Force interface for the multifingered robotic hand

On-line learning of robot arm impedance using neural networks

In this paper, we propose an adaptive nonlinear strategy for the motion and force control of manipulators with flexible joints. Our approach provides force control when in contact and robust motion control in its absence, all without the need for a control switch. This self-tuning behaviour for mixed contact/non-contact scenarios results from a unified formulation of force and motion control, with an integral transpose-based inverse kinematics core and adaptive update laws to cope with the manipulator flexibility and the contact stiffnesses. The global boundedness of all signals and the asymptotic stability of this controller are guaranteed via Lyapunov analysis. Finally, we validate its applicability experimentally by using low-cost hardware in a realistic mixed-contact scenario, demonstrating low computational demand.

The paper proposes a feedback force and velocity control of an arm exoskeleton to assist user motion. The original published control so-called feedback hybrid force and position control was based on the force and position control and was designed to assist user motion. This original control was successful at providing assist for the user’s arm. This article presents an improved control scheme called the feedback force and velocity control. The proposed control is designed to regulate the velocities of joints of the exoskeleton and the feedback forces on links to assist user motion. The design and optimization of the feedback force and velocity control are realized by the Balancing Composite Motion Optimization (BCMO). The numerical method is realized in the paper to show that the proposed control is better than the original control in terms of less oscillation and fast response.

In this paper, model-based precision force and position control of an ionic polymer metal composite (IPMC) is presented. A 23.8 mm × 3.4 mm × 0.16 mm IPMC strip was used as an actuator in a cantilever configuration. Open-loop force and position responses of an IPMC are not repeatable, and hence closed-loop precision control is of critical importance to ensure proper functioning, repeat-ability and reliability. After feedback controllers were designed and implemented with empirically obtained fourth-order plant transfer functions, the overshoot decreased from 460 to 2.8 per cent and the settling time was reduced from 37.5 to 3.22 s in force control. In position control the overshoot decreased from 333 to 20.3 per cent and the settling time was reduced from 21.5 to 2.56 s. Microscale precision force and position control capabilities of the IPMC actuator were also demonstrated experimentally. An 8 μN force resolution was achieved with a force noise of 0.5μN r.m.s., and the position resolution was 6 μm with a position noise of 2.5 μm r.m.s. The maximum force and tip displacement achieved with the IPMC actuator under closed-loop control were 2 mN and 5 mm respectively. The IPMC actuator could follow various commanded force and position trajectories such as sinusoidal and trapezoidal position profiles, and a velocity profile with a 3 mm/s maximum velocity. A novel hybrid force and position control strategy demonstrated its utility in practical micromanipulalion applications where the actuator force must be limited to prevent damaging micro-objects. High-precision control of the IPMC at low force level proved its potential for micromanufacturing and micromanipulation applications such as robotic and biomedical microgrippers.

The best exoskeleton control strategy depends on the task, motivating the development and analysis of an exoskeleton capable of position, force, and impedance control. In this paper, we implement and compare the three controller types via sliding mode control on a custom-built pneumatic cylinder ankle exoskeleton. To evaluate each controller's performance, the exoskeleton was tested on the benchtop and with human subject experiments. With the position controller, the exoskeleton achieved an root-mean-square error (RMSE) of under 5 deg for both the benchtop and human tests. It had a bandwidth of approximately 12 rad/s. The force controller tracked sinusoidal trajectories acceptably well at low frequencies (15% of force range at 6 rad/s), with a bandwidth of approximately 24 rad/s. The error was significantly higher (RMSE of 24% of force range) for the more biologically relevant trajectory. The impedance controller demonstrated the desired spring-like behavior, with position RMSE generally under 5 deg compared to expected position. All three controllers worked equally well for benchtop and human tests. Thus, a pneumatically powered ankle exoskeleton with sliding mode control is capable of accurate position and impedance control and is capable of marginally acceptable force control.

