Graphene based digital microfluidics

We report electrowetting on dielectric (EWOD) experiments using graphene; a transparent, flexible and stretchable nanomaterial. Graphene sheets were synthesized by chemical vapor deposition, and transferred to various substrates (including glass slides and PET films). Reversible contact angle changes were observed on the Teflon-coated graphene electrode with both AC and DC voltages. Nyquist plots of the EWOD reveal that the graphene electrode has higher capacitive impedance than gold electrodes under otherwise identical conditions, suggesting a lower density of pin-holes and defects in the Teflon/graphene electrode than in the Teflon/gold electrode. Furthermore, we have observed reduced electrolysis of the electrolyte and smaller leakage current in the dielectric layer (Teflon) on graphene electrodes than on Au electrodes at the same Teflon thickness and applied voltage. We expect that the improved EWOD properties using graphene as an electrode material will open the door to various applications, including flexible displays and droplet manipulation in three-dimensional microfluidics.

Liquid-liquid extraction techniques are one of the major tools in chemical engineering, analytical chemistry, and biology, especially in a system where two immiscible liquids have an interface solutes exchange between the two liquid phases along the interface up to a point where the concentration ratios in the two liquids reach their equilibrium values [1]. Solutes including nucleic acids and proteins of interests can be extracted from one liquid phase to the other immiscible liquid phase as a preparation step for many analytical processes. There are several advantages in miniaturizing the liquid-liquid extraction methods to on-chip level extraction. Usual advantages of miniaturization are the reduction in the sample size and portability. In addition, transport phenomena is faster in Micro-systems than in ordinary size systems, and therefore, one may expect that liquid-liquid extraction takes less time to achieve in miniaturized devices. It is due to shorter diffusion time in micro scale as well as high surface to volume ratio of Microsystems. Electrowetting on dielectric (EWOD) digital microfluidics is an efficient platform to process droplet based analytical processes [2]. Nanoliter (nL) or smaller volume of aqueous liquid droplets can be generated and transported on a chip by EWOD process. In addition to the high surface to volume ratio, high chemical potential can be expected in droplet based extraction when the droplets are in motion. In this paper, we propose to use room temperature ionic liquid (RTIL) as a second liquid phase for extraction, which forms immiscible interface with aqueous solutions. Properties of RTIL can be tailored by choice of cation, anion and substituents. RTIL has been investigated as replacements for the organic solvents and various “task-specific” ionic liquid are being developed which exhibit many attractive properties such as very low vapor pressure, high thermal stability [3]. We recently published EWOD properties of various RTILs toward microfluidic applications [4]. To demonstrate liquid-liquid micro extraction on chip, we fabricated and tested EWOD digital microfluidic devices. Fig. 1 shows (a) top and (b) cross sectional views of EWOD device. Two model extraction systems were tested. One is organic dye extracted from RTIL (1-butyl-3-methylimidazolium bis(trifluoromethanesulfonylimide or BMIMNTf2) to water and the other is iodine (I2) extracted from water to BMIMNTf2. The later model experiment is demonstrated in Fig. 2. Droplets of aqueous solution and BMIMNTf2 solution were generated on chip reservoir then transported for extraction and separated by EWOD actuation. When an aqueous solution and BMIMNTf2 solution join together, they created an interface, since water and BMIMNTf2 are immiscible. Extraction of I2 was done along the interface. After successful extraction, two immiscible liquid phases were separated by EWOD actuation and formed two separate droplets. From the result shown in Fig 2 (g), it is expected that extraction performance at the interface of moving droplet would be enhanced compared to the stationary droplet, because a moving interface prevent the chemical equilibrium, thus more chemical extraction potential can be provided with a moving interface than at a stationary interface. This demonstration is the first step toward total analysis system. The presented result opens the way to on-chip micro extraction, which will be readily integrated with other sample preparation microfluidic components and detection components. Currently, micro extraction systems for larger molecules such as nucleic acids, proteins and biological cells are being developed for further analytical applications.

