GIS partial discharge data enhancement method based on self attention mechanism VAE-GAN

Widely used method for PD (partial discharge) measurement and analysis of existing underground power transmission cables is to store the detected signal pulses as PRPD (Phase Resolved Partial Discharge) data and to analyze the PD defect factors by the pattern type. Although the PRPD pattern data of various facility defects are acquired through the underground power transmission cable diagnosis, due to the PRPD data storage structure, the pulse generation information is destroyed over time, and reconversion into 3D PD pattern (PRPS: Phase Resolved Pulse Sequence) is impossible. Also recently, as a method for verifying the reliability of the power utility prevention diagnosis system, a simulated partial discharge is generated for each facility defect, and the diagnostic system verification that is capable of simultaneously measuring pulses and PD patterns using various sensors is performed, and it is necessary to develop a PD pulse generator based on simulated PRPS data in order to generate the pulses based on PRPS pattern using the existing PRPD pattern, and input the pulses into the system to perform the defect judgment performance test. To solve this problem, this study developed and verified a PD pattern generator that can generate pulses based on PRPS data, and an algorithm that converts existing PRPD pattern data currently owned by Korea Electric Power Corporation (KEPCO) to PRPS pattern data.

This paper presents an investigation on the off-line Partial Discharge (PD) and localization for 1 unit of in-service 5 MVA 33/6.9 kV oil immersed transformer. First, Dissolved Gas Analysis (DGA) was performed to confirm the existence of PD activities. Next, offline PD measurements were carried out on both LV and HV windings. Once the transformer has been energized, PD localization was performed at different sections of the transformer tank. It is found that HV windings are having possible multiples PD activities based on offline Phase-Resolved Partial Discharge (PRPD) pattern and PD localization.

Partial discharge (PD) diagnosis is confirmed to be one of the most effective tools for assessing the health condition of power equipment. Classification and recognition of the measured PD data provide the insulation defects information which facilitate the condition diagnosis of electrical apparatus. This paper presents a new group of image features for partial discharge classification, where the gray images are formed to represent different PD defects. The PD gray images are decomposed into various vectors by two-dimensional linear discriminant analysis (2DLDA), where 9 representative parameters are extracted from each image vector. Finally, fuzzy k-nearest neighbor classifier (FkNNC), multi-class support vector machine (MC-SVM) and back-propagation neural network (BPNN) are respectively employed for PD classification. 419 diversified samples of PD data acquired from typically artificial defect models of oil/pressboard insulation, where the defect size, applied voltage and insulation aging are taken into account, are employed for algorithm validation. The recognition results of 419 PD samples show that the defects are well identified by the proposed 2DLDA features with high accuracy. In addition, the significant increments of average recognition accuracies are obtained by different classifiers compared with the phase-resolved partial discharge (PRPD) features in previous works. The obtained results indicate that the proposed 2DLDA features are potentially effective and reliable in recognizing different PD sources and may be considered as an improved PD recognition tool when compared with the intensively used PRPD features.

High voltage equipment can be damaged when there is a failure of the insulation. Failure would be indicated by the Partial Discharge (PD) phenomenon during the pre-breakdown condition. PD detection methods commonly used, such as thermography and acoustic emission (AE), still have some weaknesses. Based on these conditions, this study discusses the detection method of PD containing Ultra High Frequency (UHF) in air insulation using an antenna that can capture electromagnetic waves. The electrodes used are needle to plane. The variables used are the shape and distance of the electrode. Characteristics analyzed during Partial Discharge Inception Voltage (PDIV). The data retrieved would be processed so that it would display Phase Resolved Partial Discharge (PRPD). The results obtained from the antenna would be compared with the leakage current method using the High Frequency Current Transformer (HFCT). PDIV pattern can be observed in the PRPD analysis, and each electrode has the characteristics of PD at a specific phase angle. The dominant PD point electrodes occur at an angle of 331.2 ° to 342 °, the dominant PD box electrodes occur at an angle of 334.8 ° to 356.4 °, and the dominant PD blunt electrode occurs at an angle of 306 ° to 313.2 °. So, it can be concluded that the loop antenna can detect and observe PDIV patterns in air insulation.