<div class="htmlview paragraph">A disk brake clamp force controller for electromechanical brakes (EMB) in automotive brake-by-wire systems may be obtained from a standard motion control architecture with cascaded position, speed and current control loops by replacing the outer position control loop with a force control loop. When implemented with proportional, integral and differential (PID) controllers this architecture generally performs well for standard motion control problems, but the EMB control problem is differentiated by a large operating range in which non-linear load disturbances such as friction become significant at high clamp forces of up to 30kN. This paper investigates the feasibility of a cascaded PI control architecture for an EMB with the intention of establishing a baseline standard against which the performance of future control schemes may be compared. Simulation results are presented based on an accepted EMB model.</div>

This paper describes details of a set of robotic fingers driven by stepping motors. Robotic fingers need position, velocity and force control realized by stepping motor. New control system proposed in this study contains a generating system of real-time pulse series for driving stepping motor in the control loop. So, real-time sensor feedback can be achieved in the controlling stepping motor. When the robotic fingers complete a work as an operation, velocity controlled robotic fingers must change to the another control mode such as position or force control. This study treats a method how to provide force control to a robotic finger, and shows a method how to supply a sensor feedback to a stepping motor. It is found that a force controlled robotic finger shows a good performance of parts handling.

Two different control schemes, position model referenced control (PMRC) and force model referenced control (FMRC), are developed for a simplified two robots model with one interacting axis. The dynamic stability of the position (or force) control under the FMRC (or PMRC) is analyzed. Results indicate that PMRC, although providing better dynamic performance of the position control, may degrade the dynamic performance of the force control. However, FMRC can provide better dynamic performance of both position and force control.< <ETX xmlns:mml="http://www.w3.org/1998/Math/MathML" xmlns:xlink="http://www.w3.org/1999/xlink">&gt;</ETX>

Automatic cell injection has been the focus of many researches and commercial development for several years. In this paper, a robotic cell injection system for automatic batch injection of suspended cells is developed. To facilitate the process, these suspended cells are held and fixed to a cell array by a specially designed cell holding device, and injected one by one through an “out-of-plane” cell injection process. A micropipette equipped with a PVDF micro force sensor is integrated in the proposed system. The force sensor is utilized to measure real time injection force applied to the cells during injection process. Through calibration of the relationship between the cell injection force and the desired injector pipette trajectory, a position (vision) and force control algorithm is proposed and applied to the motion control of the injection pipette in three-coordinate directions during an injection process. The out-of-plane cell injection task is decoupled into a position control in X-Y horizontal plane and an impedance force control in Z-axis. The depth motion of the injector pipette, a common problem of three-dimensional micromanipulation, is indirectly controlled by the force control. Finally, experimental results are given to demonstrate the effectiveness of the proposed approach.

Precise force control and position control is essential for many robotic applications. During unilateral or bilateral object handling remote applications, human operators apply excess forces on the actuators with the intention of better grip and it is possible to damage the handled objects. This paper proposes position control and force control techniques when human applies excess force. The controllers consist of predefined force and equilibrium position which are correspond to remote environmental object safety. The operator applied excess force is modeled as a spring force through a virtual stiffness model. The paper introduces proportional derivative position control loop to conventional virtual stiffness controller. The force control loop and the position control loop references are combined in the common dimension of acceleration to produce current reference to the actuator. The sensorless sensing techniques of disturbance observer and reaction force observer are utilized to disturbance suppression and external force estimation. In the force controller, estimated reaction force is reduced to desired value by introducing virtual force loop between reaction force observer output and reaction force feedback input. The position control is achieved by introducing a scaling factor to reaction force feedback path. The switching between force control and position control is possible with scaling factor value. The performances of proposed methods are compared with conventional method and validity of the proposed methods is verified by simulations and experiments.

The contact between robot and environment generates forces of interaction which need to be controlled. In addition, the motion of the robot interacting with the environment must also be controlled. The unification of these two objectives is usually titled ‘force and position control’. In the recent past this issue has been extensively addressed in the research, and several basic approaches to force control have emerged. The synthesis of controllers for force and position control has also been addressed. The paper reviews some of the relevant work in this area in particular the techniques used to generate models of the interaction between robot and environment. The paper also addresses conceptually the implementation of impedance control and presents an application of this technique as well as of the descriptor system to control of interaction forces in a dexterous multifingered hand.

