Experimental Mode Orthogonality and its Consequences

Structural Health Monitoring (SHM) is nowadays common in many branches of engineering since it allows to have a continuous or periodic report of the structural conditions and therefore to promptly intervene if there are incipient damages. The first step to perform a SHM is the identification of the dynamic parameters, i.e. natural frequencies, damping ratios and modal shapes, and it is a crucial step since a modification of the structural parameters can be a direct consequence of structural damages. Among the structural identification methods, Operational Modal Analysis (OMA) methods have received increasing attention from the researchers since they do not require the knowledge of the structural excitation that is due to ambient vibrations and that is usually modeled as a white noise. This aspect makes this kind of methods cheaper and simpler than the classical Experimental Modal Analysis (EMA) methods. In this paper an innovative OMA method is proposed. It is a semi - automated method that allows to identify natural frequencies, damping ratios and modal shapes of a structural system and that can be used also from users that have not knowledge in stochastic dynamics and signal analysis. First of all, the modal shapes are estimated through the use of signal filtering techniques applied on the stochastic properties of the output process and then natural frequencies and damping ratios can be estimated from the mono - component analytical signals obtained by performing a decomposition of the analytical signals matrix. The proposed method has been used to perform the dynamic identification of a real historic building situated in Palermo, i.e. Chiaramonte palace, and the results obtained have been compared with those obtained by using other OMA methods.

Operational modal analysis (OMA) enables the identification of modal characteristics under operational loads and conditions. Traditional frequency-domain methods cannot directly capture modal changes over time, while existing time-frequency representations are not sufficiently interpretable due to spurious modes and implicit parameter design. This paper develops a new OMA method in time-frequency representation based on frequency-domain decomposition (FDD). Short-time FDD and a convolution-based strategy are proposed to obtain singular values and local mode shape similarity, respectively, which are further fused into mode indicators by a fuzzy-based strategy mimicking the modal assurance criterion. The method provides not only a global view of the modal characteristics over time and frequency but also estimates of the modal parameters. It is applicable to strongly nonstationary responses under time-varying loads and conditions. All the parameters explicitly affect the time-frequency representation, and the interpretability is enhanced by including physical information from the user’s prior knowledge in selecting parameters and peak bands. The proposed method is validated based on a study of railway sleepers under train passage. The rigid-body motions and bending modes are identified at frequencies up to 6,500 Hz in laboratory tests and 4,500 Hz in field tests at speeds up to 200 km/h. The identified natural frequencies and mode shapes agree with experimental modal analysis (EMA). The proposed method outperforms EMA in terms of broad frequency range and low measurement cost and can be potentially applied to structural health monitoring under operational conditions.

In order to identify time-varying transient modal parameters only from nonstationary vibration response measurement signals for slow linear time-varying (SLTV) structures which are weakly damped, a moving window differential evolution (DE) independent component analysis- (ICA-) based operational modal analysis (OMA) method is proposed in this paper. Firstly, in order to overcome the problems in traditional ICA-based OMA, such as easy to go into local optima and difficult-to-identify high-order modal parameters, we combine DE with ICA and propose a differential evolution independent component analysis- (DEICA-) based OMA method for linear time invariant (LTI) structures. Secondly, we combine the moving widow technique with DEICA and propose a moving window differential evolution independent component analysis- (MWDEICA-) based OMA method for SLTV structures. The MWDEICA-based OMA method has high global searching ability, robustness, and complexity of time and space. The modal identification results in a three-degree-of-freedom structure with slow time-varying mass show that this MWDEICA-based OMA method can identify transient time-varying modal parameters effectively only from nonstationary vibration response measurement signals and has better performances than moving window traditional ICA-based OMA.