To meet the increasing demand of efficient cooling performance in small scale, this paper presents a digital microfluidics (DMF) microscale liquid cooling system which works on the principle of electrowetting on dielectric (EWOD). In EWOD DMF, fluids are handled drop-wise by external electric field. When the dispensed liquid droplet arrives at the hotspot by EWOD DMF operation, it picks up heat and removes heat when it leaves. This process can be repeated for a series of droplets by using a completely automated LabVIEW controlled system connected to the PCB package. With the help of indium tin oxide (ITO) thin film resistance temperature detectors (RTD) and pre-calibrated temperature coefficient of resistance (TCR) data, the temperatures of the hotspot before and after the residence of liquid droplet (i.e., cooling) can be recorded for different frequencies (dwelling time period of droplet on the hotspot) of the drop motion and varying heater power. Future work will involve RTD resistance data collection to plot the heat flux and the temperature difference (before and after cooling) for different frequencies of drop motion. Although the primary focus is to study single phase cooling, the DI water drop will experience considerable evaporation resulting in higher cooling performance. The single phase cooling studies will help in establishing a robust platform for future two-phase cooling analysis in which evaporation effects will be considered.

Electrowetting-on-dielectric (EWOD) technology has been considered as a promising candidate for digital microfluidic (DMF) applications due to its outstanding flexibility and integrability. The dielectric layer with a hydrophobic surface is the key element of an EWOD device, determining its driving voltage, reliability, and lifetime. Hereby, inspired by the ionic-liquid-filled structuring polymer with high capacitance independent on thickness, namely ion gel (IG), we develop a polymer (P)-ion gel-amorphous fluoropolymer, namely, PIGAF, composite film as a replaceable hydrophobic dielectric layer for fabrication of a high-efficiency and stable EWOD-DMF device at relatively low voltage. The results show that the proposed EWOD devices using the PIGAF-based dielectric layer can achieve a large contact angle (θ) change of ∼50° and excellent reversibility with a contact angle hysteresis of ≤5° at a relatively low voltage of 30 Vrms. More importantly, the EWOD actuation voltage did not change obviously with the PIGAF film thickness in the range of several to tens of microns, enabling the thickness of the film to be adjusted according to the demand within a certain range while keeping the actuation voltage low. An EWOD-DMF device can be prepared by simply stacking a PIGAF film onto a PCB board, demonstrating stable droplet actuation (motion) at 30 Vrms and 1 kHz as well as a maximum moving velocity of 69 mm/s at 140 Vrms and 1 kHz. The PIGAF film was highly stable and reliable, maintaining excellent EWOD performance after multiple droplet manipulations (≥50 cycles) or long-term storage of 1 year. The proposed EWOD-DMF device has been demonstrated for digital chemical reactions and biomedical sensing applications.

This paper presents a low temperature technological process ahle to integrate an all-glass microfluidic network with an ElectroWetting On Dielectric (EWOD) structure for the digital handling of liquids. The fluidic channels result from the wet-etching of the glass, while the electrodes necessary for the droplet movement are deposited on the bottom and top surfaces of the microfluidic structure. The bottom electrodes are produced by a selective and sequential photolithographic pattern of a stack of metals, insulation layer and hydrophobic film. The top common electrode is made by a continuous transparent conductive oxide, covered by a hydrophobic layer. Compatibility of the technological steps and mechanical robustness of the proposed device have been tested designing and fabricating a microfluidic network integrating a central chamber, with a volume of about 9 μΐ, two reservoirs, two microfluidic channels and 26 EWOD electrodes. The maximum temperature reached during the device fabrication was 330°C, which is two times lower than the one used for the anodic bonding of glass-based microfluidic network.

This paper reviews the principles, operations, and applications of bubble-based electrowetting-on-dielectric (EWOD). EWOD has proved to be an efficient tool in digital microfluidics that employs discrete droplets, and various applications that use the principles of EWOD have been developed from lab-on-a-chip to optical systems. Similar to its use with droplets, EWOD can also be applied to gaseous bubbles. This review begins with a discussion of the principles of EWOD for a bubble on an electrode covered with a hydrophobic dielectric layer. It then addresses EWOD actuation and the transportation of a bubble in an aqueous medium, along with a physical explanation of bubble motion. The operation of EWOD is then extended to the on-chip creation/elimination and splitting of bubbles. In particular, micro-mixers and pumps are discussed as potential applications of these operations. Unlike droplets, bubbles can be easily oscillated by external excitation, which provides additional functionalities. By integrating EWOD with external excitation, a number of new advanced applications are introduced, including the capture/separation of particles and the propulsion of objects. In these advanced operations, cavitational microstreaming flows and acoustic radiation forces are mainly responsible for the physical mechanisms. This paper also discusses these advanced operations along with their underlying physics. It is expected that in addition to bubble oscillation, other bubble actuation modes will create new functionalities and new potential applications.