To address the demands for precision and load-bearing capacity in the installation of building panels, a hybrid force-position driven robot with redundant actuation has been developed. The mechanical performance of this robot is primarily governed by its central parallel mechanism, which is equipped with redundant actuators matching the degrees of freedom. Non-redundant and redundant actuators are respectively responsible for position and force control. The inclusion of redundant force-driven joints has increased the internal coupling within the mechanism. To enhance the coordination between position and force control, a hybrid synchronized control method based on cross-coupling has been proposed. Initially, kinematic and dynamic models of the parallel structure were established. Under predefined trajectories, the theoretical inputs for each actuator were calculated using inverse kinematics and dynamics. Subsequently, employing the principle of cross-coupling, the torque output from the position actuators was used as feedback. This feedback was processed by a synchronized coordination controller to adjust the output force of the redundant force-driven joints. By adjusting the output force of the redundant actuators, the torque burden on the position actuators was effectively reduced, thereby enhancing the precision of position control. Additionally, under the same load conditions, smaller power actuators could be utilized for position control, reducing the overall weight of the robot and improving its load-to-weight ratio. To validate the effectiveness of the proposed control strategy, a robotic simulation environment was established. The simulation results demonstrated significant reductions in the average torque required by the position actuators across three different trajectories, with reductions of 91.43%, 54.56%, and 80.6% respectively. Finally, the load-bearing capacity and the load-to-weight ratio of the prototype were assessed. Experimental results confirmed that the prototype achieved a load-to-weight ratio of 15.83%, validating the effectiveness of the hybrid synchronized control method based on cross-coupling.

This paper presents the performance validation of the motion control system for integration force and trajectory information. To realize the implementation high-quality motion that includes contact and non-contact motion to robot system, two contradictory systems; force and trajectory control should be synthesized in one control axis. In order to respond to the request, we proposed a motion synthesis system which integrates two controller in frequency domain. This paper firstly will discuss the acceleration control based force control and position control respectively. And it is also shown that the force reproducibility is decided by contact object's impedance. Then, performance analysis of the motion synthesis system will be shown. From the results, it is confirmed that the motion synthesis system satisfies two control goals without depending on impedance or presence of contact environment. The validity of the design approach is verified by experimental results.

There are many tasks which require robotic manipulators interaction with environment. It consists of three control problems, i.e., position control, impact control and force control. The position control means the way of reaching to the environment. The moment of touching to the environment yields the impact control problem and the force control is to maintain the desired force trajectory after the impact with the environment. These three control problems occur in sequence, so each control algorithm can be developed independently. Especially for redundant manipulators, each of these three control problems has been important independent research topic. For example, joint torque minimization and impulse minimization are typical techniques for such control problems. The three control problems are considered as a single task in this paper. The position control strategy is developed to improve the performance of the task, i.e., minimization of the individual joint torques and impulse. Therefore, initial conditions of the impact control problem are optimized at the previous position control algorithm. Such a control strategy yields improved result of the impact control. Similarly, the initial conditions for the force control problem are indirectly optimized by the previous position control and impact control strategies. The force control algorithm uses the individual joint torque minimization concept. It also minimizes the force disturbances. The simulation results show the proposed control strategy works well.

ABSTRACTA robot interacting with the environment requires that the end effector \\hboxposition is tracked and that the forces of contact are kept below certain reference values. For instance, in a rehabilitation session using a robotic device, the contact forces are limited by the allowed strength of the human limbs and their complex-joints. In these cases, a control scheme which considers both position and force control is essential to avoid damage to either the end effector or the object interacting with the robot. This paper therefore develops a real-time force/position control scheme for a three-DOF parallel robot whose end effector holds a DOF one translation (1 T) and two rotations (2 R). The implemented hybrid force/position control considers, as a reference, the normal force on the mobile platform, which is measured by means of a load cell installed on the platform. The position control is designed to track the orientations of the robot either in joint or task space using a model-based control scheme with identified parameters. Moreover, the force control is based on a PD action. The control scheme is developed through simulations, before being applied to an actual parallel robot. The findings show that with the implemented controller, the actual robot accomplishes the reference values for the normal force on the mobile platform, while at the same time the platform accurately follows the required angular orientation.