- Research Article
210
- 10.1557/mrs.2011.358
Ferroelectric and multiferroic tunnel junctions
- Feb 01, 2012
- MRS Bulletin
- E.Y Tsymbal + 4 more +4
Abstract
The phenomenon of electron tunneling has been known since the advent of quantum mechanics, but it continues to enrich our understanding of many fields of physics, as well as offering a route toward useful devices. A tunnel junction consists of two metal electrodes separated by a nanometer-thick insulating barrier layer, in which an electron is allowed to transverse a potential barrier exceeding the electron’s energy. The electron therefore has a finite probability of being found on the opposite side of the barrier. In the 1970’s, spin-dependent electron tunneling from ferromagnetic metal electrodes across an amorphous Al2O3 film was observed by Tedrow and Meservey(1)(2). Based on this discovery, Julliere proposed and demonstrated that in a magnetic tunnel junction tunnel current depends on the relativemagnetization orientation of the two ferromagnetic electrodes(3). Such a phenomenon nowadays is known as tunneling magnetoresistance(TMR)(4). Magnetic tunnel junctions may be very useful for various technological applications in spintronics devices such as magnetic field sensors and magnetic random access memories. Other insulators are also used for tunnel barriers. For example, epitaxial perovskite SrTiO3 barriers were studied by De Teresa et al. to demonstrate the importance of interfaces in spin-dependent tunneling(5). In tunnel junctions with MgO barriers, Ikeda et al. found large magnetoresitance as high as 604% at room temperature and 1144% at 5 K(6), which approaches the theoretical predictions of Butler et al.(7) and Mathon et al.(8). Despite the diversity of materials used as the barrier of the tunnel junctions, the common feature is that almost all the barriers are nonpolar dielectrics. On the other hand, magnetic insulators, i.e, EuO, EuS and EuSe, are used for tunnel barriers. Spin filtering has been observed in these junctions as were first discussed by Moodera et al.(9). in 1988. They observed that the tunneling current in Au/EuS/Al junction has a spin polarization with the magnitude as high as 80%. and attributed it to the electron tunneling across the spin-dependent barriers (Fig.1). Later, they reported that the tunneling current across Ag/EuSe/Al junctions has an enhanced spin-polarization reaching 97%(10). Recently, using EuO with a higher Curier temperature (69 K) than EuS (16.7 K) and EuSe (4.6 K), Santos et al. obtained 29% spin-polarized tunneling current(11). Naturally, if electrodes are not normal metals, but ferromagnetic materials, both TMR and spin filter effects can be observed(Fig.2)(12). Another important concept is the ferroelectric tunnel junction (FTJ)(13)(14)(15), which take advantage of a ferroelectric as the barrier material. Ferroelectrics possess a spontaneous 2
Ferroelectric and multiferroic tunnel junctions
Abstract
Tunneling magnetoresistance in altermagnetic tunnel junctions with the half-metal electrode
As a critical component of high-efficiency and low-power memory devices, the development of magnetic tunnel junctions (MTJs) with large tunneling magnetoresistance (TMR) is highly demanded. Altermagnets, a particular magnetic system, with zero net magnetizations and non-spin-degenerate conductance due to momentum-dependent spin polarization, can generate TMR when used to replace ferromagnetic and traditional antiferromagnetic electrodes. In this study, we present a ferromagnet/insulator barrier/altermagnet junction that exhibits large intrinsic TMR. In this system, the ferromagnetic electrode is a half-metallic alloy with a unidirectional Fermi surface. We demonstrate that a large TMR can be obtained in V0.5Cr0.5O2/TiO2/RuO2 through first-principles calculations and quantum transport calculations. However, the TMR ratio is almost zero when the ferromagnetic electrode is replaced with pristine VO2 or CrO2. This behavior can be attributed to the unidirectional conduction channel rather than transport direction. Our work presents an efficient approach to realize large TMR ratio in ferromagnet/insulator barrier/altermagnet MTJs, which could contribute to the potential development of altermagnet-based spintronic devices.