This paper describes highly efficient in-droplet particle concentrations/separations (over 91% in efficiency), where magnetic particles are concentrated/separated within a droplet by applying a magnetic field and a subsequent EWOD (electro wetting-on-dielectric) actuation physically splits a magnetic particle-rich region into an individual droplet. This in-droplet method will provide a new functionality of separation/concentration for digital (droplet-based) microfluidics, possibly allowing use of many magnetic-particles-based bio assays in digital microfluidics.

We report the development of a microfluidic device that is the first of its kind to generate uniform arrays of individually addressable cell seeded calcium alginate gels for 3D cell culture using electrowetting on dielectric (EWOD) digital microfluidics (DMF). This is combined with EWOD DMF's multiplexing abilities to demonstrate how a single device is capable of forming cell seeded alginate hydrogels, generating different concentrations of chemicals and delivering these generated chemical concentrations to different alginate gels to observe the effect of chemicals on 3D cultured cells. This lays the foundation for a more efficient and versatile 3D cell culture and chemical screening platform.

This paper describes effect of characteristics of dielectric layer on performances of droplet transport in EWOD (Electro wetting on dielectric) microfluidic devices. EWOD is a technology for manipulating droplets discretely by controlling the surface wettability electrically. Films of Parylene C, PDMS, and SU-8 were prepared for the dielectric layer and effects of deposition method, thickness and permittivity of these films were investigated experimentally. The results show that water droplets can be easily transported at low voltage when the dielectric film with high permittivity is deposited thinly and uniformly.

The present work investigates the effect of variation of length of electrode for a EWOD (electrowetting on dielectric) based microfluidic flow. The discussed model takes into account the effect of energy gradient on droplet movement. The voltage and pitch length are kept constant at 60 V and 200μm respectively. The parameter measured is the velocity of the droplet in the direction along channel length. Various configurations were simulated and the best configuration was attributed to the one with the highest and stable energy gradient. Simulations of droplet movement are done on Coventor Ware. The increase in length of electrode has been found to increase the velocity of droplet movement.

A new sample introduction/analysis approach was developed by combining a digital microfluidic (DMF) device with a portable capillary electrophoresis (CE) analyzer based on short separation capillary and contactless conductivity detection. The DMF sample injection was performed by transporting sample and buffer droplets in succession under the CE capillary inlet end allowing the capillary to be immersed into the sample/buffer droplet, and CE separation was performed by applying a high voltage between the (grounded) buffer droplet and CE outlet reservoir. Electrowetting on dielectric (EWOD) phenomenon was used for droplets actuation. With the use of the DMF sampler, CE separation of a mixture of vitamins was achieved. A droplet evaporation process with simultaneous concentration of sample in the droplet was monitored. It was found that the concentration process closely followed the theoretically predicted function.

Digital microfluidics, by the electrowetting-on-dielectric (EWOD), is a promising way to manipulate biological targets like DNA, proteins, or cells in very small liquid volumes. Conventionally, digital microfluidic operations are performed on a two-dimensional electrode array. This research expands the two-dimensional conventional digital microfluidic architecture into a three-dimensional architecture. The concept relies on the possibility that back and forth motions between open and covered regions are possible under electrowetting actuation. Two face-to-face plates based on “microelectrode dot array” (MEDA) architecture form the foundation of the two-layer microfluidic operations and a dual open/covered hybrid design adds the inter-layer microfluidic connection to complete the three-dimensional system. By combining the advantages of the open/covered systems, a three-dimensional digital microfluidics may achieve better droplet routing capabilities and fit more functions into a given footprint.

This paper demonstrates several enhanced microfluidic functions achieved by integrating two different micro droplet actuation systems (Surface Acoustic Waves (SAW) and ElectroWetting-On-Dielectric (EWOD)). The paper reports how SAW can be employed to help EWOD create and split droplets by augmenting the EWOD force to complete the operation. It also demonstrates how EWOD can be used to guide and precisely position microdroplets for further efficient SAW actuated movement (pumping), concentration and ejection of droplets. The paper also highlights how this combination can also be employed to position droplets for shear wave SAW sensing.

Electrowetting-on-dielectric (EWOD) actuation enables digital microfluidics, typically droplets, to be manipulated on a two-dimensional surface, providing a new platform for manipulating chemicals for multi-step chemical synthesis or assays at the microscale. However, the deficiency of volume precision has long limited its applications in lab on chip (LOC) and micro total analysis systems (μ-TAS) where the accuracy of assays is largely determined by the fluid volume control of the reagent dosing. In this paper, we present a novel electrodes design which improves the reliability of on-chip droplets generating process and reproducibility significantly without any extra external apparatus.

Biosensing at Drop Scale Assisted by Electrowetting at Moderate Frequency