<span>Partial discharge (PD) pattern recognition is useful to diagnose insulation condition. PD measurement data is commonly represented in phase-resolved partial discharge (PRPD) format. PRPD is useful as it provides a visible pattern for different PD source and various features can be extracted for PD pattern recognition. Shorter PRPD duration will enable more training data but the information in each data is less and vice versa. This works aims to investigate the effects of using very short duration PRPD data on the accuracy of PD pattern recognition. The results conclude that machine learning models such as Artificial Neural Network (ANN) and Support Vector Machine (SVM) are robust enough such that reduction of PRPD duration from 15-seconds to 1-second causes less than 5 % drop in the classification accuracy. However, this is only true for noise free condition. <span>When the same PD data is overlapped with random noise, the classification accuracy suffers a significant reduction up to 19%. Therefore, longer PRPD duration is recommended to withstand the effects of noise contamination.</span></span>

This study is focused on solution to the problem that may occur due to noise signals when using the image obtained through the conventional partial discharge preprocessing methods as inputs to the CNN-based partial discharge pattern classifier. To solve such problem, a new data preprocessing method is proposed by considering a projection technique. In the data information obtained through the conventional partial discharge preprocessing methods, data information of useless noise signal leads to the problem of performance degradation when constructing highly qualified pattern classifier based on the data information of partial discharge signal. The proposed preprocessing method called as ‘Projection’ in this study is designed to solve this problem and improve a classification performance of CNN-based partial discharge pattern classifier. First of all, through GIS simulation, one-dimensional partial discharge data is obtained as five cases such as corona discharge, floating discharge, insulator discharge, free particle discharge, and steady state (noise) in an environment with a noise signal by using a UHF sensor. After that, by applying the two conventional partial discharge preprocessing methods such as PRPS(Phase Resolved Pulse Sequence), PRPD(Phase Resolved Partial Discharge) and the proposed partial discharge preprocessing method, one-dimensional partial discharge data is transformed into 3 data types such as image set of PRPS, image set of PRPD, and image set of Projection. Finally each image set is used as inputs to the designed CNN-based partial discharge pattern classifier. Through the comparative analysis of the feature maps of each layer in CNN as well as the performance accuracy of partial discharge pattern classification for each image set, the superiority of the proposed preprocessing method is demonstrated.

Partial Discharge (PD) detection is one of the important methods used to evaluate the insulation condition of in-service high voltage (HV) electrical equipment. On-site PD detection methods are preferred compared to other methods as non-intrusive sensors are easier to install and have no interruptions on the operation. An electrical PD testing utilizing High Frequency Current Transformer (HFCT) installed at the ground terminal of the in-service instrument transformer was used to detect partial discharge activities. However, the limitation of this method is the measurement often lacks of accuracy due to interference in the measured PD waveforms. Therefore, such PD signals are hard to be distinguished from the stochastic noise pulses. Hence, the characteristics of PD signals and interference signals are studied in the Phase Resolved Partial Discharge (PRPD) pattern in order to identify the extent of PD occurrence in the signals. The discharge magnitude could increase significantly because of the noise signals superposed with PD signals. Therefore a method that can remove high magnitude noise will be proposed by using statistical signal processing technique.

This paper proposes a practical partial discharge (PD) severity analysis based on three factors as repetition rate, amplitude and gap time between positive and negative pattern on a phase resolved partial discharge (PRPD) pattern. The PDs are measured by using conventional and unconventional method. The PD amplitude represents PD size. Repetition rate is an average number of PD pulses per second. Gap time is a time distance between two clusters on positive and negative sides in PRPD pattern. Seven 6.6 kV motors were investigated by analysing three parameters, the results show that seven motors encountered high, moderate and low PD severity according to amplitude, repetition rate and gap time. In the first motor, the PRPD pattern shows slot discharge with a high repetition rate and a narrow gap time. This indicates the high risk to motor failure within a short period. The slot discharge was found at stator conductor through ground wall insulation to stator core. In the second motor, the PRPD pattern shows the slot discharge with high repetition rate with the gap time about 5.88 ms. Subsequently, a conventional method according to IEC60270 was performed. The problem was confirmed by visual inspection as stator slot damage by loosen wedge. Finally, the repetition rate, amplitude and gap time analysis were performed with another 5 motors. The results show the different PD severity that were further investigated and confirmed by visual inspection. This PD severity analysis could help to easily analyse, identify problem, predict PD severity and possibility of failure.