Read moreTuning magnetoresistance of chromium chloride tunnel junction through the interface and multi-field effect
<sec>Magnetic tunnel junctions (MTJs) serve as essential platforms for investigating spin transport properties, magnetic phase transitions, and anisotropy in magnetic materials. Recently two-dimensional van der Waals antiferromagnetic insulators like chromium chloride (CrCl<sub>3</sub>) or chromium iodide (CrI<sub>3</sub>) have been used to develop spin-filtering magnetic tunnel junctions (sf-MTJs), improving the device performance for material property exploration and spintronic applications. However, it is crucial to recognize that the spin-filtering effect is not the sole determining factor of tunneling magnetoresistance (TMR) in these junctions; the interface magnetic exchange interactions and adjustable electrode density of states (DOS) fluctuations, response to applied electric or magnetic fields, can also influence the tunneling current.</sec><sec>In this study, we fabricate MTJ devices by using mechanically-exfoliated few-layer CrCl<sub>3</sub> as the tunnel barrier and few-layer graphene (FLG) as electrodes through dry transfer technique. Conducting low-temperature quantum transport measurements, we observe unconventional TMR behaviors, including bias-voltage-dependent TMR, oscillatory tunneling current under high magnetic fields, and tunable tunneling current via gate voltage.</sec><sec>A qualitative model of elastic tunneling current is employed to analyze the spin and band characteristics of the MTJ device. The observed bias-voltage-dependent TMR is attributed to the changes in the tunneling mechanism due to magnetic proximity effect, which induces magnetization in the FLG electrode near the FLG/CrCl<sub>3</sub> interface. The antiparallel alignment of polarized spin to CrCl<sub>3</sub>’s magnetization results in injected charge carriers facing a higher tunnel barrier, leading to negative TMR at lower bias voltages. As the bias voltage increases, the magnetic proximity effect lessens, and the device reverts to its conventional spin-filtering functionality. The oscillatory tunneling current is explained by the graphene electrode’s quantum oscillatory density of states behavior under vertical magnetic fields, which can be controlled by the applied gate voltage.</sec><sec>This study contributes to the understanding of previously unexplored TMR phenomena in two-dimensional MTJs, deepening our insights into carrier transport properties in these heterostructures and broadening avenues for investigating the physical properties of two-dimensional magnetic materials and their spintronic applications.</sec>
Read moreModeling of dielectric breakdown-induced time-dependent STT-MRAM performance degradation
In recent years, spin-transfer torque magnetoresistive random access memory (STT-MRAM) has gained a lot of interest as a promising memory candidate for future embedded applications. STT-MRAM possesses desirable memory attributes such as excellent readability, writability, stability, non-volatility, and unlimited endurance. Moreover, ITRS reports that STT-MRAM can endure 10 <sup xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">15</sup> cycle operations before breakdown thus meeting 10 yrs life-time. As shown in Fig. 1, STT-MRAM bitcell consists of one access transistor and one magnetic tunnel junction (MTJ) (1T-1R). One of the primary reliability concerns in STT-MRAM is the dielectric breakdown of the tunnel junction MgO in the MTJ known as time-dependent dielectric breakdown (TDDB). The thickness of MgO is on the order of 1nm and the voltage across the MTJ during write operation is approximately 0.7V resulting in electric field of ~10MV/cm across it which can induce TDDB. Thus, such high stress conditions can lead to lower breakdown time (T <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">BD</sub> ) which can go even lower with further MgO thickness scaling. In addition to the hard breakdown (HBD) in MTJ which results in very low MTJ impedance and inability to function as memory, experimental results show that soft breakdowns (SBD) also exists. SBDs cause minor degradation in the MTJ resistance and they have shorter average time to appear compared to HBDs. In this paper, we explore in detail the physical mechanism behind both HBD and SBD, and using percolation model we estimate the time dependent degradation in the MTJ performance parameters such as tunneling magneto-resistance (TMR), write current (J <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">C</sub> ), write-time (T <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">WR</sub> ) and lifetime (T <sub xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">LIFE</sub> ).