SSI-LSTM network for adaptive operational modal analysis of building structures

The accuracy of modal parameter estimates from estimation methods built in the framework of experimental modal analysis (EMA) can be assessed by several methods provided the information of input loadings and output responses. However, a deeper investigation is necessary for estimation methods built in the operational modal analysis (OMA) framework to establish confidence boundaries for the modal parameter estimates. This paper aims to estimate uncertainties of the modal parameter estimates by testing the sensitivity of the damped natural frequencies, damping ratios, and mode shapes to the choice of the estimation method and data acquisition settings used in this method. The uncertainty estimates of the modal parameter estimates are tested for changes in the boundary conditions. The tests provide insights into tendencies for the accuracy of the modal parameter estimates when the boundary conditions provide a different set of “true” modal parameter values. A simple cantilever beam experimental setup is used to obtain benchmark modal parameter estimates from EMA that are used to estimate the accuracy of the modal parameter estimates from OMA. The method’s robustness in estimating uncertainties and accuracies for modal parameter estimates is tested for several independent experiments. The boundary conditions for the cantilever beam are changed to test the influence of altering modal parameter estimates on the estimated uncertainties and accuracies. The boundary conditions are changed using materials with different elastic properties and the connection pressure between the clamping device and beam. A method presented in Paulsen et al. (Proceedings of the 9th International Operational Modal Analysis Conference, IOMAC, 2022) calculates a representative modal parameter estimate from a set of modal parameter estimates based on weightings obtained from the modal assurance criterion. The method’s ability to reduce uncertainties and increase accuracies of the representative estimate is demonstrated by repeating a test setup ten times. The results present simultaneously a reduction of uncertainties and an increase of accuracies for the representative modal parameter when the weighting method is used. An evaluation of dependencies between the estimated uncertainties and accuracies finds a proportional relation for the damped natural frequency when the uncertainties are described as a relative standard deviation. The analysis presents higher accuracy for the damped natural frequency and mode shape estimates compared to the damping factor, and the accuracy of the damping factor is dependent on the actual value of the damping factor. These phenomena for accuracy are well known and indicate that the uncertainties of modal parameter estimates can be assessed through a sensitivity test of estimation methods and data acquisition parameters.

This paper investigates the use of conventional operational modal analysis (OMA) techniques for modal parameters identification of a rotating system supported by roller bearings. Although largely applied in civil engineering, in-depth studies on different types of systems are still limited in the literature. The novel of the paper is to address such issue by applying conventional OMA methods, such as enhanced frequency domain decomposition (EFDD) and stochastic subspace identification (SSI-data), to identify the modal parameters of a rotating machine, investigating the challenging particularities of these systems due to their inherent operating conditions, especially regarding the presence of harmonic forces, eventually closed-spaced modes, and non-proportional damping due to the bearings. The results presented in the experimental tests showed that, with the use of specific tools, in comparison with traditional experimental modal analysis (EMA), the used OMA methods have managed to successfully identify the modal parameters of a roller bearing supported rotor.

In recent years, theoretical and experimental efforts have transformed the conventional tilting-pad journal bearing (TPJB) into a smart mechatronic machine element. The application of electromechanical elements into rotating systems makes feasible the generation of controllable forces over the rotor as a function of a suitable control signal. The servovalve input signal and the radial injection pressure are the two main parameters responsible for dynamically modifying the journal oil film pressure and generating active fluid film forces in controllable fluid film bearings. Such fluid film forces, resulting from a strong coupling between hydrodynamic, hydrostatic and controllable lubrication regimes, can be used either to control or to excite rotor lateral vibrations. If non-invasive forces are generated via lubricant fluid film, in situ parameter identification can be carried out, enabling evaluation of the mechanical condition of the rotating machine. Using the lubricant fluid film as a non-invasive calibrated shaker is troublesome, once several transfer functions among mechanical, hydraulic and electronic components become necessary. In this framework the main original contribution of this paper is to show experimentally that the knowledge about the several transfer functions can be bypassed by using output-only identification techniques. The manuscript links controllable (active) lubrication techniques with operational modal analysis, allowing for in-situ parameter identification in rotordynamics, i.e. estimation of damping ratio and natural frequencies. The experimental analysis is carried out on a rigid rotor-level system supported by one single pair of pads. The estimation of damping and natural frequencies is performed using classical experimental modal analysis (EMA) and operational modal analysis (OMA). Very good agreements between the two experimental approaches are found. Maximum values of the main input parameters, namely servovalve voltage and radial injection pressure, are experimentally found with the objective of defining ranges of non-invasive perturbation forces.

Operational modal analysis (OMA) is a procedure that allows the modal parameters of a structure to be extracted from the measured response to an unknown excitation generated during operation. Nonlinearity is inevitably and frequently encountered in OMA. The problem: The traditional OMA method based on linear modal theory cannot be applied to a nonlinear oscillation system. The solution: This paper aims to propose a nonlinear OMA method for nonlinear oscillation systems. The new OMA method is based on the following: (1) a self-excitation phenomenon is caused by nonlinear components; (2) the nonlinear normal modes (NNMs) of the system appear under a single-frequency harmonic excitation; and (3) using forced response data, the symbolic regression method (SR) can be used to automatically search for the NNMs of the system, whose modal parameters are implicit in the expression structure expressing each NNM. The simulation result of a three-degree-of-freedom (3-DOF) nonlinear system verifies the correctness of the proposed OMA method. Then, a disc-rod rotor model is considered, and the proposed OMA method’s capability is further evaluated.