Partial discharge detection sensitivity of three types of UHF partial discharge (PD) couplers, reportedly used in the literature, has been studied in comparison using experimentally simulated discharges and those discharges observed during PD acceptance testing of transformers. UHF PD measurements were performed by a digital instrument developed for the purpose. An interesting observation has been that UHF PD inception and detection sensitivity is linked to the appearance of PD pulse current impulses of negative polarity. The occurrence frequencies for PD and common noise sources do not appear to change with the type of the PD coupler used, although individual sensitivities vary. In the last part of the paper typical UHF PD patterns recorded using different couplers during PD acceptance testing of transformer is presented.

The partial discharge (PD) is the most common fault of transformers, which is the main factor affecting the stable operation of transformers. Therefore, the PD should be monitored and identified timely to improve the reliability of the transformers. In this paper, a transformer PD pattern recognition algorithm based on the gray-level co-occurrence matrix of optimal parameters and support vector machine (GLCMOP-SVM) is proposed. Firstly, the GLCM of optimal parameters (GLCMOP) is proposed to be determined by calculating the proportion of the off-diagonal elements (PODE) in GLCM. The GLCMOP has the advantage of avoiding the subjectivity of parameter selection and simplifying the calculation process. Then, the phase-resolved partial discharge (PRPD) maps are used as the PD samples and are converted into the GLCMOP to extract the PD features. Moreover, the feature space of the GLCMOP is dimensionally reduced by screening out the features with high distinguishability, which can improve the generalization ability and recognition speed of the classifier. Finally, the SVM classifier is trained to sort the PD samples and recognize the PD types, which include the tip discharge, surface discharge, and air discharge PD types. Lab tests are performed to verify the accuracy and validity of the proposed methodology. Compared with the traditional algorithms based on GLCM, XGBoost (eXtreme Gradient Boosting) and artificial neural network (ANN), the performance of GLCMOP-SVM is better. The GLCMOP-SVM has less memory consumption and faster recognition speed, so it is very suitable for the online and real-time monitoring of PD occurred in the transformers.

Partial discharge detection on power equipment using a magneto-resistive sensor

This paper proposes a novel phase-resolved partial discharge (PRPD) sensor embedded in a MV-class bushing for high-accuracy insulation analysis. The design, fabrication, and evaluation of a PRPD sensor embedded in a MV-class bushing aimed to achieve the detection of partial discharge (PD) pulses that are phase-synchronized with the applied primary HV signal. A prototype PRPD sensor was composed of a flexible printed circuit board (PCB) with dual-sensing electrodes, utilizing a capacitive voltage divider (CVD) for voltage measurement, the D-dot principle for PD detection, and a signal transducer with passive elements. A PD simulator was prepared to emulate typical PD defects, i.e., a metal protrusion. The voltage measurement precision of the prototype PRPD sensor was satisfied with the accuracy class of 0.2 specified in IEC 61869-11, as the maximum corrected voltage error ratios and corrected phase errors in 80%, 100%, and 120% of the rated voltage (13.2 kilovolts (kV)) were less than 0.2% and 10 min, respectively. In addition, the prototype PRPD sensor had good linearity and high sensitivity for PD detection compared with a conventional electrical detection method. According to performance evaluation tests, the prototype PRPD sensor embedded in the MV-class bushing can measure PRPD patterns phase-synchronized with the primary voltage without any additional synchronization equipment or system. Therefore, the prototype PRPD sensor holds potential as a substitute for conventional commercial PD sensors. Consequently, this advancement could lead to the enhancement of power system monitoring and maintenance, contributing to the digitalization and minimization of power apparatus.