Read moreUltrafast demagnetization enhancement in CoFeB/MgO/CoFeB magnetic tunneling junction driven by spin tunneling current
The laser-induced ultrafast demagnetization of CoFeB/MgO/CoFeB magnetic tunneling junction is exploited by time-resolved magneto-optical Kerr effect (TRMOKE) for both the parallel state (P state) and the antiparallel state (AP state) of the magnetizations between two magnetic layers. It was observed that the demagnetization time is shorter and the magnitude of demagnetization is larger in the AP state than those in the P state. These behaviors are attributed to the ultrafast spin transfer between two CoFeB layers via the tunneling of hot electrons through the MgO barrier. Our observation indicates that ultrafast demagnetization can be engineered by the hot electrons tunneling current. It opens the door to manipulate the ultrafast spin current in magnetic tunneling junctions.
Read morePolarization-controlled spin reorientation transition and resistive switching in ferromagnetic-ferroelectric nanostructures and tunnel junctions
A spin reorientation transition (SRT) induced in a ferromagnetic nanolayer by the polarization switching in an adjoining ferroelectric film or bulk crystal is described theoretically. It is shown that such a polarization-controlled SRT can be realized in a narrow range of the nanolayer thicknesses only. Our calculations allowing for the polarization-dependent interfacial magnetic anisotropy predict that this ``thickness window'' is located between two threshold thicknesses, at which a size-induced SRT takes place in the ferromagnetic nanolayer at two different directions of the ferroelectric polarization. Importantly, the polarization-controlled SRT manifests itself in the resistance switching occurring in multiferroic tunnel junctions (MFTJs), where an ultrathin ferroelectric barrier is embedded between a ferromagnetic electrode with controllable magnetization and an electrode with a fixed magnetization. Using ${\mathrm{Fe}/\mathrm{BaTiO}}_{3}/\mathrm{Fe}$ junctions as a representative example, we demonstrate that such MFTJs can be employed as electric-write nanoscale memory cells with reliable nondestructive readout and high thermal stability of information storage.
Read moreMetal-Oxide Interfaces in Magnetic Tunnel Junctions
Metal-oxide interfaces play an important role in spintronics—a new area of microelectronics that exploits spin of electrons in addition to the traditional charge degree of freedom to enhance the performance of existing semiconductor devices. Magnetic tunnel junctions (MTJs) consisting of spin-polarized ferromagnetic electrodes sandwiching an insulating barrier are such promising candidates of spintronic devices. The paper reviews recent results of first-principle density-functional studies of the atomic and electronic structure of metal-oxide interfaces in Co/Al2O3/Co and Co/SrTiO3/Co MTJs. The most stable interface structures, O-terminated for fcc Co (111)/α-alumina(0001) and TiO2-terminated with oxygens on top of Co atoms for fcc Co (001)/SrTiO3(001) were identified based on energetics of metal-oxide cohesion at the interface. The covalent character of bonding for both the Co/alumina and Co/SrTiO3 interface structures has been determined based on the pattern of electron distribution across the interface. The Al-terminated Co/alumina interface that corresponds to an under-oxidized MTJ exhibits a metallic character of bonding. The unusual charge transfer process coupled with exchange interactions of electrons in Co results in quenching of surface magnetism at the interface and substantial reduction of work of separation. The electronic structure of the O-terminated Co/Al2O3/Co MTJ exhibits negative spin polarization at the Fermi energy within the first few monolayers of alumina but it eventually becomes positive for distances beyond 10 A. The Co/SrTiO3/Co MTJ shows an exchange coupling between the interface Co and Ti atoms mediated by oxygen, which results in an antiparallely aligned induced magnetic moment on Ti atoms. This may lead to a negative spin polarization of tunneling across the SrTiO3 barrier from the Co electrode. The results illustrate the important fact that spin-polarized tunneling in magnetic tunnel junctions is not determined entirely by bulk density of states of ferromagnet electrodes, but is also very sensitive to the nature of the insulating tunneling barrier, as well as the atomic structure and bonding at the ferromagnet/insulator interface.