Safety assessment of structures for near-field blast-induced ground excitations using operational modal analysis

Stability of lateral rotordynamic modes is an essential consideration during design and acceptance testing of rotating machinery. Experimental modal analysis (EMA) can be used for assessment but is in practice very difficult in actual operating conditions, principally due to the challenges of quantifying the excitation force. Operational modal analysis (OMA) does not require measurement of excitation forces and therefore presents significant logistical advantages over EMA. The background and theoretical concepts of OMA are presented and its use is demonstrated on a 500 kW centrifugal compressor. Measurements performed during commissioning at first raised suspicion that the stability was marginal. However OMA was used to confirm that the first forward mode of the compressor was actually stable and the measurements were reconciled with the predicted behavior. The results show that the assessment of stability margins of rotating machinery can be measured with OMA using only proximity probe data acquired during normal operation.

An Experimental Evaluation of Two Potential Improvements for 3D Laser Vibrometer Based Operational Modal Analysis

Conventionally, modal monitoring of Wind Turbine Rotor Blades is primarily based on the evaluation of eigenfrequencies. Beyond this, combining a sensor network with the Operational Modal Analysis (OMA) method, mode shape and parallely a local component are utilized here. In addition it is expected that the damping, which is also determined by the OMA method, will give a lead on damage development at the rotor already at an early stage. Modal monitoring by means of measurement is combined with FEM simulation and with the comparison of results obtained from measurement and simulation. Moreover, this will establish a connection between the engineer and the design data of a rotor blade, which also are based on FEM analyzes. A further significant increase regarding error resolution is possible by combining the global modal methods with locally sensitive monitoring methods, based on guided elastic waves. These assume plate-like structures through which elastic waves propagate in the low-frequency ultrasonic range (10 - 100 kHz) in certain modes. These different wave modes interact distinctively with inner structural damages such as web fractures and delaminations. It is differentiated between piezoelectrically excited waves (acousto ultrasonics), and waves produced by energy released at fractures, delamination etc. (acoustic emission). Applying a moderate number of sensors, the combination of both methods can allow an effective monitoring of the global structure.

Laminated rubber bearing is a significant device found in structures such as bridges and buildings. It is used to isolate the foundation and the superstructure from seismic loads. Since it is made up from a combination of rubbers and steel plates in alternate layers which make the laminated rubber bearing a complex material, the measurements of damping of the laminated rubber bearing is difficult in practice. Damping is a dissipation of energy or energy losses in the vibration of the structure when the structures are excited with external dynamic loading. An accurate value of damping is very important as damping plays a crucial role in fixing the borderline between stability and instability in many structural systems. Therefore, it is essential to determine the accurate value of damping in structural analysis. Finite element and experimental modal analysis is one of the methods that can be used to determine dynamic properties including damping in any structures. Hence, the main objectives of this research are to determine the natural frequencies, mode shapes, Rayleigh’s damping coefficients, α and β and to evaluate the performance of the laminated rubber bearing components i.e. steel and rubber plates using finite element and experimental modal analysis. Based on the finding, the finite element modal analysis with the added Rayleigh’s damping coefficients α and β shows a good agreement with the experimental modal analysis in term of natural frequencies and mode shapes. The value of natural frequencies reduces after the Rayleigh’s damping coefficients are added into the finite element modal analysis and the minimum and maximum displacement are found to be unaffected by the Rayleigh’s damping coefficients for rubber plate. It can be concluded that modal analysis method can be used to estimate the accurate values of damping ratio and to determine the Rayleigh’s damping coefficients α and β as well.

A recent development in operational modal analysis (OMA) is the possibility of using measured, artificial loads in addition to the unmeasured, ambient excitation, while the ratio between forced and ambient excitation can be low compared to classical experimental modal analysis (EMA). Most of these so-called OMAX algorithms lack the intuitiveness of their EMA and OMA counterparts, since they fit a system model that takes both the measured and the operational excitation into account directly to the measured signals. A more physically intuitive subspace algorithm for OMAX, that starts with an accurate decomposition of the measured joint response in a forced and an ambient part, was recently introduced. In this paper, the performance of this algorithm, which is called CSI-ic/ref, is assessed by means of a case study, where a two-span steel arch footbridge is tested in operational conditions, with and without using additional actuators. From a comparison of the modal parameters with results from a finite elementmodel, an OMA algorithm, and an alternative OMAX algorithm, it can be concluded that CSI-ic/ref yields accurate modal parameter estimates.KeywordsMode ShapeModal ParameterBridge DeckModal Assurance CriterionExperimental Modal AnalysisThese keywords were added by machine and not by the authors. This process is experimental and the keywords may be updated as the learning algorithm improves.

Operational modal analysis based dynamic parameters identification in milling of thin-walled workpiece