The degradation of oil-impregnated paper induced by partial discharge (PD) seriously affects the life of power equipment. In order to investigate the relationship between partial discharge and the degradation of oil-impregnated paper, PD characteristics and trap parameters of the impregnated paper are measured. In this work, a cavity discharge model is adopted and samples with different degrees of polymerization (DP) are fabricated using thermally accelerated aging to simulate transformers with different lifetimes. For each sample, phase resolved partial discharge (PRPD) spectrograms are recorded for various partial discharge times. The characteristics of partial discharge are analyzed, and the trap parameters of specimens are obtained by the thermally stimulated depolarization current (TSDC) method. Following this, the microstructures of the samples are observed using a scanning electron microscope (SEM). It is found that the damaging breakdown process of oil-immersed paper can be divided into three stages: initial stage, developing stage and pre-breakdown stage. There also exist two levels of trap on the surface of oil-impregnated paper: shallow (0.10-0.59 eV) and relatively deep (0.60-0.90 eV) energy. Importantly, the thermal aging makes the trap energy deeper while electrical aging makes the trap energy shallower.

The reliability of electrical assets is greatly influenced by the quality of their insulations. Key power installations such as power cables are manufactured with polymer-based materials as part of their insulation system. However, accelerated ageing of equipment insulations due to manifestation of defect(s), and partial discharges (PDs) can offset the operation of these systems or even lead to breakdowns. In this study, a non-deterministic model to simulate the phenomenon of repetitive discharges in a spherical air-filled cavity within a practical power cable has been investigated. In addition, the work contributes to the understanding of PD behaviour and field distribution under different ageing conditions considering changes in cavity surface conductivity. First, a section of the practical XLPE cable containing the cavity is developed in 2D using COMSOL software, and a finite element analysis (FEA) of the electric field distribution within the cable insulation is performed. The magnitude of the cavity local field, that is enough to ignite a PD, is investigated. Alongside the COMSOL model, the activity of sustained internal PD is simulated in MATLAB by introducing a random sample generating factor and adjusting the model’s parameters to obtain something close to the practical results. Furthermore, the impact of continuous PD in the power cable under different cavity dimensions and surface conductivity is likewise investigated, and a phase resolved PD (PRPD) pattern is established. The result shows that the magnitude and number of PDs per cycle increase as the cavity size and its surface conductivity increase. Finally, when the cavity surface conductivity rises, the amplitude of the electric field generated by the surface charge distribution and the number of PDs per cycle approach their maximum values.

This paper aims to improve recognition accuracies of single sources of partial discharge (PD) by employing image-oriented feature extraction and selection algorithms. 419 diversified samples of PD data acquired from typically artificial defect models, where the defect size, applied voltage and insulation aging are taken into account, are employed for algorithms validation. In the proposed method, the PD gray images are decomposed into various vectors by two-dimensional principal component analysis (2DPCA) on horizontal and vertical directions, respectively, in which 9 representative parameters are extracted from each image vector. Based on the 419 PD samples, the proposed image features are confirmed to achieve better PD recognition performances than typical image compression methods relevant to 2DPCA. To further improve the recognition performance and reduce the feature dimension, the feature selection technique based on non-dominated sorting genetic algorithm II (NSGA-II) is adopted to search the optimal 2DPCA features. By using the proposed image-oriented feature extraction and selection algorithm, fuzzy k-nearest neighbor classifier (FkNNC), back-propagation neural network (BPNN) and support vector machine (SVM) with 16-dimensional 2DPCA features can now achieve 96.4%, 94.4% and 97.5% accuracies, respectively. The increment of average recognition accuracies of 5%-7% are obtained by different classifiers compared with phase-resolved partial discharge (PRPD) statistical features in previous studies. The investigations on the recognition results relevant to image distortion, cavity discharge change with time and PD contaminated by random noises with different level confirm the robustness of the 16-dimensional 2DPCA features, which signify a great potential in applying the proposed method to field PD pattern recognition in the future.