Read moreDetection of bottom ferromagnetic electrode oxidation in magnetic tunnel junctions by magnetometry measurements
Surface oxidation of the bottom ferromagnetic (FM) electrode, one of the major detrimental factors to the performance of a magnetic tunnel junction (MTJ), is difficult to avoid during the fabrication process of the MTJ’s tunnel barrier. Since Co rich alloys are commonly used for the FM electrodes in MTJs, overoxidation of the tunnel barrier results in the formation of a CoO antiferromagnetic (AF) interface layer which couples with the bottom FM electrode to form a typical AF/FM exchange bias (EB) system. In this work, surface oxidation of the CoFe and CoFeB bottom electrodes was detected via magnetometry measurements of EB characterizations including the EB field, training effect, uncompensated spin density, and enhanced coercivity. Variations in these parameters were found to be related to the surface oxidation of the bottom electrode, among them the change in coercivity is most sensitive. Annealed samples show evidence for an oxygen migration back to the MgO tunnel barrier by annealing.
Read moreSpin-polarized electron tunneling across magnetic dielectric
This letter deals with a magnetic tunnel junction having spin filtering by a magnetic barrier. We performed experiments in which a relatively strong external field rotates magnetizations of both ferromagnetic electrodes in the tunnel junction with the magnetic barrier simultaneously so that the two are always parallel to each other. The tunnel magnetoresistance induced in this way was over 16% at 300K. The angular dependency of the tunnel current on the layer magnetizations indicates that the barrier contains antiferromagnetic oxide. To achieve the described effect the magnetic electrode of the junction was oxidized prior to forming the Al2O3 layer.
Read moreAnalysis of MTJ Edge Deformation Influence on Switching Current Distribution for Next-Generation High-Speed MRAMs
We have demonstrated 500-MHz operation with our high-speed magnetoresistive random access memory (MRAM). For the next-generation MRAM, reducing magnetization switching current and its distribution is very important for decreasing power consumption. We found that some cells showed both large switching current and large switching current distribution under repeated writing tests. Although some failure modes related to the switching current distribution among multiple cells caused by rotated or shifted magnetic properties have been reported, they do not explain the extraordinary properties of each cell. To determine the origin of these properties, we investigated the influence of magnetic tunnel junction (MTJ) edge concave and convex deformation observed in MRAM fabrication. We found that the edge deformation and changed switching process generated a magnetization vortex, causing large switching current in a simulation. The switching characteristics of MTJs with some MTJ edge structures were fabricated and their characteristics were evaluated. We revealed that the edge deformation causes both large switching current and large switching current distribution of each cell. These characteristics correspond with those observed in the MRAM evaluation. Because cell sizes will become smaller and deformation size will become relatively large in the future, controlling MTJ shapes will become increasingly important for developing next-generation MRAMs.
