the presence of phase noise (PN) in local oscillators. Using the least square (LS) estimate, the channel coefficients of the proposed RSMA relay network are estimated. In addition, convex optimization techniques are applied to estimate the phase noise components of this network. The problem is formulated by optimizing phase noise under transmit power constraints. We analyze the Bit Error Rate (BER) performance of the proposed network under binary phase shift keying (BPSK) modulation and 16-quadrature amplitude modulation (QAM). Simulation results demonstrate that channel estimation achieves better performance after the PN compensation.

In telecommunication, Intersymbol interference (ISI) is a form of distortion of a signal in which one symbol interferes with subsequent symbols. The presence of ISI in the system introduces errors in the decision device at the receiver output. Therefore, in the design of the transmitting and receiving filters, the objective is to minimize the effects of ISI, and thereby deliver the digital data to its destination with the smallest error rate possible. In this paper, we design a zero forcing equalizer, which is a type of linear equalizer used to mitigate the effects of ISI (Intersymbol Interference). The zero forcing equalizer does this by finding the inverse of the impulse response of the channel. The ISI can be studied using eye diagram, which overlays many samples of a signal and can give a graphical representation of the signal characteristics. In this paper the results have been shown with proper eye diagrams. In this paper we also investigate the bit error rate, which is used to estimate the performance characteristics of the zero forcing equalizer.