Read moreThermally Assisted Spin Torque Switching in Magnetic Random Access Memory
Magnetic random access memory (MRAM) consisting of magnetic tunnel junctions (MTJs) is a fascinating candidate for high-density nonvolatile memory. An MTJ has two ferromagnetic metals called free and pinned layers separated by nonmagnetic spacer. The free layer in the MTJ shows two energetically stable states corresponding to the parallel and antiparallel alignments of the magnetizations. These magnetization alignments are distinguished by tunnel magnetoresistance (TMR) effect, i.e., the resistance at the antiparallel alignment is higher than that at the parallel alignment. The free layer is switched between these two stable states by spin torque effect [1], where the transfer of the spin angular momentum from the conducting electrons to the free layer excites the spin torque and induces the magnetization dynamics. The observation of the high TMR ratio more than 100% in CoFeB/MgO-based MTJ [2] has motivated both experimental and theoretical researchers to develop practical MRAM. The free layer should stay one of the stable states to keep information in MRAM. Unfortunately, however, the thermal fluctuation induces probabilistic switching of MTJ. Therefore, high thermal stability is required to guarantee the MRAM performance. Thermal stability of the MTJ is defined by the energy barrier of the free layer separating the two stable states divided by the thermal energy, k B T. Since the retention time of MRAM is exponentially proportional to the thermal stability, a small error in the evaluation of the thermal stability affects the estimation of the retention time significantly. Thus, an accurate evaluation of the thermal stability is necessary. The thermal stability has been evaluated by analyzing the switching probability of the free layer’s magnetization in the thermally activated region assisted by the spin torque. The fitting function of the switching probability is P=1-exp[-ft exp[-Δ(1-I/I c) b ]], where f, Δ, I, and I c are the attempt frequency, thermal stability, current, and switching current at zero temperature, respectively. The switching exponent, b, is assumed to be one [3]. In this study, we study the thermally assisted spin torque switching in an in-plane magnetized MTJ theoretically. The theoretical formula of the switching probability is derived from the Fokker-Planck equation. We find that the switching exponent is larger than one and depends on the applied electric current. The assumption that the switching exponent is one used in previous works is approximately valid only near the low current region, while relatively large current is applied in experiments to obtain the switching probability efficiently. In the high current region, the switching exponent is almost two. We also perform the numerical simulation of the Landau-Lifshitz-Gilbert (LLG) equation with stochastic torque. Figure 1(a) shows the dependence of the probability density, dP/dt, on the current pulse time for several temperatures. As shown, the probability density shows a peak at certain time. We call this time the switching time. Figure 1(b) shows the temperature dependence of the switching time on the temperature. It should be noted that the curvature of the switching time reflects the switching exponent [4]. The nonlinear dependence of the switching time is another evidence that the switching exponent is larger than one. The fact that the switching exponent is larger than one indicates that the previous works have underestimated the thermal stability. The presented formula enables us to evaluate the thermal stability with high accuracy. We also notice that the switching current at zero temperature, I c, can also be evaluated from the switching probability and our formula. We will talk the details of the theoretical analysis of the switching probability and numerical simulation. A comparison with latest experiments will also be presented. (Figure caption) Figure 1: (a) The dependence of the switching probability density on the current pulse time for several temperatures. (b) The temperature dependence of the switching time. [1] J. C. Slonczewski, J. Magn. Magn. Mater. 159, L1 (1996). [2] S. Yuasa, T. Nagahama, A. Fukushima, Y. Suzuki, and K. Ando, Nat. Mater. 3, 868 (2004). S. S. P. Parkin, C. Kaiser, A. Panchula, P. M. Rice, B. Hughes, M. Samant, and S.-H. Yang, ibid 3, 862 (2004). [3] R. H. Koch, J. A. Katine, and J. Z. Sun, Phys. Rev. Lett. 92, 088302 (2004). [4] T. Taniguchi and H. Imamura, J. Nanosci. Nanotechnol. 12, 7520 (2012). T. Taniguchi, M. Shibata, M. Marthaler, Y. Utsumi, and H. Imamura, Appl. Phys. Express 5, 063009 (2012). Figure 1
Read moreSpin-flip assisted tunneling through quantum dot based magnetic tunnel junctions
We theoretically study the spin-polarized transport through double barrier magnetic tunnel junction (DBMTJ) consisting of the quantum dot sandwiched by two ferromagnetic (FM) leads. The tunneling current through the DBMTJ is evaluated based on the Keldysh nonequilibrium Green’s function approach. The self-energy and Green’s function of the dot are analytically obtained via the equation of motion method, by systematically incorporating two spin-flip phenomena, namely, intra-dot spin-flip, and spin-flip coupling between the lead and the central dot region. The effects of both spin-flip processes on the spectral functions, tunneling current and tunnel magnetoresistance (TMR) are analyzed. The spin-flip effects result in spin mixing, thus contributing to the spectral function of the off-diagonal Green’s function components \(\left( {G_{\sigma \bar \sigma }^r } \right)\). Interestingly, the spin-flip coupling between the lead and dot enhances both the tunneling current and the TMR for applied bias above the threshold voltage Vth. On the other hand, the intra-dot spin-flip results in an additional step in the I-V characteristics near Vth. Additionally, it suppresses the tunneling current but enhances the TMR. The opposing effects of the two types of spin-flip on the tunneling current means that one spin-flip mechanism can be engineered to counteract the other, so as to maintain the tunneling current without reducing the TMR. Their additive effect on the TMR enables the DBMTJ to attain a large tunneling current and high TMR for above threshold bias values.
Read moreLarge magnetoelectric effect in organic ferroelectric copolymer-based multiferroic tunnel junctions
We report electrically controlled interfacial spin polarization, or the magnetoelectric effect in multiferroic tunnel junctions by employing organic ferroelectric copolymers, poly(vinylindene fluoride-trifluoroethylene) (P(VDF-TrFE)), as a tunneling barrier. First, we show that the ferroelectric domains and spontaneous ferroelectric polarization of the P(VDF-TrFE) films can be formed in a thin interlayer. Next, we demonstrate that the tunneling magnetoresistance in the unpolarized multiferroic tunnel junction severely quenches from 21% at 20 K to 0.7% at 296 K. Remarkably, we find that the interfacial spin polarization of the device, dubbed spinterface, can be gradually tuned by controlling the ferroelectric polarization with an applied electric field. Specifically, the tunneling electromagnetoresistance can reach around 1000% while the tunneling electroresistance reaches about 30% at 200 K. We speculate that the interface might act as a polarization-dependent spin filter causing the large spinterface effect. The result suggests that organic magnetoelectric-based information storage with four-state bits is feasible at room temperature.
Read moreSpin Polarized Electron Tunneling and Magnetoresistance in Molecular Junctions
This chapter reviews tunneling of spin-polarized electrons through molecules positioned between ferromagnetic electrodes, which gives rise to tunneling magnetoresistance. Such measurements yield important insight into the factors governing spin-polarized electron injection into organic semiconductors, thereby offering the possibility to manipulate the quantum-mechanical spin degrees of freedom for charge carriers in optical/electrical devices. In the first section of the chapter a brief description of the Jullière model of spin-dependent electron tunneling is reviewed. Next, a brief description of device fabrication and characterization is presented. The bulk of the review highlights experimental studies on spin-polarized electron tunneling and magnetoresistance in molecular junctions. In addition, some experiments describing spin-polarized scanning tunneling microscopy/spectroscopy on single molecules are mentioned. Finally, some general conclusions and prospectus on the impact of spin-polarized tunneling in molecular junctions are offered.
Read moreTemperature dependence of magnetoresistance oscillations due to Coulomb staircases in a nanometer vertical ferromagnetic tunnel junction
Magnetic random access memory is considered to be a promising candidate for a future nonvolatile memory. The size of the magnetic tunnel junction (MTJ) cell has been gradually decreasing and has reached the sub-100 nm level. As the size of the MTJ cell approaches the 10 nm level, we must consider the effects of the interaction between the spin-dependent tunneling and the Coulomb blockade, such as magneto-Coulomb oscillation. Spin-dependent tunneling in a nanometer ferromagnetic junction has been investigated in Coulomb blockade regime. The current-bias voltage (I-V) characteristics of NiO/Co/NiO/Co double junctions with a 30 nm contact hole fabricated by an electron beam direct process have been measured in magnetic fields. The temperature dependence of the I-V curve shows clear Coulomb staircases at temperatures below 50 K. At 12 K, the Coulomb threshold of the I-V curve depends on the magnetization configuration, which leads to a tunnel magnetoresistance (TMR) of over 500% around the Coulomb threshold. Although the origin of such a large TMR has not been well proven, spin accumulation in a nanometer metal island is considered. The bias dependence of TMR shows oscillatory behavior due to Coulomb staircases, and at higher temperatures, the TMR oscillations disappear. The TMR oscillation results from the enhancement of TMR at the steps of the Coulomb staircase associated with discrete charging effects and spin accumulations of a nanometer metal island.
Read more